Page 1 Juniper Control System (JCS) 1200 Platform Hardware Guide Juniper Networks, Inc. 1194 North Mathilda Avenue Sunnyvale, California 94089 408-745-2000 www.juniper.net Part Number: 530-023226-01, Revision 4...
Page 2 Products made or sold by Juniper Networks or components thereof might be covered by one or more of the following patents that are owned by or licensed to Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,192,051, 6,333,650, 6,359,479, 6,406,312, 6,429,706, 6,459,579, 6,493,347, 6,538,518, 6,538,899, 6,552,918, 6,567,902, 6,578,186, and 6,590,785.
Page 3 (g) distribute any key for the Software provided by Juniper to any third party; (h) use the Software in any manner that extends or is broader than the uses purchased by Customer from Juniper or an authorized Juniper reseller;...
Page 4 (or services are accessed by) the Software shall be a third party beneficiary with respect to this Agreement, and such licensor or vendor shall have the right to enforce this Agreement in its own name as if it were Juniper. In addition, certain third party software may be provided with the Software and is subject to the accompanying license(s), if any, of its respective owner(s).
Page 5 Software, whether oral or written (including any inconsistent terms contained in a purchase order), except that the terms of a separate written agreement executed by an authorized Juniper representative and Customer shall govern to the extent such terms are inconsistent or conflict with terms contained herein.
Page 7: Table Of Contents
Major Components of the JCS 1200 Platform ..........9 JCS 1200 Alarm Panel Module Overview ............12 JCS 1200 Alarm Panel Module Description ..........12 JCS 1200 Alarm Panel Module Connectors and LEDs ......12 JCS 1200 Fan Module Overview ..............14 JCS 1200 Fan Module Description ............14 JCS 1200 Fan Module LED ..............14...
Page 8 Initial Installation Chapter 3 Preparing the Site for JCS 1200 Platform Installation Overview of Preparing the Site for JCS 1200 Platform Installation ....33 Site Preparation Checklist for the JCS 1200 Platform ........33 JCS 1200 Cabinet Requirements ..............34 JCS 1200 Cabinet Size and Clearance Requirements .......34 JCS 1200 Cabinet Airflow Requirements ..........35...
Page 9 Tools Required to Install the JCS 1200 Platform Using a Mechanical Lift ....................51 Installing the JCS 1200 Platform Using a Lift ...........51 Installing the JCS 1200 Platform in a Rack Without a Lift ......54 Tools and Parts Required to Install the JCS 1200 Platform Without a Mechanical Lift .................55 Removing Components from the JCS 1200 Platform ......55...
Page 10 JCS 1200 Hardware Component Installation Guidelines ........95 JCS 1200 Platform System Reliability Guidelines ...........95 Replacing a JCS 1200 Alarm Panel Module or Module Filler ......96 Removing a JCS 1200 Alarm Panel Module or Module Filler ....96 Installing a JCS 1200 Alarm Panel Module or Module Filler .....96 Replacing a JCS 1200 Bezel ................97...
Page 11 Removing a JCS 1200 Fan Shuttle ............122 Installing a JCS 1200 Fan Shuttle ............123 Replacing a JCS 1200 Management Module or Module Filler .......124 Removing a JCS 1200 Management Module or Module Filler ....124 Installing a JCS 1200 Management Module or Module Filler ....125 Replacing a JCS 1200 Management Module Filler Tray ........127...
Page 12 Ramp Warning for the JCS 1200 Platform ........160 JCS 1200 Laser and LED Safety Guidelines and Warnings .....160 Class 1 Laser Product Warning for the JCS 1200 Platform ....160 Class 1 LED Product Warning for the JCS 1200 Platform ....161 Laser Beam Warning for the JCS 1200 Platform ......162...
Page 13 Power Requirements, Guidelines, and Specifications Site Electrical Wiring Guidelines for the JCS 1200 Platform ......189 AC Power Supply Electrical Specifications for the JCS 1200 Platform ..190 Power Consumption for an AC-Powered JCS 1200 Platform ......190 DC Power Supply Electrical Specifications for the JCS 1200 Platform ..192 Power Consumption for a DC-Powered JCS 1200 Platform ......192...
