WilTec TIG180 Operation Manual
Hide thumbs
Also See for TIG180:
- Operation manual (10 pages) ,
- Operation manual (13 pages) ,
- Operation manual (13 pages)
Advertisement
Quick Links
Operation Manual
Welding Machine
61707, 61708
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignific -
antly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
Advertisement
Related Manuals for WilTec TIG180
Summary of Contents for WilTec TIG180
- Page 1 Operation Manual Welding Machine 61707, 61708 Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignific - antly.
- Page 2 All rights reserved. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.
- Page 3 Pass the operating instructions on to third parties. Make sure that third parties use this product only after receiving the necessary instructions. © by WilTec Wildanger Technik GmbH Item 61707, 61708 Page 3 http://www.WilTec.de http://www.aoyue.eu...
- Page 4 The slag is hard and brittle after it has solidified. The slag hammer will then break it into sharp-edged particles that can dangerously injure the eyes. You should therefore protect your eyes when removing the slag with suitable protective goggles. © by WilTec Wildanger Technik GmbH Item 61707, 61708 Page 4 http://www.WilTec.de...
- Page 5 ◦ simple installation and operation Caution: The user is not permitted to dismantle, rebuild or replace electrical components himself. Oth - erwise the guarantee of the device will expire. © by WilTec Wildanger Technik GmbH Item 61707, 61708 Page 5 http://www.WilTec.de http://www.aoyue.eu...
- Page 6 Air plug Welding current adjustment Connection for electrode clip Temperature light Negative output terminal Release time adjustment MMA/TIG switch Positive output termnal 10 Digital spectrum display © by WilTec Wildanger Technik GmbH Item 61707, 61708 Page 6 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
-
Page 7: Installation
Installation picture © by WilTec Wildanger Technik GmbH Item 61707, 61708 Page 7 http://www.WilTec.de http://www.aoyue.eu... - Page 8 If the welding machine is not used for a long time, it must be packed up and stored in a dry place. © by WilTec Wildanger Technik GmbH Item 61707, 61708 Page 8 http://www.WilTec.de http://www.aoyue.eu...
-
Page 9: Troubleshooting
Abnormal indicator is lit Possibly caused by overheating protection; switch the machine but there is no welding off first, then on again after the fault indicator as has been © by WilTec Wildanger Technik GmbH Item 61707, 61708 Page 9 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de... - Page 10 Excessive weld spatter / Electrode is connected incorrectly; Replace the grounding and handle incorrect polarity of the cables. electrode © by WilTec Wildanger Technik GmbH Item 61707, 61708 Page 10 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 11 All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the domestic waste.
Need help?
Do you have a question about the TIG180 and is the answer not in the manual?
Questions and answers