Related Manuals for Joovv Duo
Summary of Contents for Joovv Duo
- Page 1 User Manual Mini • Solo • Duo • Max • Quad • Elite JOOVV.COM JOOVVSOCIAL JOOVVSOCIAL...
- Page 2 © Copyright Joovv, Inc. All rights reserved.
-
Page 3: Getting Started
Section 1 Treatment Guidelines Section 2 Testimonials Section 3 Corporate Office Setup Guides: Joovv, Inc. Joovv Solo or Mini Section 4 940 Calle Amanecer, Suite D Joovv Duo Section 5 San Clemente, CA 92673 Joovv Max Section 6 Customer Service... - Page 4 • Sexual performance • Mental clarity • Relaxation and sleep The light energy emitted by Joovv should be used on bare skin for best results. FDA Indication Joovv is indicated for the relief of muscle spasms, minor muscle &...
- Page 5 But overall improvements in health or skin- Consistency is Key related issues can take 8-12 weeks of consistent use. By using your Joovv on a daily basis, you It’s important to be consistent with your light can maximize your body’s rate of healing.
- Page 6 "Photobiomodulation has a wide range of clinically-proven health benefits. Everything from enhanced muscle recovery, to increased sexual libido, to improved skin health—and much more. After using the Joovv for close to 2 years, it's the only light therapy device I'd ever recommend. Give it a try—you won't be disappointed."...
- Page 7 Setting Up Your Joovv Solo or Mini If you’d prefer instructional setup videos, please visit: www.joovv.com/setup...
- Page 8 1 x Instruction Manual DOOR MOUNTING KIT 1 x Door Hook 1 x Height-Adjusting Pulley For instructions on how to set up your Joovv Mini with the Mini Stand, please refer to the online Setup page at www.joovv.com/pages/setup Approximate setup time: 15-30 minutes...
- Page 9 STEP 1 Place your Solo or Mini face down on a scratch-free surface. Next, screw in the threaded posts to the top of the device and hand-tighten with the included Allen wrench. Then, screw the braided cables to the threaded posts, as shown in Figure A. FIG.
- Page 10 STEP 3 Connect the braided cables to the snap link attached to the height-adjusting pulley. Then, connect the snap link on the opposite end directly to the door hook, as shown in Figure C. FIG. C STEP 4 To raise your Solo or Mini to your desired height, pull down on the loose cable while supporting the device with your opposite hand, as shown in Figure D.
- Page 11 STEP 5 To lower your Solo or Mini, push up on the lever on the height-adjusting pulley while supporting the device with your opposite hand, as shown in Figure E. Be sure to adequately support the device while raising and lowering it with the height-adjusting system.
- Page 12 “Play/ Pause” button a second time. Resume your treatment by pressing the “Play/Pause” button again. That’s it—you’re ready to start Joovvin’! Your Joovv’s cooling fans will run for 5 minutes after the treatment session is complete to cool the LEDs.
- Page 13 Setting Up Your Joovv Duo If you’d prefer instructional setup videos, please visit: www.joovv.com/setup...
- Page 14 Parts List - Door Mount JOOVV DUO 2 x Joovv Solo Devices 1 x Power Cord 4 x Threaded Posts 2 x Braided Steel Cables - 90mm 1 x M5 Allen Wrench 1 x Instruction Manual DOOR MOUNTING KIT 1 x Door Hook...
- Page 15 (2 people required) #1 Lead Mode STEP 1 Place each Solo face down on a scratch-free surface and align, as shown in Figure A. STEP 2 Next, screw in the threaded posts to the tops of both Solos and hand-tighten with the included Allen Lead Mode wrench.
- Page 16 (2 people required) STEP 3 Next, hang the door hook on any standard-size door, as shown in Figure B. Oversized doors may require a different hook. FIG. B STEP 4 Remove one of the snap links from the height- adjusting pulley. Next, connect the braided cables of #1 Solo to the snap link.
- Page 17 (2 people required) STEP 5 To connect #2 Solo, lift it into position below #1 Solo that is already in place. Line up the threaded posts with the holes in the end caps of #1 Solo. Then, insert threaded posts into the holes, and slide forward to lock in place, as shown in Figure D.
