WilTec TIG180 Operation Manual
Hide thumbs
Also See for TIG180:
- Operation manual (11 pages) ,
- Operation manual (13 pages) ,
- Operation manual (13 pages)
Table of Contents
Advertisement
Quick Links
Operation Manual
Welding Machine – 61707/61708
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ
insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities please contact us.
© by WilTec Wildanger Technik GmbH
Seite 12
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de
Advertisement
Table of Contents
Related Manuals for WilTec TIG180
Summary of Contents for WilTec TIG180
- Page 1 Due to further developments, illustrations, functioning steps and technical data can differ insignificantly. Updating the documentation If you have suggestions for improvement or have found any irregularities please contact us. © by WilTec Wildanger Technik GmbH Seite 12 http://www.WilTec.de http://www.aoyue.eu...
- Page 2 The information contained in this document is subject to change without prior notice. No part of this document can be copied or duplicated in another form without the prior written consent of WilTec Wildanger Technik GmbH. The WilTec Wildanger Technik GmbH assumes no liability for any errors in this user manual or the connection diagram.
- Page 3 INTRODUCTION Tig180/200 are single process argon-arc welders. Outer characteristics of this welding machine are continuous current and an arc drive controlling. It has constant current characteristics: when arc voltage is normal, it guarantees that welding current will not be changed with arc length. The current will become higher and higher with arc voltage down-slope.
- Page 4 Rate work voltage(V) Driving adjustment range (A) Duty cycle No-load loss (W) Pilot arc model Efficiency Power factor 0.93 0.93 Insulation class Protection class IP21 IP21 Weight(kg) Overall Dimensions 465×265×350 465×265×350 © by WilTec Wildanger Technik GmbH Seite 15 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
-
Page 5: Installation
Input voltage must be single phase 230V. Make sure that power cable is connected to power switch or connector firmly and prevent from oxidiz- ing. Check if the power voltage is inside waved range. © by WilTec Wildanger Technik GmbH Seite 16 http://www.WilTec.de http://www.aoyue.eu... -
Page 6: Output Cable Connection
INSTALLATION PICTURE © by WilTec Wildanger Technik GmbH Seite 17 http://www.WilTec.de http://www.aoyue.eu... -
Page 7: Operation
(including between connectors and mantle, be- tween connectors and connectors). If welding machine will not be operated for longer times, it must be put into packing box and stored in dry environment. © by WilTec Wildanger Technik GmbH Seite 18 http://www.WilTec.de http://www.aoyue.eu... -
Page 8: Troubleshooting
1 mm between arc-striking tip. heard, wiping welding Switch (sticking/argon-arc welding) is damaged, replace it. can strike arc. Some of HF arc-striking circuit components are damaged; find out and replace them. © by WilTec Wildanger Technik GmbH Seite 19 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de... - Page 9 8. Sticking spatter is 1.Electrode is connected wrong; exchange grounding cable and handle much and caustic cable. electrode of is difficult. © by WilTec Wildanger Technik GmbH Seite 20 http://www.WilTec.de http://www.aoyue.eu http://www.teichtip.de...
- Page 10 All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the domestic waste.