Related Manuals for Hotpoint KED12
Summary of Contents for Hotpoint KED12
-
Page 1: Table Of Contents
How to get Conditioner Use and Care Adapter Plug Air Direction & Air Filter model Appliance Registration Care and Cleaning Condenser Coils Control Settings Electrical Requirements Energy Saver Switch Energy-Saving Tips Extension Cords Grille and Cabinet Grounding Installation Instructions 7-11 Model and Serial Numbers 2, 5 Problem Solver Repair Service... -
Page 2: Appliance Registration
Help us Important Safety help you... Energy-saving tips Instructions Before using your air Read dl i~ructions before Keep the air filter clean. (See instructions on page 5.) conditioner, read this book using this appliance. carefully. . For most efficient cooling, keep When using this appliance, always the vent control in the CLOSED exercise basic safety precautions,... -
Page 3: Control Settings
open VENTILATION THERMOSTAT MASTER CONTROL Ventilation Control Master Control The vent door in your air When you turn the Thermostat conditioner is closed when the Control to the desired setting, the slide switch is to the right. When thermostat will automatically control operation without cooling. -
Page 4: Air Direction
(continued) For normal cooling For quieter operation To adjust air direction 1. Set the Master Control at “Cool 1. Set the Master Control at “Cool Up and down lo” position. 2. Set the Thermostat Control at 2. Turn the Thermostat Control to the desired number (usually 5-7 is the desired number. -
Page 5: Condenser Coils
Hotpoint from the slots at the bottom of the service outlet. frame. After cleaning: Vacuum the filter on the dusty side 1. -
Page 6: Problem Solver
— Use This Roblem Solver POSSIBLE CAUSE AND REMEDY PROBLEM AIR CONDITIONER DOES NOT OPERATE . If plugged in, fuse could have blown or circuit breaker may have tripped. AIR CONDITIONER . Curtains, blinds or furniture blocking front of air conditioner will restrict airflow. “DOES NOT COOL Thermostat Control may not be set high enough. -
Page 7: Adapter Plug
Installation Instructions IMPORTANT: have these instructions with the appliance. OWNER: Keep these instructions for future use. Electrical Safety— Use of adapter plug Use of efiension cords not recommended IMPORTANT... Please Read Carefully. Because of potential safety hazards Because of potential safety under certain conditions, we hazards under certain conditions, strongly recommend against use... - Page 8 (continued) Window Sash Seal Side Retainer Seal-Bottom Rail to Unit Type A Type B Type C Type D Type E Type F Locknut Sill Angle-Bracket Type D Bolt -b “ Qty-2 Qty-3 Qty-4 Qty-2 Qty-2 Qty-4 Hand saw . Hammer Note: All supporting park should be secured to firm wood, Level...
-
Page 9: Window Mounting
Window Mounting Window Requirement 2. Instill Top Angle. (continued) A 1/2” clearance below the window stool is required. If the storm window frame does not allow this clearance, attach a 1 Yz ~ 1. Attach foam gasket , or 2~wide strip of wood along the to top angle as shown. - Page 10 Window Mounting (continued) 4. bcate Cabinet 7. Instill Windowbck in Window. and Sash Seal. 1. Open window and mark center of window stool. 2. Place cabinet in window with bottom stool angle firmly seated over window stool as shown. Bring window down temporarily behind top rail to hold cabinet in place.
-
Page 11: Tools Required
Through-the-Wall Instillation 2. Prepare the Cabinet. The cabinet may be installed through the wall in both existing 1. Remove chassis from cabinet. buildings and new construction. Trim 2. Remove the side retainers. Molding on the outdoor side of the wall. 3. -
Page 12: Warranty
YOUR HOTPOINT ROOM AIR CONDITIONER WARRANTY Save proof of original purchase date such as your sales slip or cancelled check to establish warranty period WHAT IS COVERED FULL ONE-YEAR WARRANTY This warranty is extended to the original purchaser and any...
Need help?
Do you have a question about the KED12 and is the answer not in the manual?
Questions and answers