Page 14 Juniper Control System (JCS) 1200 Platform Hardware Guide Table of Contents...
Page 15 Figure 2: Straight-on Rear View of JCS 1200 Platform with AC Connectors ....................6 Figure 3: Exploded Front View of Components in the JCS 1200 Platform ..10 Figure 4: Exploded Rear View of Components in the JCS 1200 Platform ..11 Figure 5: JCS 1200 Alarm Panel Module LEDs and Connectors ......12 Figure 6: JCS 1200 Fan Module ..............15...
Page 16 Figure 65: Removing a JCS 1200 Media Tray ..........129 Figure 66: Installing a JCS 1200 Media Tray ..........129 Figure 67: Positioning the Release Lever and Button on the JCS 1200 Media Tray ......................130 Figure 68: Removing and Installing a JCS 1200 MUX Card ......131 Figure 69: Removing and Installing a JCS 1200 MUX Card ......132...
Page 17 List of Figures Figure 84: Removing and Installing a JCS 1200 Switch Module Filler Tray ..145 Figure 85: Placing a Component into an Electrostatic Bag ......154 Figure 86: JCS 1200 Declaration of Conformity ...........185 Figure 87: Serial Number ID Label ...............195 Figure 88: JCS 1200 Chassis Serial Number Label ........196...
Page 18 Juniper Control System (JCS) 1200 Platform Hardware Guide xviii List of Figures...
Page 19 Table 15: JCS 1200 Switch Module LEDs ............29 Table 16: Site Preparation Checklist ..............34 Table 17: Parts List for a Fully Configured JCS 1200 Platform .......41 Table 18: JCS 1200 Accessory Box Parts List ..........42 Table 19: Open-Frame Rack Mounting Hole Locations ........44 Table 20: Troubleshooting JCS 1200 Fan Module Problems ......87...
Page 20 Juniper Control System (JCS) 1200 Platform Hardware Guide List of Tables...
Page 21 About This Guide This preface provides the following guidelines for using the JCS 1200 Platform Hardware Guide: Objectives on page xxi Audience on page xxii Documentation Conventions on page xxii List of Technical Publications on page xxiv Obtaining Documentation on page xxxi...
Page 22: Table 1: Notice Icons
This guide is designed for network administrators who are installing and maintaining a Juniper Networks router or preparing a site for router installation. To use this guide, you need a broad understanding of networks in general, the Internet in particular, networking principles, and network configuration.
Page 23: Documentation Conventions
About This Guide Table 2: Text and Syntax Conventions Convention Description Examples Represents text that you type. To enter configuration mode, type the Bold text like this command: configure user@host> configure Fixed-width text like this Represents output that appears on the user@host>...
Page 24: List Of Technical Publications
JUNOS software with enhanced services. All documents are available at http://www.juniper.net/techpubs/ Table 6 on page xxx lists additional books on Juniper Networks solutions that you can order through your bookstore. A complete list of such books is available at http://www.juniper.net/books...
Page 25 T1600 routing node. To configure a PSD, you assign any number of Flexible PIC concentrators (FPCs) in the T-series routing platform to a pair of Routing Engines on the JCS 1200 platform. Each PSD has the same capabilities and functionality as a physical router, with its own control plane, forwarding plane, and administration.
Page 26 Juniper Control System (JCS) 1200 Platform Hardware Guide Table 3: Technical Documentation for Supported Routing Platforms (continued) Book Description Services Interfaces Provides an overview of the services interfaces functions of the JUNOS software and describes how to configure the services interfaces on the router.
Page 27 Book Description JUNOScript API Guide Describes how to use the JUNOScript application programming interface (API) to monitor and configure Juniper Networks routing platforms. JUNOS XML API Configuration Reference Provides reference pages for the configuration tag elements in the JUNOS XML API.
