Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Dini Argeo HLD Series
Summary of Contents for Dini Argeo HLD Series
- Page 1 LABORATORY SCALE LABORWAAGE BALANCE POUR LABORATOIRES BILANCIA DA LABORATORIO OPERATING MANUAL Industrial Weighing Systems 9 Richmond St, Picton, Ontario, Canada, K0K 2T0 www.iwsystems.ca e-mail info@iwsystems.ca HLD_V1.003_11.06_EN_DE_FR_IT...
-
Page 2: Table Of Contents
ENGLISH INDEX 1. INTRODUCTION ................................. 4 2. MAIN TECHNICAL SPECIFICATIONS ..........................4 3. INSTALLATION ................................... 5 3.1 POWER SUPPLY AND START-UP ..........................5 3.2 BATTERY POWERED ............................... 5 4. FRONT PANEL KEYS AND INDICATORS ......................... 6 5. SYMBOLS ON THE LCD DISPLAY ............................ 7 6. -
Page 3: Introduction
1. INTRODUCTION This manual was created to help you install and learn all about the functional possibilities of the HLD scale. WARNINGS The scales should be sited in a location that will not degrade the accuracy. Avoid extremes of temperature. Do not place in direct sunlight or near air conditioning vents. Avoid unsuitable tables. -
Page 4: Installation
3. INSTALLATION a) Unpack then product. b) If present (depending on the model), it is necessary to unscrew and remove the locking screw for the transportation placed under the scale, as shown in the figure below: c) Level the platform by adjusting the adjustable feet until the bubble is in the centre of the level. The stability of the platform is very important. -
Page 5: Front Panel Keys And Indicators
the mains power the internal battery will be charged. If the symbol is full the battery has a full charge. If it is half the battery is nearly discharged and empty indicates the battery should be charged. As the battery is used it may fail to hold a full charge. If the battery life becomes unacceptable then contact your distributor 4. -
Page 6: Symbols On The Lcd Display
5. SYMBOLS ON THE LCD DISPLAY The LCD display has symbols which show the indicator’s functioning status; you will find the description for each symbol below. SYMBOL FUNCTION Indicates the status of battery charging (see section 3.2) Indicates that the weight is stable. Indicates that the displayed weight is a net weight. -
Page 7: Totalisation Of The Weight
6.5 TOTALISATION OF THE WEIGHT The scale can be set to accumulate manually the weight on the scale by pressing the PRINT/M+ key (see step “AU”, chapter 7.1). The weight displayed will be stored in memory when the PRINT/M+ key is pressed and the weight is stable. The display will show "ACC 1"... -
Page 8: Sample Weight Percentile
6.7 SAMPLE WEIGHT PERCENTILE In this functioning mode, the display shows the weight expressed as a percentile, comparing it with a reference weight for which the 100 percentile has been already linked. MATCHING PROCEDURE - Put the reference weight on the scale - Press the % key when the “stable”... -
Page 9: Set-Up Environment Block Diagram
7.1 SET-UP ENVIRONMENT BLOCK DIAGRAM F1 unt Ut on, Ut oFF Ut on, Ut oFF Ut on, Ut oFF EL on, EL AU, F2 bL EL oFF, F3 CoM Printer port 232, USB P Prt, P Cont, Transmission P AUto, SETUP mode WirELE... -
Page 10: F3 Com Transmission Mode
7.4 F3 CoM TRANSMISSION MODE PRINTER PORT One will be asked to select the port to be used, press MODE to select one of the suggested values: S 232 RS232 port S USB Not used in this application. Select S 232 and press ZERO to confirm. TRANSMISSION MODE One will be asked to select the transmission mode, press MODE to select one of the suggested values: P Prt... - Page 11 CALIBRATION WEIGHTS MODEL HLD150 HLD300 HLD600 HLD1500 HLD3000 HLD6000 1° SAMPLE WEIGHT 50g 100g 200g 500g 1000g 2000g 2° SAMPLE WEIGHT 100g 200g 400g 1000g 2000g 4000g 3° SAMPLE WEIGHT 150g 300g 600g 1500g 3000g 6000g P2 CAL CALIBRATION WITH FREE SAMPLE WEIGHT By pressing ZERO it’s possible to access the calibration with free sample weight.
-
Page 12: Serial Output
8. SERIAL OUTPUT Specifications RS-232 output for the transmission of the weight data ASCII code Baud 4800 (selectable from 600 - 9600) Connector: 9 pin (female) Pin 2: RECEPTION Pin 3: TRANSMISSION Pin 5: 8.1 TRANSMISSION MODES The transmitted data format varies depending on the selected transmission mode (see section 7.4). P Prt and P Auto Totalisation Mode In the normal weighing operations when one is accumulating the weight the data format is the following:... -
Page 13: Error Messages
P CONT In this transmission mode the instrument transmits continuously the following data format depending on the functioning mode: Totalisation Mode GS for gross weight, NT for net weight, XXX.XXXX is the weight ST,GS,XXX.XXXXkg<CR><LF> <CR><LF> Counting Mode XXX.XXXX is the Number of pieces PCS:XXXXXXXXpcs<CR><LF>...
Need help?
Do you have a question about the HLD Series and is the answer not in the manual?
Questions and answers