Related Manuals for Hotpoint KVS06
Summary of Contents for Hotpoint KVS06
-
Page 1: Table Of Contents
Use and Care Adapter Plug Air Direction & Air Filter model Appliance Registration Care and Cleaning Condenser Coils Control Settings Electrical Requirements Energy-Saving Tips Extension Cords Grille and Cabinet Grounding 8-11 Instigation Instructions Model and Serial Numbers 2, 5 Problem Solver Repair Service Safety Instructions User Maintenance Instructions 5... -
Page 2: Appliance Registration
Help us help you... Before usiW your air Write down the model Read W instruction before conditioner, read this book and serial numbers. carefully. You’ll find them on a label behind When using this appliance, always the air discharge louvers. They’ll exercise basic safety precautions, It is intended to help you operate including the following:... -
Page 3: Control Settings
Ventilation Control Master Control Switih When this control is set at When you turn the Thermostat OFF turns air conditioner off. “closed” position, only the air Control to the desired setting, the “Fan hi” permits high fan speed inside the room can be circulated thermostat will automaticdlv-control operation without cooling. -
Page 4: Air Direction
(continued) To adjust air direction For normal cooling For quieter operation 1. Set the Master Control at 1. Set the Master Control at “Cool hi?’ “Cool lo” position. 2. Turn the Thermostat Control to 2. Set the Thermostat Control at the desired number. -
Page 5: Care And Cleaning
Vacuum the filter on the dusty side the clamps on the frame. to be steam cleaned, a service to remove light dust. Wash the filter, available through your Hotpoint To replace the grille, lineup the service outlet. water to wash out accumulated dust tabs on each side of the grille with and lint. -
Page 6: Problem Solver
Use This Boblem Solver PROBLEM POSSIBLE CAUSE AND REMEDY AIR CONDITIONER Not plugged in. Plug may have been bumped loose by vacuum cleaner or fimiture. DOES N~ OPERATE If plugged in, fuse could have blown or circuit breaker may have tripped. AIR COND~IONER Curtains, blinds or fumitureblocking front of air conditioner will restrict air flow Thermostat Control may not be set high enough. -
Page 7: Energy-Saving Tips
To obtain service, see your warranty Keep the air filter clean. (See on the back page of this book. instructions on page 5.) We’re proud of our service and . For most efficient cooling, keep want you to be pleased. If for some the vent control in the “closed”... -
Page 8: Instigation Instructions
Installation Instructions Window Requirement Blade-type screwdriver This air conditioner is factory- prepared for installation in standard double-hung windows with Level actual opening width of 22%” Pencil to 39!’ clear, vertical opening of 12%” Screws firnished for minimum from bottom of sash This Instillation to stool. -
Page 9: Electrical Requirements
Electrical Safety— Use of e*nsion cords Use of adapter plw not recommended IMPORTANT... Because of potential safety hazards under certain conditions, Please Read Carefully. Because of potential safety we strongly recommend against hazards under certain conditions, the use of an adapter plug. we strongly recommend against How to connect electricity However, if you still elect to use an... - Page 10 (continued) window. Open Locate and mark centerline of window. 2. Screw leveling bolt in correct 3/8” threaded hold of support channel. Depth of window sill will determine which 3/8” threaded hole to use. 3. Place support channel over centerline of window sill with end against window stool.
- Page 11 7. Close window until it touches Window Sash behind air conditioner top bar. Slide filler panels outward until they touch window sash tracks. (Do not release grip on air conditioner until lower window sash is in final position.) Type A wood screws into lower window sash through mounting holes in top slides.
-
Page 12: Warranty
HOTPOINT FACTORY SERVICE, because of a manufacturing GENERAL ELECTRIC-HOTPOINT defect. FACTORY SERVICE or HOTPOINT CUSTOMER CARE SERVICE. Transportation expense to and from a service shop and shop service labor if required will be free of charge.
Need help?
Do you have a question about the KVS06 and is the answer not in the manual?
Questions and answers