Table of Contents
Advertisement
Quick Links
Adapter Plug
Air Filter
Appliance Registration
Control Settings
Electrical Requirements
Energy-Saving Tips
Extension Cords
Instigation Instructions
Problem Solver
Repair Service
Safety Instructions
Back Cover
800.626.2000
7
4
5
2
5
5
3,4
9
7
9
5
9
8-11
6
7
2
Use and Care
of
&Initiation
models
KVS1O
KVS12
Advertisement
Table of Contents
Related Manuals for Hotpoint KVS08
Summary of Contents for Hotpoint KVS08
-
Page 1: Table Of Contents
Use and Care Adapter Plug Air Direction &Initiation Air Filter models Appliance Registration Care and Cleaning Condenser Coils KVS1O Control Settings Electrical Requirements KVS12 Energy-Saving Tips Extension Cords Grille and Cabinet Instigation Instructions 8-11 Model and Serial Numbers 2, 5 Problem Solver Repair Service Safety Instructions... - Page 2 Help us Instructions help you... Read dl instructions before Before using your air Write down the model using this apptiance. and serial numbers. conditioner, read this book carefully. When using this appliance, always You’ll find them on a label behind exercise basic safety precautions, the air discharge louvers.
-
Page 3: Thermostat Control
Master Control Switih Thermostat Control Ventilation Control OFF turns air conditioner off. When you turn the Thermostat When this control is set at Control to the desired setting, the “closed” Dosition. onlv the air “Fan hi” permits high fan speed thermostat will automatically-control inside the’room can be-circulated operation without cooling. -
Page 4: Air Direction
(continued) For normal cooling For quieter operation To adjust air direction the Master Control at 1. Set the Master Control at “Cool hi:’ “Cool lo” position. 2. Set the Thermostat Control at 2. Turn the Thermostat Control to the desired number (usually the the desired number. -
Page 5: Care And Cleaning
Vacuum the filter on the dusty side to be steam cleaned, a service the clamps on the frame. to remove light dust. Wash the filter, available through your Hotpoint cleaner side up, under gently flowing To replace the grille, lineup the service outlet. - Page 6 Use This ~oblem Solver PROBLEM POSSIBLE CAUSE AND REMEDY Not plugged in. Plug may have been bumped loose by vacuum cleaner or furniture. AIR CONDITIONER DOES N~ OPERATE . If plugged may have tripped. in, fuse could have blown or circuit breaker AIR CONDITIONER “DOES N~COOL Thermostat Control may not be set high enough.
- Page 7 If You Need Setice To obtain service, see your warranty instructions on page 5.) on the back page of this book. We’re proud of our service and the vent control want you to be pleased. If for some in the “closed” reason you are not happy with the position except when you want to service you receive, here are three...
- Page 8 IMPORTANT: have these instruction with the appliance. OWNER: Keep these instructions for future use. Tools Needed Window Requirement This air conditioner is factory- Blade-type screwdriver prepared for installation in standard Rule or tape measure double-hung windows with Level actual opening width of ~fi” Pencil to 39:’...
-
Page 9: Electrical Safety
Electrical Safety— Use of e*nsion cords Use of adapter plw not recommended IMPORTANT... Because of potential safety hazards under certain conditions, Please Read Carefully. Because of potential safety we strongly reeommend against hazards under certain conditions, the use of an adapter plug. we strongly reeommend against How to connect electricity However, if you still elect to use an... - Page 10 (continued) 1. Open window. Locate and mark centerline of window. Mark two lines 8“ to lefi and 8“ to right of centerline. Window 2. Screw leveling bolt in correct 3/8” threaded hold of support channel. Depth of window sill will determine which 3/8”...
- Page 11 Close window until it touches behind air conditioner top bar. Slide filler panels outward until they touch window sash tracks. (Do not release grip on air conditioner until lower window sash is in final position.) 9. Secure filler panels by driving window sash through mounting holes in top slides.
-
Page 12: Warranty
HOTPOINT FACTORY SERVICE, because of a manufacturing GENERAL ELECTRIC-HOTPOINT defect. FACTORY SERVICE or HOTPOINT CUSTOMER CARE SERVICE. Transportation expense to and from a service shop and shop service labor if required will be free of charge.
Need help?
Do you have a question about the KVS08 and is the answer not in the manual?
Questions and answers