Page 28: Table 4: Junos Software Network Operations Guides
Table 4: JUNOS Software Network Operations Guides Book Description Baseline Describes the most basic tasks for running a network using Juniper Networks products. Tasks include upgrading and reinstalling JUNOS software, gathering basic system management information, verifying your network topology, and searching log messages.
Page 29: Table 5: Junos Software With Enhanced Services Documentation
About This Guide Table 4: JUNOS Software Network Operations Guides (continued) Book Description MPLS Describes tasks for configuring, monitoring, and troubleshooting an example MPLS network. Tasks include verifying the correct configuration of the MPLS and RSVP protocols, displaying the status and statistics of MPLS running on all routing platforms in the network, and using the layered MPLS troubleshooting model to investigate problems with an MPLS network.
Page 30: Table 6: Additional Books Available Through Http://Www.juniper.net/Books
Juniper Control System (JCS) 1200 Platform Hardware Guide Table 5: JUNOS Software with Enhanced Services Documentation (continued) Book Description J-series Only JUNOS Software with Enhanced Services Design Provides guidelines and examples for designing and and Implementation Guide implementing IPsec VPNs), firewalls, and routing on J-series Services Routers running JUNOS software with enhanced services.
Page 31: Obtaining Documentation
Provides a brief history of the Internet, explains IP addressing and routing (Routing Information for Multivendor IP Networks Protocol [RIP], OSPF, IS-IS, and Border Gateway Protocol [BGP]), explores ISP peering and routing policies, and displays configurations for both Juniper Networks and other vendors' routers. The Complete IS-IS Protocol Provides the insight and practical solutions necessary to understand the IS-IS protocol and how it works by using a multivendor, real-world approach.
Page 32 7 days a week, 365 days a year. Self-Help Online Tools and Resources For quick and easy problem resolution, Juniper Networks has designed an online self-service portal called the Customer Support Center (CSC) that provides you with the following features: Find CSC offerings: http://www.juniper.net/customers/support/...
Page 33 Part 1 Product Overview JCS 1200 Platform Overview on page 3 Hardware Component Overview on page 9 Product Overview...
Page 34 Juniper Control System (JCS) 1200 Platform Hardware Guide Product Overview...
Page 35: Jcs 1200 Platform Overview
Gigabit Ethernet links connected between control boards on the T-series platform and switch cards in the JCS 1200 chassis. Each Routing Engine (or Routing Engine pair) in the JCS 1200 comprises the control plane of a single Protected System Domain (PSD).
Page 36: Jcs 1200 Hardware Overview
A media tray that contains two universal serial bus (USB) version 2.0 ports that can be used by any Routing Engine. There are two media tray bays. Figure 1 on page 5 shows a straight-on front view of a JCS 1200 AC platform. JCS 1200 Hardware Overview...
Page 37: Figure 1: Straight-On Front View Of The Jcs 1200 Platform
Chapter 1: JCS 1200 Platform Overview Figure 1: Straight-on Front View of the JCS 1200 Platform Figure 2 on page 6 shows a straight-on rear view of a JCS 1200 AC platform with AC power connectors. JCS 1200 Hardware Overview...
Page 38: Figure 2: Straight-On Rear View Of Jcs 1200 Platform With Ac Connectors
Juniper Control System (JCS) 1200 Platform Hardware Guide Figure 2: Straight-on Rear View of JCS 1200 Platform with AC Connectors JCS 1200 Alarm Panel Module Description on page 12 Related Topics JCS 1200 Fan Module Description on page 14 JCS 1200 Management Module Description on page 15...
Page 39: Jcs 1200 Platform Features And Specifications
Redundant cooling: 500 mA maximum) 86° F (5° to 30° C) module bays (N+1 redundant) Front system LED panel JCS 1200 platform off: –40° to 70° C Security features: (–40° to 158° F). Twelve Routing Engine bays (on front): Login password for remote connection...
