Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Service Manual
Advertisement
Table of Contents
Related Manuals for Tektronix P6701B
Summary of Contents for Tektronix P6701B
- Page 1 99 Washington Street Melrose, MA 02176 800.517.8431 TestEquipmentDepot.com P6701B & P6703B Optical-to-Electrical Converters Instructions *P071353700* 071-3537-00...
- Page 3 P6701B & P6703B Optical-to-Electrical Converters Instructions 071-3537-00...
- Page 4 Copyright Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material.
- Page 5 product.
-
Page 7: Table Of Contents
Optional accessories ............... Installation ..................Operating basics Operating safety ................Cleaning ..................Handling ..................Optical input ................... Electrical output ................Correcting for conversion gain ............Setup ....................Specifications Warranted characteristics ............. Typical characteristics ..............Nominal characteristics ..............P6701B & P6703B Instructions... - Page 8 Table of Contents P6701B & P6703B Instructions...
-
Page 9: Important Safety Information
Be aware that condensation may occur if a unit is moved from a cold to a warm environment. Do not operate in an explosive atmosphere. Remove the input signals before Keep product surfaces clean and dry. you clean the product. P6701B & P6703B Instructions... -
Page 10: Terms In The Manual
DANGER indicates an injury hazard immediately accessible as ■ you read the marking. WARNING indicates an injury hazard not immediately accessible ■ as you read the marking. CAUTION indicates a hazard to property including the product. ■ P6701B & P6703B Instructions... -
Page 11: Compliance Information
This symbol indicates that this product complies with the applicable European Union requirements according to Directives 2012/19/EU and 2006/66/EC on waste electrical and electronic equipment (WEEE) and batteries. For information about recycling options, check the Tektronix Web. P6701B & P6703B Instructions... - Page 12 Compliance Information P6701B & P6703B Instructions...
-
Page 13: Preface
This manual contains instructions and specifications for using the P6701B, and P6703B Optical-to-Electrical Converter Probes. Related manuals For performance verification procedures, adjustment procedures, list of replaceable parts, and other service information, refer to the P6701B, P6703B, & P6723 Service Manual (070-9892-xx). P6701B & P6703B Instructions... - Page 14 Preface viii P6701B & P6703B Instructions...
-
Page 15: Getting Started
Getting started This section contains a description of the P6701B, & P6703B O/E Converters and information about features, options, accessories, and proper installation. Product description The P6701B and P6703B products are optical-to electrical (O/E) converters that convert optical communication and optical video signals into electrical signals for display on an oscilloscope. -
Page 16: Options
1103 Power Supply. Order the 1103 power supply for instruments that do not have the TekProbe Interface. Installation Before you connect the output of the P6701B and P6703B O/E Converters, determine whether or not your instrument has the TekProbe II interface. - Page 17 NOTE. Some old TDS 400 and TDS 400A series oscilloscopes always interpret the P6701B and P6703B attenuation setting as ÷ 10 and display units as V instead of mW. When you use the O/E converters, divide the measurement (or scale factor) by 10 and interpret measurements as milliwatts instead of volts.
- Page 18 Getting started P6701B & P6703B Instructions...
-
Page 19: Operating Basics
Operating basics This section presents the basic information necessary you need to know to operate the P6701B and P6703B O/E Converters. Operating safety WARNING. To avoid eye injury, wear eye protection if risk of exposure to high-intensity rays or laser radiation exists. -
Page 20: Handling
NOTE. Cleaning kits for fiber-optic connectors are available from a number of suppliers. Handling Even though the fiber-optic cable of the P6701B or P6703B O/E Converter is protected by a jacket and strain relief, the fiber-optic cable should be handled carefully at all times. -
Page 21: Optical Input
Operating basics Optical input The P6701B and P6703B O/E Converters can be connected to optical fibers with a core diameter of up to 62.5 μm through one of the FC, ST, SC, or DIN adapters. Adapter cables that aid in connecting many other popular optical connectors are also available. - Page 22 Operating basics Figure 3: P6701B typical wavelength dependent gain (25 °C) Figure 4: P6703B typical wavelength dependent gain (25 °C) If your measurement instrument is so equipped, you can automatically multiply displayed waveforms or measurements by the appropriate correction factor. Refer to your instrument manual for details.
-
Page 23: Setup
Operating basics Setup The following figures show some typical equipment setups using the P6701B and P6703B O/E Converters on instruments with and without the TekProbe interface. Figure 5: Setups with the TekProbe II interface Figure 6: Setups without the TekProbe II interface... - Page 24 Operating basics P6701B & P6703B Instructions...
-
Page 25: Specifications
Specifications The following specifications apply to a P6701B or P6703B O/E converter. The converter must have a warm-up period of at least 20 minutes and be in an environment that does not exceed the limits described below. Warranted characteristics Warranted characteristics describe guaranteed performance within tolerance limits or certain type-tested requirements. -
Page 26: Typical Characteristics
Correcting for conversion gain page 7 Optical bandwidth P6701B ≥1.0 GHz P6703B ≥1.2 GHz Rise time Peak optical signal input < 100 μW P6701B ≤475 ps P6703B ≤390 ps Aberrations ≤ ±15% peak optical signal input < 200 μW P6701B & P6703B Instructions... -
Page 27: Nominal Characteristics
500 μW average optical power input Output zero drift ≤ ± 1.5 mV with output load requirement met for ideally stable optical input, 0 to -25 °C Output load requirement 50 Ω ± 1% P6701B & P6703B Instructions... - Page 28 Specifications Nominal characteristics (cont.) P6701B & P6703B Instructions...
Need help?
Do you have a question about the P6701B and is the answer not in the manual?
Questions and answers