- Page 18 (2 people required) #1 Lead Mode STEP 6 Plug the power cord into #2 Solo. Next, connect the power patch cord from the male socket on #1 Solo to the female socket on #2 Solo, as shown in Figure E. #2 Follow Mode FIG.
- Page 19 (2 people required) #1 Lead Mode Locate the pairing switch on #1 and #2 Solos. Turn Lead Mode the switch on #1 Solo to “Lead Mode” and to “Follow Neutral Mode” on #2 Solo, as shown in Figure F. Follow Mode If you don’t wish to connect your devices via Bluetooth, follow the instructions included with the Hardwire Pairing kit.
- Page 20 “Play/ Pause” button a second time. Resume your treatment by pressing the “Play/Pause” button again. That’s it—you’re ready to start Joovvin’! Your Joovv’s cooling fans will run for 5 minutes after the treatment session is complete to cool the LEDs.
- Page 21 Setting Up Your Joovv Max If you’d prefer instructional setup videos, please visit: www.joovv.com/setup...
- Page 22 Parts List — Door Mount JOOVV MAX 2 x Joovv Solo Devices 2 x Joovv Mini Devices 2 x Power Cords 4 x Threaded Posts 4 x Braided Steel Cables - 90mm 1 x M5 Allen Wrench 2 x Door Mount Kits...
- Page 23 Solos and Minis, as shown in Figure A. Attach connection bars using (12) M4x8mm Allen screws and hand tighten using the included Allen wrench. Your Joovv system comes with extra screws. #3 Follow Mode #4 Follow Mode Do not use a drill to install the screws as this can strip the threads.
- Page 24 Door Mount (2 people required) #1 Lead Mode #2 Follow Mode STEP 3 Locate the power patch cords in the Max connection kit. Connect each cord by inserting the female end into #1 Solo and #3 Mini, and male end into #2 Solo and #4 Mini, as shown in Figure B.
- Page 25 Door Mount (2 people required) #1 Lead Mode #2 Follow Mode STEP 4 Locate the pairing switch on each Solo and Mini. Turn the switch on #1 Solo to “Lead Mode” and “Follow Mode” on #2 Solo, #3 Mini, and #4 Mini, as shown in Figure C.
- Page 26 Solos, as shown in Figure D. Next, locate two snap links from the door hook kit and connect them to the braided cables. Your Joovv Max system includes 4 sets of support cables with varying lengths that allow for different heights.
- Page 27 Door Mount (2 people required) STEP 7 With assistance from another person, hold the pair of Solos (#1 and #2) in place. With your free hand connect the snap links to the door hooks, as shown in Figure F. Be sure to adequately support the devices while connecting them to the door hooks.
- Page 28 Door Mount (2 people required) #1 Lead Mode #2 Follow Mode STEP 9 Locate two power cords and plug the female ends into #2 Solo and #4 Mini, plug the opposite end into a wall outlet, as shown in Figure H. Then, turn on the power switches on all devices and your Max will automatically pair.
- Page 29 “Play/ Pause” button a second time. Resume your treatment by pressing the “Play/Pause” button again. That’s it—you’re ready to start Joovvin’! Your Joovv’s cooling fans will run for 5 minutes after the treatment session is complete to cool the LEDs.
- Page 30 Parts List — Optional Mounting Systems (Mobile Stand or Wall Setup) JOOVV MAX 2 x Joovv Solo Devices 2 x Joovv Mini Devices 2 x Power Cords 2 x Threaded Posts (Wall Setup Only) 1 x M5 Allen Wrench 1 x Instruction Manual...
- Page 31 Attach the bracket using (24) M4x6mm Allen screws and hand tighten using the included Allen wrench, as shown in Figure A. Your Joovv system comes with extra screws. Do not use a drill to install the screws as this can #3 Follow Mode #4 Follow Mode strip the threads.
- Page 32 #1 Lead Mode the included Allen wrench, as shown in Figure B. STEP 4 For instructions on how to use your Joovv Max with an optional mounting system, refer to the guide included with that system. Then proceed to step 5.
