Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Parkside PBH 1500 F6
Summary of Contents for Parkside PBH 1500 F6
- Page 1 HAMMER DRILL PBH 1500 F6 HAMMER DRILL Original instructions IAN 314988...
-
Page 4: Table Of Contents
Table of contents 1. Introduction ............................Symbols used ....................................... Scope of delivery ...................................... Parts list ..........................................2. Technical data ............................ 3. Safety ..............................Proper use ........................................Residual risks ........................................ General safety instructions for power tools ..........................Safety instructions for hammers ................................ -
Page 5: Introduction
The model name on the hammer drill is a this operating manual, on the hammer drill or on combination of letters and numbers: the packaging. PBH 1500 F6 WARNING! Hammer drill Indicates a hazard that, if not avoided, could result in death or serious injury. -
Page 6: Parts List
The manufacturer can accept no responsibility for damage or injury caused by modifications to the drill. Model No.: PBH 1500 F6 The drill has not been designed for professional, trade or industrial use, but for private users in the Mains connection 230 V ~ / 50 Hz hobby and DIY sector. -
Page 7: General Safety Instructions For Power Tools
General safety instructions for d) Do not abuse the cord. Never use the cord for carrying, power tools pulling or unplugging the WARNING! power tool. Keep cord away Read all safety warnings and all from heat, oil, sharp edges instructions. Failure to follow the or moving parts. - Page 8 d) Remove any adjusting key not allow persons unfamiliar or wrench before turning the with the power tool or these power tool on. A wrench or a key instructions to operate the left attached to a rotating part of the power tool.
-
Page 9: Safety Instructions For Hammers
4. Before Use Safety instructions for hammers 1) Wear ear protection. Noise can WARNING! cause loss of hearing. Disconnect the machine from the 2) Use the auxiliary handles mains before performing any supplied with the machine. maintenance or adjustments. Loss of control over the machine Checking the drill and pack can lead to injury. -
Page 10: Mounting The Depth Stop (Fig. D)
Chuck suitable for use with The hammer drill is intended for use only in places that have a continuous current rating of ≥ 100 A SDS+ system per phase and are supplied with a rated voltage of 230 V by the distribution network. If necessary, •... -
Page 11: Function Selection (Fig. G)
Function selection (Fig. G) Drilling • Choose a drill bit appropriate for the NOTE! application and insert it into the tool as The selector switch should only be described in chapter ‚Inserting the tools‘. used when the motor has stopped •... -
Page 12: Maintenance, Cleaning, Storage And Transport
Chiselling Replacing the carbon brushes • Choose a chisel appropriate for the material The carbon brushes may only be replaced by an and insert it into the tool as described in chapter authorised specialist workshop or by qualified ‚Fitting and changing tools‘. skilled personnel. -
Page 13: Troubleshooting
7. Troubleshooting Problem Possible cause Rectification The drill does not start. Damaged cable. Have the cable replaced by a service center. Fuse tripped. Check the household fuse box Carbon brushes worn out. Have the carbon brushes checked by customer service Trigger defective Have the trigger switch checked by customer service... -
Page 14: Noise And Vibrations Levels
8. Noise and vibrations Safety measures may be required to protect the operator that are based on an estimate of the levels vibration load during actual usage conditions (in this case all the parts of the operating cycle have to be considered, such as times when the power tool is turned off, and those where, the tool is Noise emission levels turned on, but is running without load). -
Page 15: Warranty
11. Warranty This warranty is void if the product is damaged, not used or maintained properly. All the instructions provided in the operating manual Warranty provided by Walter must be followed exactly for proper use of the Werkzeuge Salzburg GmbH product. -
Page 16: Service
12. Service Walter Werkzeuge Service Center E-Mail: service@walteronline.com Tel.: 00800 925 837 88 IAN 314988 Supplier: Please note that the following address is not a service centre address. Please contact the above- mentioned service centre first. Walter Werkzeuge Salzburg GmbH Gewerbeparkstr. - Page 17 Walter Werkzeuge Salzburg GmbH Gewerbeparkstr. 9 5081 Anif, Österreich V. 1.0 Last Information Update · Stan informacji · Redakcija · Stand der Informationen: 07/2019 IAN 314988...