Page 40 Related Topics JCS 1200 Platform Environmental Specifications on page 187 AC Power Supply Electrical Specifications for the JCS 1200 Platform on page 190 Power Consumption for an AC-Powered JCS 1200 Platform on page 190 DC Power Supply Electrical Specifications for the JCS 1200 Platform on page 192...
Page 41: Hardware Component Overview
Figure 3 on page 10 and Figure 4 on page 11 show the locations of the major components in the JCS 1200 platform. These modules supply common functions to the Routing Engines that are installed in the bays in the front of the JCS 1200 platform. Major Components of the JCS 1200 Platform...
Page 42: Figure 3: Exploded Front View Of Components In The Jcs 1200 Platform
Juniper Control System (JCS) 1200 Platform Hardware Guide Figure 3: Exploded Front View of Components in the JCS 1200 Platform Major Components of the JCS 1200 Platform...
Page 43: Jcs 1200 Routing Engine Description
Figure 4: Exploded Rear View of Components in the JCS 1200 Platform NOTE: The JCS 1200 platform comes with two DC power boxes or two AC power boxes. The power boxes cannot be changed from the type that is already installed.
Page 44: Figure 5: Jcs 1200 Alarm Panel Module Leds And Connectors
JCS 1200 Alarm Panel Module Connectors and LEDs on page 12 JCS 1200 Alarm Panel Module Description The JCS 1200 platform comes with an alarm panel module that provides telecom relays and LED alarm status. You can also connect each Routing Engine to a console by connecting an external breakout cable to the serial port on the alarm panel module.
Page 45: Jcs 1200 Alarm Panel Module Connectors And Leds
FRU ready for Blue On steadily It is safe to remove the alarm panel module from the JCS 1200 removal platform. Alarm panel Amber On steadily Indicates that there is a fault on the alarm panel module. The...
Page 46: Jcs 1200 Fan Module Overview
JCS 1200 platform, which is reported by the media tray. If the ambient temperature is 77° F (25° C) or below, the JCS 1200 platform fan modules run at their minimum rotational speed. If the ambient temperature is above 77° F (25° C), the fan modules run faster, increasing their speed as required to control internal JCS 1200 platform temperature.
Page 47: Jcs 1200 Management Module Overview
JCS 1200 components. See the JUNOS Protected System Domain Configuration Guide for information about configuring the management module. You can order the JCS 1200 platform with one or two hot-swappable management modules. Install the management modules in management module bay 1 and management module bay 2 to provide redundancy.
Page 48: Jcs 1200 Management Module Connectors And Leds
Juniper Control System (JCS) 1200 Platform Hardware Guide NOTE: When you install a management module into the JCS 1200 platform, a management module interposer must be installed into the bay before installing the management module. JCS 1200 Management Module Connectors and LEDs on page 16...
Page 49: Figure 8: Jcs 1200 Management Module Leds And Controls
Figure 8: JCS 1200 Management Module LEDs and Controls The management module consists of the following components: Serial connector—Use this connection to configure and manage the JCS 1200 components over a serial line through the management module CLI. This connector provides local access to the CLI and any Routing Engine. For example,...
Page 50: Jcs 1200 Media Tray Overview
Management module Amber On steadily An error has been detected in the management module. When error this LED is lit, the JCS 1200 system error LED is also lit on the alarm panel. Ethernet Link ( Green On steadily There is an active connection through the Ethernet port to the LINK network.
Page 51: Jcs 1200 Media Tray Connectors And Leds
You can order the JCS 1200 platform with one or two hot-swappable media trays. The media trays can be installed in media tray bay 1 and media tray bay 2 to provide redundancy.
Page 52: Jcs 1200 Mux Card Description
The power subsystem, the power module, or the LED has failed. CAUTION: If the power-on LED is off, it does not mean that electrical current is not present in the JCS 1200 platform. The LED might be defective. To remove all electrical current from the JCS 1200 platform, you must disconnect all power cords from all power input connectors.