- Page 33 Optional Mounting Systems (2 people required) STEP 6 Locate the pairing switch on each Solo and Mini. Turn the switch on #1 Solo to “Lead Mode” and “Follow Mode” on #2 Solo, #3 Mini, and #4 Mini, as shown in Figure C. Next, locate the four black rubber floor bumpers and attach by inserting the adjustable nut into the bottom slots of Mini #3 and #4.
- Page 34 Optional Mounting Systems (2 people required) #1 Lead Mode #2 Follow Mode #1 Lead Mode STEP 7 Locate two power cords and plug the female ends into #2 Solo and Mini #4, plug the opposite end into a wall outlet, as shown in Figure E. Then, turn on the power switches on all devices and your Max will automatically pair.
- Page 35 Pause” button a second time. Resume your treatment by pressing the “Play/Pause” button again. That’s it—you’re ready to start Joovvin’! Your Joovv’s cooling fans will run for 5 minutes after the treatment session is FIG. F complete to cool the LEDs.
- Page 36 Setting Up Your Joovv Quad If you’d prefer instructional setup videos, please visit: www.joovv.com/setup...
- Page 37 Parts List — Door Mount JOOVV QUAD 4 x Joovv Solo Devices 2 x Power Cords 4 x Threaded Posts 4 x Braided Steel Cables - 90mm 1 x M5 Allen Wrench 1 x Instruction Manual 2 x Door Mount Kits...
- Page 38 Attach each connection bar using (4) M4x6mm Allen screws and hand tighten using the included Allen wrench. #3 Follow Mode #4 Follow Mode Your Joovv system comes with extra screws. Do not use a drill to install the screws as this can strip the threads. FIG. A...
- Page 39 Door Mount (2 people required) #1 Lead Mode #2 Follow Mode STEP 3 Locate the power patch cords in the Quad Door connection kit. Connect each cord by inserting the female ends into #1 Solo and #3 Solo, and male ends into #2 Solo and #4 Solo, as shown in Figure B.
- Page 40 Door Mount (2 people required) #1 Lead Mode #2 Follow Mode STEP 4 Locate the pairing switch on each Solo. Turn the switch to “Lead Mode” on #1 Solo and “Follow Mode” on Solos #2, #3 and #4, as shown in Figure C. If you don’t wish to connect your devices via Bluetooth, follow the instructions included with the Hardwire Pairing kit.
- Page 41 Door Mount (2 people required) STEP 5 #1 Lead Mode #2 Follow Mode Screw the threaded posts into the tops of each Solo with the included Allen wrench. Then, attach the braided cables to the threaded posts of Solos #1 and #2, as shown in Figure D.
- Page 42 Door Mount (2 people required) STEP 7 With assistance from another person, hold the pair of Solos (devices #1 and #2) in place. With your free hand connect the snap links to the door hooks, as shown in Figure F. Be sure to adequately support the devices while connecting them to the door hooks.
- Page 43 Door Mount (2 people required) #1 Lead Mode #2 Follow Mode Locate two power cords and plug the female ends into Solos #2 and #4, plug the opposite ends into a wall outlet, as shown in Figure H. Then, turn on the power switches on all devices and your Quad will automatically pair.
- Page 44 “Play/ Pause” button a second time. Resume your treatment by pressing the “Play/Pause” button again. That’s it—you’re ready to start Joovvin’! Your Joovv’s cooling fans will run for 5 minutes after the treatment session is complete to cool the LEDs.
- Page 45 Parts List — Optional Mounting Systems (Mobile Stand & Wall Setup) JOOVV QUAD 4 x Joovv Solo Devices 2 x Power Cords 2 x Threaded Posts (Wall Setup Only) 1 x M5 Allen Wrench 1 x Instruction Manual QUAD BRACKET KIT 2 x Power Patch Cords 2 x Connection Bars - 14”...
- Page 46 Attach the bracket using (24) M4x6mm Allen screws and hand tighten using the included Allen wrench, as shown in Figure A. Your Joovv system comes with extra screws. #3 Follow Mode #4 Follow Mode Do not use a drill to install the screws as this can strip the threads.
- Page 47 Allen wrench, as shown in Figure B. STEP 4 For instructions on how to use your Joovv Quad with an optional mounting system, refer to the guide included with that system. Then proceed to step 5. STEP 5...
