Operation Manual (For Soliton) – GVRP H3C S3100 Series Ethernet Switches Chapter 1 GVRP Configuration Chapter 1 GVRP Configuration When configuring GVRP, go to these sections for information you are interested in: Introduction to GVRP GVRP Configuration Displaying and Maintaining GVRP GVRP Configuration Example 1.1 Introduction to GVRP...
Page 3
Operation Manual (For Soliton) – GVRP H3C S3100 Series Ethernet Switches Chapter 1 GVRP Configuration messages deregister all the attributes, through which the attribute information of the entity can be registered again on the other GARP entities. Leave messages, LeaveAll messages, together with Join messages ensure attribute information can be deregistered and re-registered.
Page 4
Operation Manual (For Soliton) – GVRP H3C S3100 Series Ethernet Switches Chapter 1 GVRP Configuration II. Operating mechanism of GARP Through the mechanism of GARP, the configuration information on a GARP member will be propagated within the whole LAN. A GARP member can be a terminal workstation or a bridge;...
Operation Manual (For Soliton) – GVRP H3C S3100 Series Ethernet Switches Chapter 1 GVRP Configuration Field Description Value It contains multiple Attribute List — attributes. Each general attribute consists of three parts: Attribute Length, Attribute Event, and Attribute Value. Attribute —...
Operation Manual (For Soliton) – GVRP H3C S3100 Series Ethernet Switches Chapter 1 GVRP Configuration Normal. A port in this mode can dynamically register/deregister VLANs and propagate dynamic/static VLAN information. Fixed. A port in this mode cannot register/deregister VLANs dynamically. It only propagates static VLAN information.
Operation Manual (For Soliton) – GVRP H3C S3100 Series Ethernet Switches Chapter 1 GVRP Configuration To do ... Use the command ... Remarks Required Enable GVRP on the port gvrp By default, GVRP is disabled on the port. Note: After you enable GVRP on a trunk port, you cannot change the port to a different type.
Operation Manual (For Soliton) – GVRP H3C S3100 Series Ethernet Switches Chapter 1 GVRP Configuration Table 1-2 Relations between the timers Timer Lower threshold Upper threshold This upper threshold is less than or equal to one-half of the timeout Hold 10 centiseconds time of the Join timer.
Operation Manual (For Soliton) – GVRP H3C S3100 Series Ethernet Switches Chapter 1 GVRP Configuration To do ... Use the command ... Remarks Optional Configure GVRP port gvrp registration { fixed | By default, GVRP port registration mode forbidden | normal } registration mode is normal.
Page 10
Operation Manual (For Soliton) – GVRP H3C S3100 Series Ethernet Switches Chapter 1 GVRP Configuration II. Network diagram Switch B Switch A Eth1/0/1 Eth1/0/1 Eth1/0/2 Eth1/0/3 Eth1/0/2 Eth1/0/1 Eth1/0/1 Eth1/0/1 Switch E Switch C Switch D VLAN 5 VLAN 5...
Page 11
Operation Manual (For Soliton) – GVRP H3C S3100 Series Ethernet Switches Chapter 1 GVRP Configuration Configure Switch B # The configuration procedure of Switch B is similar to that of Switch A and is thus omitted. Configure Switch C # Enable GVRP on Switch C, which is similar to that of Switch A and is thus omitted.
Page 12
Operation Manual (For Soliton) – GVRP H3C S3100 Series Ethernet Switches Chapter 1 GVRP Configuration Configure Ethernet1/0/1 on Switch E to operate in fixed GVRP registration mode and display the VLAN information dynamically registered on Switch A, Switch B, and Switch E.
Need help?
Do you have a question about the S3100 Series and is the answer not in the manual?
Questions and answers