Page 53: Figure 11: Jcs 1200 Mux Card Leds
Locating the JCS 1200 MUX Card Serial Number on page 201 JCS 1200 MUX Card LEDs Figure 11 on page 21 shows the location of the LEDs on the JCS 1200 MUX card. Figure 11: JCS 1200 MUX Card LEDs The functions of the MUX card LEDs are described in Table 12 on page 21.
Page 54: Jcs 1200 Power Module Overview
Juniper Control System (JCS) 1200 Platform Hardware Guide Locating the JCS 1200 MUX Card Serial Number on page 201 JCS 1200 Power Module Overview Topics include: JCS 1200 Power Module Description on page 22 JCS 1200 Power Module LEDs on page 23 JCS 1200 Power Module Description Figure 12 on page 22 shows the AC and DC power modules.
Page 55: Figure 13: Jcs 1200 Power Module Leds
Replacing a JCS 1200 Power Box on page 134 Troubleshooting JCS 1200 Power Problems on page 89 Locating the JCS 1200 Power Module Serial Number on page 202 JCS 1200 Power Module LEDs Figure 13 on page 23 shows the LEDs on each power module.
Page 56: Figure 14: Jcs 1200 Routing Engine
JCS 1200 Routing Engine Overview Topics include: JCS 1200 Routing Engine Description on page 24 JCS 1200 Routing Engine Control Panel Buttons and LEDs on page 25 JCS 1200 Routing Engine Description Figure 14 on page 24 shows a JCS 1200 Routing Engine.
Page 57: Jcs 1200 Routing Engine Control Panel Buttons And Leds
Chapter 2: Hardware Component Overview The JCS 1200 platform provides 12 bays for Routing Engines. A Routing Engine is a hot-swappable independent server with its own processors, memory, storage, network controllers, operating system, and applications. The Routing Engine is installed in a bay in the JCS 1200 platform and shares power, fans, switches, and ports with other Routing Engines.
Page 58: Table 14: Jcs 1200 Routing Engine Leds
Powering On a JCS 1200 Routing Engine on page 73 Powering Off a JCS 1200 Routing Engine on page 74 Replacing a JCS 1200 Routing Engine on page 140 Locating the JCS 1200 Routing Engine Serial Number on page 203 JCS 1200 Routing Engine Control Panel Buttons and LEDs...
Page 59: Jcs 1200 Switch Module Overview
Figure 16 on page 27 shows the JCS 1200 switch module. Figure 16: JCS 1200 Switch Module The JCS 1200 platform supports two hot-swappable switch module bays (see “JCS 1200 Hardware Overview” on page 4 for the location of the switch module bays). You must install a switch module interposer into the bay before you install a switch module into the JCS 1200 platform.
Page 60: Figure 17: Jcs 1200 Switch Module Components
T-series routing platforms running JUNOS Release 9.2 to the JCS 1200 platform. The RJ-45 ports labeled the switch module are reserved for future use. You can use the RJ-45 port labeled to manage the switch module.
Page 61: Figure 18: Jcs 1200 Switch Module Leds
Replacing a JCS 1200 Switch Module Filler Tray on page 145 Replacing a JCS 1200 Switch Module Interposer on page 146 Replacing a JCS 1200 Switch Module or Module Filler on page 143 Locating the JCS 1200 Switch Module Serial Number on page 205...
Page 62: Jcs 1200 Power Connectors
Connect a power cord from each power connector to an appropriate power source. See “Connecting the JCS 1200 AC Platform to AC Power” on page 62 or “Connecting the JCS 1200 DC Platform to DC Power” on page 63 for more information.
Page 63: Part 2 Initial Installation
Part 2 Initial Installation Preparing the Site for JCS 1200 Platform Installation on page 33 Unpacking the JCS 1200 Platform on page 39 Installing the JCS 1200 Mounting Hardware on page 43 Installing the JCS 1200 Platform on page 49...
Page 64 Juniper Control System (JCS) 1200 Platform Hardware Guide Initial Installation...
