Table of Contents
Advertisement
Quick Links
2-653-913-13(1)
DICOM Color
Printer
Instructions for Use
Page 2
Setup Manual
Page 24
This manual is comprised of the Instructions for Use and the Setup Manual.
The Instructions for Use gives the information on how to use the printer for the
routine work.
The Setup Manual gives the system administrator the information needed to setup
the printer and connect it to the network.
UP-D77MD
© 2005 Sony Corporation
Advertisement
Chapters
Table of Contents
Related Manuals for Sony UP-D77MD
Summary of Contents for Sony UP-D77MD
- Page 1 The Instructions for Use gives the information on how to use the printer for the routine work. The Setup Manual gives the system administrator the information needed to setup the printer and connect it to the network. UP-D77MD © 2005 Sony Corporation...
- Page 2 This unit has been certified according to Standard CSA C22.2 No.601.1. For the customers in the U.S.A and Canada Model UP-D77MD is Non-Patient Equipment. This unit can not be used in the vicinity of patients. * Patient Vicinity When you use this product connected to 240 V single phase, be sure to connect this product to a center tapped circuit.
- Page 3 susceptible equipment. Plug this unit and the susceptible equipment into different branch circuit. Consult your dealer. (According to standard EN60601-1-2 and CISPR11, Class B, Group 1) Caution When you dispose of the unit or accessories, you must obey the law in the relative area or country and the regulation in the relative hospital.
-
Page 4: Table Of Contents
Instructions for Use Table of Contents Introduction Features ...5 System Configuration ...5 Location and Function of Parts and Controls ...6 Front ...6 Rear ...6 Preparation Supplied Accessories ...7 Assembly ...7 Connections ...8 Operation Before Printing ...9 Loading an Ink Ribbon Cassette ...9 Loading the Paper ...10 Printing ...12 Starting to Print ...12... -
Page 5: Introduction
Introduction Features The UP-D77MD DICOM Color Printer is a dye sublimation thermal transfer printer designed to reproduces image data in DICOM format sent via the network. The UP-D77MD has the following functions’ • Equipped with DICOM (Digital Imaging and Communications in Medicine) features... -
Page 6: Location And Function Of Parts And Controls
Location and Function of Parts and Controls For details, refer to the pages indicated in parentheses. Front A !POWER switch Press to turn the printer on or off. B Fan cover (7, 18) Provided to prevent the printer from dust. C Ribbon door (9) Pull the tab (marked with PULL) on the top on the ribbon door to open it when loading an ink ribbon... -
Page 7: Preparation
• Do not turn the printer off while printing. • Do not subject the printer to wide or sudden changes in temperature. Note that the UP-D77MD may not be able to start, if the hard disk is damaged for some reason. Supplied Accessories / Assembly... -
Page 8: Connections
Connections Connect the unit to the 100BASE-TX LAN. Notes • Connect the AC power cord last. • Before connecting to the LAN, be sure to set up the required IP address and sub-net mask. For detailed information, refer to “Setup Manual” provided in the latter part of this manual, and also consult the system administrator. -
Page 9: Operation
Operation Before Printing This section describes the operations that must be performed prior to starting printing. This explanation assumes that the printer has already been installed and that all connections have been made. • Loading an ink ribbon cassette (on this page) •... -
Page 10: Loading The Paper
Wind the spool until the “Start” position marker faces upward. Insert the ink ribbon cassette firmly until it stops. SONY mark faces forwards. Close the ribbon door. Before Printing If your ink ribbon should tear Repair the tear with transparent tape. There should be no problem with using the remaining portion of the ribbon. - Page 11 Be sure to set the spacer according to the size of the paper before placing the paper in the paper tray. Reverse side with printed logos Print surface protection Riffle the paper. sheet Place the paper in the paper tray with the printing surface (shiny side with no legends) and its protection sheet facing...
-
Page 12: Printing
Printing Before printing • Ensure that the printer is properly connected (page 8). • Ensure that the combination of the ink ribbon and paper is correct (pages 9 and 10). • Ensure that the ink ribbon cassette and paper are properly loaded (page 19). -
Page 13: Adjusting Printouts
settings. By selecting a desired user set number, you can make printouts in the desired color. Printer window display Press the MENU button. “INFORMATION” appears. Press the g button. “COLOR ADJUST” appears. Press the f button. “LOAD USER X” appears. Select the desired user preset number by pressing the G or g button. -
Page 14: Adjusting The Color
Adjust the gray. When you adjust the gray, the color intensity is also adjusted. However, adjust the gray first, then adjust the desired color. 1 Select the item for adjustment by using the F or f button. f: Scrolls up to the next item. F: Scrolls down to the previous item. - Page 15 Display “PRINT PATCH” by pressing the F or f button in menu mode. Press the EXEC button. 25 identical images of the image last printed are printed on a sheet of paper as a patch print. Each image has a different color balance, but they have the same gray.
