1. Manuals
  2. Brands
  3. PSG Manuals
  4. Water Pump
  5. Wilden Original T20 Series
  6. Engineering, operation & maintenance

PSG Wilden Original T20 Series Engineering, Operation & Maintenance

Metal pumps
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
T20
E n g i n e e r i n g
O p e r a t i o n &
™
Original
Series METAL Pumps
M a i n t e n a n c e
S i m p l i f y y o u r p r o c e s s
WIL-10280-E-04
REPLACES WIL-10280-E-03

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Wilden Original T20 Series and is the answer not in the manual?

Questions and answers

Related Manuals for PSG Wilden Original T20 Series

Summary of Contents for PSG Wilden Original T20 Series

  • Page 1 E n g i n e e r i n g O p e r a t i o n & ™ Original Series METAL Pumps M a i n t e n a n c e S i m p l i f y y o u r p r o c e s s WIL-10280-E-04 REPLACES WIL-10280-E-03...

  • Page 2: C A U T I O N S - R E A D F I R S T

    C A U T I O N S – R E A D F I R S T ! WARNING: Possible explosion can result from Halogenated WARNING: Prevention of static sparking — If static sparking Hydrocarbon solvents when used in pressurized fluid systems occurs, fire or explosion could result.
  • Page 3 S e c t i o n 1 D I M E N S I O N A L D R A W I N G 102 mm (4") DIN (ANSI) LIQUID DISCHARGE 19 mm (3/4") FNPT VALVE CONNECTOR 25 mm (1") FNPT AIR EXHAUST 102 mm (4”) DIN (ANSI) LIQUID INLET...
  • Page 4 S e c t i o n 2 P E R F O R M A N C E T20 METAL T20 Metal Food Grade/Polyurethane-Fitted T20 Metal Viton ® /PTFE-Fitted RUBBER-FITTED Height ...........826 mm (32.5") Width ..........940 mm (37.0") Depth ...........330 mm (13.0") Est.

  • Page 5: S U G G E S T E D O P E R A T I O N & M A I N T E N A N C E

    S e c t i o n 4 S U G G E S T E D O P E R A T I O N & M A I N T E N A N C E INSTALLATION: Months of careful planning, study, A muffler installed on the the pump’s air exhaust will give and selection efforts can result in unsatisfactory pump quiet exhaust.
  • Page 6 S e c t i o n 5 T R O U B L E S H O O T I N G Pump will not run or runs slowly. Check to make sure all suction connections are air tight, Check air inlet screen and air filter for debris.
  • Page 7 D I S A S S E M B L Y / R E A S S E M B L Y I N S T R U C T I O N S Step 1 Start disassembly by removing the wing nuts from the ball pots. This allows the ball pot cover to be removed, exposing the discharge or inlet ball valves and ball pot lid o-rings for inspection.
  • Page 8 D I A S S E M B L Y & R E A S S E M B L Y O F I N L E T H O U S I N G DISASSEMBLY Loosen clamp band around inlet elbow. (See Figure 1A.) Remove the clamp band while supporting the elbow.
  • Page 9 D I A S S E M B L Y & R E A S S E M B L Y O F C E N T E R S E C T I O N H O U S I N G DISASSEMBLY Figure 2A Figure 2B...
  • Page 10 D I A S S E M B L Y & R E A S S E M B L Y O F C E N T E R S E C T I O N H O U S I N G Step 4 Place the center section as shown in Figure 4A.
  • Page 11 R E A S S E M B L Y O F C E N T E R S E C T I O N H O U S I N G Step 1 Prior to reassembly, remove Glyd™ rings from center block bushing and flush the center block, removing grit and contaminants.
  • Page 12 R E A S S E M B L Y O F C E N T E R S E C T I O N H O U S I N G Figure 4A Figure 5A Step 4 Step 5 Return the pump to an upright position.
  • Page 13 D I A S S E M B L Y & R E A S S E M B L Y O F D I S C H A R G E H O U S I N G DISASSEMBLY Step 1 Loosen clamp bands between ball pots and discharge tee.
  • Page 14 R E A S S E M B L Y O F P U M P B O D Y Step 1 With assistance, place the center section housing onto the inlet manifold. Replace clamp bands around the inlet elbows and ball pots and tighten per the torque specification*. Step 2 With assistance, place the discharge assembly onto the discharge elbows.
  • Page 15 S e c t i o n 6 A D I A S S E M B L Y & R E A S S E M B L Y O F A I R V A L V E / C E N T E R B L O C K The air valve assembly consists of both the air valve body and piston and the center block.

  • Page 16: E X P L O D E D V I E W & P A R T S L I S T I N G

    S e c t i o n 8 e x p l o d e d v i e w & p a r t s l i s t i n g S e c t i o n 7 E X P L O D E D V I E W &...
  • Page 17 E X P L O D E D V I E W & P A R T S L I S T I N G T20 ORIGINAL METAL P A R T S L I S T I N G T20/WWWAD ITEM DESCRIPTION QTY.

  • Page 18: Elastomer Options

    S e c t i o n 8 E L A S T O M E R O P T I O N S / T O R Q U E S P E C I F I C A T I O N S ELASTOMER OPTIONS ULTRA-FLEX ®...

  • Page 19: Warranty

    W A R R A N T Y Each and every product manufactured by Wilden Pump and Engineering, LLC is built to meet the highest standards of quality. Every pump is functionally tested to insure integrity of operation. Wilden Pump and Engineering, LLC warrants that pumps, accessories and parts manufactured or supplied by it to be free from defects in material and workmanship for a period of five (5) years from date of installation or six (6) years from date of manufacture, whichever comes first.

Table of Contents