Page 65: Preparing The Site For Jcs 1200 Platform Installation
Preparing the Site for JCS 1200 Platform Installation Topics include: Overview of Preparing the Site for JCS 1200 Platform Installation on page 33 Site Preparation Checklist for the JCS 1200 Platform on page 33 JCS 1200 Cabinet Requirements on page 34...
Page 66: Table 16: Site Preparation Checklist
800 mm deep. A cabinet larger than the minimum requirement provides better airflow and reduces the chance of overheating. To accommodate a single JCS 1200 platform, the cabinet must be at least 12 U (21 in. (53.34 cm)) high. JCS 1200 Cabinet Requirements...
Page 67 The minimum total clearance inside the cabinet is 30.70 in. between the inside of the front door and the inside of the rear door. NOTE: If you mount the JCS 1200 platform in a cabinet, be sure that sufficient room is provided for cable management and cables.
Page 68: Jcs 1200 Rack Size And Strength
Electronics Industry Association ( http://www.eia.org With the use of adapters, the JCS 1200 platform is designed to fit into a 600-mm-wide rack or cabinet , as defined in the four-part Equipment Engineering (EE); European telecommunications standard for equipment practice (document numbers ETS 300...
Page 69: Jcs 1200 Connection To Building Structure
Chapter 3: Preparing the Site for JCS 1200 Platform Installation Figure 19: Typical Open-Frame Rack Overview of Preparing the Site for JCS 1200 Platform Installation on page 33 Related Topics Site Preparation Checklist for the JCS 1200 Platform on page 33...
Page 70: Maintenance
Airflow vents provided along the sides of the chassis must remain open and uncovered for proper cooling. Figure 20: JCS 1200 Chassis Dimensions and Clearance Requirements Overview of Preparing the Site for JCS 1200 Platform Installation on page 33 Related Topics Site Preparation Checklist for the JCS 1200 Platform on page 33...
Page 71: Unpacking The Jcs 1200 Platform
Chapter 4 Unpacking the JCS 1200 Platform This chapter describes how to prepare to install the JCS 1200 platform. Topics include: Tools and Parts Required to Unpack the JCS 1200 Platform on page 39 Unpacking the JCS 1200 Platform on page 40...
Page 72 The platform is shipped in a cardboard box strapped securely to a wood pallet. Plastic straps secure the top and bottom in place. The JCS 1200 chassis is bolted to this pallet. Quick Start installation instructions and a cardboard accessory box are also included in the shipping container.
Page 73: Table 17: Parts List For A Fully Configured Jcs 1200 Platform
A fully configured JCS 1200 platform contains the JCS 1200 platform chassis with installed components, listed in Table 17 on page 41, and an accessory box, which contains the parts listed in Table 18 on page 42. The parts shipped with your JCS 1200 platform can vary.
Page 74: Table 18: Jcs 1200 Accessory Box Parts List
Juniper Networks Product Warranty End User License Agreement Accessory box, 19" x 12" x 3" Tools and Parts Required to Unpack the JCS 1200 Platform on page 39 Related Topics Unpacking the JCS 1200 Platform on page 40 Verifying Parts Received for the JCS 1200 Platform...
Page 75: Chapter 5 Installing The Jcs 1200 Mounting Hardware
Installing the JCS 1200 Mounting Hardware for an Open-Frame Rack on page 46 JCS 1200 Platform Rack-Mounting Hardware The JCS 1200 platform can be installed in a four-post rack or cabinet or an open-frame rack. Before you install the JCS 1200 platform, you install the mounting hardware on the rack.
Page 76: Cabinet
Installing the JCS 1200 Mounting Hardware for a Four-Post Rack or Cabinet If you are installing the JCS 1200 platform in a four-post rack or cabinet, you must first install the large mounting shelf, followed by the small mounting shelf.
Page 77 Tighten all the screws completely. If the rack rails require cage nuts, install cage nuts into the holes specified in “Rack Mounting Hole Locations for the JCS 1200 Platform” on page 43 for the small shelf on the rear side of the rack rails.