- Page 16 1 In menu mode, display “SAVE /USER X/” by pressing the F or f button. 2 Display the desired user set number by pressing the G or g button. 3 Press the EXEC button. All values adjusted in “Adjusting Gray” on page 13 and here, “Adjusting the Color,”...
-
Page 17: Miscellaneous
• If the unit malfunctions or if a foreign body falls into the cabinet, disconnect the power immediately and consult your Sony service facility or your Sony dealer. Installation • Avoid placing the unit in a location subject to: –... -
Page 18: Cleaning The Thermal Head
To clean the filter, proceed as follows. Remove the fan cover, then filter. Filter Fan cover Clean the filter using the vacuum cleaner and the like. Notes • Be careful that the filter will be caught in the cleaner. • Do not rub the net of the filter strongly. Reset the filter and the fan cover on the side panel as they were. -
Page 19: Ink Ribbon And Paper
The cleaning tip set is available using part number A- 8279-104 (at a charge). Cleaning of the thermal head To clean the thermal head, proceed as follows: Remove the ink ribbon cassette from the printer. Attach the cleaning tip to the cleaning tip holder, and install the cleaning tip holder in the printer. -
Page 20: Specifications
Specifications Power requirements 100 – 240 V AC, 50/60Hz Input current 3.5 A to 1.5 A Operating temperature 10°C to 30°C (50°F to 86°F) Operating humidity 20% to 80% (no condensation allowed) Storage and transport temperature –20°C to +60°C (–4°F to +140°F) Storage and transport humidity 20% to 90% (no condensation allowed) Approx. -
Page 21: Troubleshooting
If a problem appears, check the following trouble shooting guide first and perform whatever action is necessary to solve the problem. If the problem persists, turn off the printer and consult with your Sony dealer. Symptom Possible causes and remedies... - Page 22 If you find a jammed sheet on the way inside the printer, slowly pull it out to the right. If the tray cover is in the way, remove it. If the tray cover is in the way, remove it by lifting it up 1, and then pulling it out to the direction of arrow 2.
-
Page 23: Index
Index Accessories supplied 7, 20 Assembly 7 Bar codes 10 Bottom cover 7, 22 Cleaning Cabinet 17 Filter 17 Thermal head 18 Color printing pack 19 Combination of ink ribbon and paper Connections 8 EJECT button 9 Error messages 21 Fan 7, 17 Features 5 Filter 7, 17... - Page 24 Setup Manual Table of Contents Preparation Overview ...25 Requirements ...25 IP Address ...26 Setup Setting up the Personal Computer to be Used for Setup ...27 About the Setup Window ...27 Opening the Setup Window ...27 Components of Pages ...28 Setup of the Unit ...30 Setup of E-Mail ...30 Confirmation After Setup ...31...
-
Page 25: Preparation
The following hardware and Web browser software are necessary to perform the setup. • Computer: A computer which can be connected to the network connector of the UP-D77MD • Operating system : Microsoft Windows 95, Windows 98, Windows NT 4.0, Windows 2000, or Windows XP •... -
Page 26: Ip Address
Before starting the setup, confirm the following with the network administrator. • The IP address the UP-D77MD will use on the network • Sub-net mask of the network • Gateway address, if a gateway is included in the... -
Page 27: Setup
About the Setup Window The UP-D77MD can be set up on the setup window displayed on the Web browser of the personal computer to be used for setup. The setup window has the following pages: •... -
Page 28: Components Of Pages
Components of Pages Summary/Print Job Page This page displays information on the UP-D77MD. A Printer (printer status) display section Printer Status: Displays the printer status. Paper: Displays the type of paper in use. A4: Displays the size of the paper in use (A4 is always displayed when either A4-size paper or letter-size paper is used in the UP-D77MD.) - Page 29 Printer Status Page This page displays the status of the UP-D77MD. A Printer Status display area Motor/Sensor: Displays the error status or the motor/sensor system. Film/Paper Path: Displays whether of not the paper has jammed in the printing path. Film/Paper Tray: “OK” is always displayed in case of UP-D77MD.
-
Page 30: Setup Of The Unit
IP Address text box Sub-net Mask text box Default Gateway text box 1 Enter the IP address of the UP-D77MD on the network in the IP Address text box. 2 Enter the sub-net mask in the Sub-net Mask text box. -
Page 31: Confirmation After Setup
The settings are saved. Confirmation After Setup After all of settings have been completed Turn off the power of the UP-D77MD and disconnect the UP-D77MD and the personal computer for setup. Proceed as follows to confirm the operation of the UP- D77MD. - Page 32 Sony Corporation...