- Page 48 Optional Mounting Systems STEP 6 (2 people required) Locate the pairing switch on each Solo. Turn the switch to “Lead Mode” on #1 Solo and “Follow Mode” on Solos #2, #3 and #4, as shown in Figure C. #1 Lead Mode #2 Follow Mode Next, locate the four black rubber floor bumpers and attach by inserting the adjustable nut into the...
- Page 49 Optional Mounting Systems (2 people required) #1 Lead Mode #2 Follow Mode Locate two power cords and plug the female ends into Solos #2 and #4, plug the opposite ends into a wall outlet, as shown in Figure E. Then, turn on the power switches on all devices and your Quad will automatically pair.
- Page 50 Pause” button a second time. Resume your treatment by pressing the “Play/Pause” button again. That’s it—you’re ready to start Joovvin’! Your Joovv’s cooling fans will run for 5 minutes after the treatment session is complete to cool the LEDs. 7.14...
- Page 51 Setting Up Your Joovv Elite If you’d prefer instructional setup videos, please visit: www.joovv.com/setup...
- Page 52 Parts List (Mobile Stand & Wall Setup) JOOVV ELITE 6 x Joovv Solo Devices 2 x Power Cords 1 x M5 Allen Wrench 1 x Instruction Manual ELITE BRACKET KIT 2 x Power Patch Cords 1 x Elite Bracket 2 x Connection Bars - 23”...
- Page 53 Allen wrench, as shown in Figure A. #4 Follow Mode #5 Follow Mode #6 Follow Mode Your Joovv system comes with extra screws. Do not use a drill to install the screws as this can strip the threads. FIG. A...
- Page 54 Optional Mounting Systems (2 people required) STEP 3 For instructions on how to use your Joovv Elite with an optional mounting system, refer to the guide #1 Lead Mode #2 Follow Mode #3 Follow Mode included with that system. Then proceed to step 4.
- Page 55 Optional Mounting Systems (2 people required) Locate the pair switch on each Solo. Turn the switch on #1 Solo to “Lead Mode” and “Follow Mode” for Solos #2, #3, #4, #5 and #6, as shown in Figure C. #1 Lead Mode #2 Follow Mode #3 Follow Mode Next, locate the six black rubber floor bumpers and...
- Page 56 Optional Mounting Systems (2 people required) #1 Lead Mode #2 Follow Mode #3 Follow Mode Locate two power cords and plug the female ends into Solos #3 and #6, plug the opposite ends into a wall outlet, as shown in Figure E. Then, turn on the power switches on all devices and your Elite will automatically pair.
- Page 57 “Play/ Pause” button a second time. Resume your treatment by pressing the “Play/Pause” button again. That’s it—you’re ready to start Joovvin’! Your Joovv’s cooling fans will run for 5 minutes after the treatment session is complete to cool the LEDs.
- Page 58 Troubleshooting Guidelines...
- Page 59 110 volts of power. down operation is in effect. • You can check to see if your Joovv system is receiving enough power through the following steps: ⁃ Start by powering on and pairing just the upper row of devices. Power off My door hook is not large enough for my door.
-
Page 60: Frequently Asked Questions
Frequently Asked Questions... - Page 61 The human eye can only see wavelengths of light up to 760 infrared light are energy for your cells. Exposing your body to nm on average. Joovv uses a wavelength of 850 nm for the this light enhances your cells to function at a higher level. The...
-
Page 62: General Information
General Information... -
Page 63: Technical Information
⁃ Use of this device in any way other than described in this manual rated wattage of the devices being powered. voids the warranty and could result in serious injury. • Do not connect more than 3 Joovv devices with the included power 11.1 patch cords, as described in this product manual. - Page 64 The warranty covers all parts and labor during the warranty period with some exclusions. If service is required, the buyer is responsible to return the device to Joovv within Cleaning the 2-year warranty period. The warranty shall not apply to •...
-
Page 65: Corporate Office
Corporate Office Customer Service Joovv, Inc. Email: help@joovv.com 940 Calle Amanecer, Suite D Web: www.joovv.com San Clemente, CA 92673 Setup: www.joovv.com/setup JV-MKTG-PUM-05...