Page 78 Juniper Control System (JCS) 1200 Platform Hardware Guide Installing the JCS 1200 Platform Using a Lift on page 51 Lifting the JCS 1200 Platform into the Rack or Cabinet on page 56 Installing the JCS 1200 Mounting Hardware for an Open-Frame Rack on page 46...
Page 79: Figure 21: Installing The Jcs 1200 Mounting Hardware For A Four-Post Rack Or Cabinet
Rack Mounting Hole Locations for the JCS 1200 Platform on page 43 Installing the JCS 1200 Platform Using a Lift on page 51 Lifting the JCS 1200 Platform into the Rack or Cabinet on page 56 Installing the JCS 1200 Mounting Hardware for a Four-Post Rack or...
Page 80: Figure 22: Installing The Jcs 1200 Mounting Hardware For An Open-Frame Rack
Juniper Control System (JCS) 1200 Platform Hardware Guide Installing the JCS 1200 Mounting Hardware for an Open-Frame Rack...
Page 81: Installing The Jcs 1200 Platform
Platform on page 49 Installing the JCS 1200 Platform Using a Mechanical Lift on page 51 Installing the JCS 1200 Platform in a Rack Without a Lift on page 54 Safety Requirements, Warnings, and Guidelines for Installing the JCS 1200 Platform...
Page 82 Rack-Mounting Requirements and Warnings for the JCS 1200 Platform on page 156 Ramp Warning for the JCS 1200 Platform on page 160 Class 1 Laser Product Warning for the JCS 1200 Platform on page 160 Class 1 LED Product Warning for the JCS 1200 Platform on page 161...
Page 83: Tools Required To Install The Jcs 1200 Platform Using A Mechanical Lift
JCS 1200 platform using a mechanical lift. If you do not use a lift to install the JCS 1200 platform, see “Lifting the JCS 1200 Platform into the Rack or Cabinet” on page 56 for complete instructions to safely install the platform.
Page 84 JCS 1200 platform's weight and is adequately supported at the installation site. To install the JCS 1200 platform using a lift (see Figure 23 on page 53 and Figure 24 on page 54): If you are installing the platform in an open-frame rack, ensure that the rack is in its permanent location and is secured to the building.
Page 85: Installing The Jcs 1200 Platform Using A Lift
Chapter 6: Installing the JCS 1200 Platform Figure 23: Installing the JCS 1200 Platform in a Four-Post Rack Installing the JCS 1200 Platform Using a Lift...
Page 86: Installing The Jcs 1200 Platform In A Rack Without A Lift
Juniper Control System (JCS) 1200 Platform Hardware Guide Figure 24: Installing the JCS 1200 Platform in an Open-Frame Rack Tools Required to Install the JCS 1200 Platform Using a Mechanical Lift on page 51 Related Topics Installing the JCS 1200 Platform in a Rack Without a Lift Because of the JCS 1200 platform's size and weight—up to 350 lb (158.8 kg)
Page 87: Tools And Parts Required To Install The Jcs 1200 Platform Without A Mechanical Lift
Chapter 6: Installing the JCS 1200 Platform Tools and Parts Required to Install the JCS 1200 Platform Without a Mechanical Lift To install the platform, you need the following tools and parts: Phillips (+) screwdriver, number 2 ESD grounding wrist strap...
Page 88 Ensure the rack is in its permanent location and is secured to the building. Position the JCS 1200 platform in front of the rack or cabinet, centering it in front of the mounting shelves. Use a pallet jack if one is available.
Page 89: Reinstalling Components Into The Jcs 1200 Platform
NOTE: Make sure that all empty slots are covered with a blank panel before operating the JCS 1200 platform. Preventing Electrostatic Discharge Damage to the JCS 1200 Platform on page 154 Related Topics Installing a JCS 1200 Fan Module on page 118...
Page 90 Juniper Control System (JCS) 1200 Platform Hardware Guide Reinstalling Components into the JCS 1200 Platform...
Page 91: Connecting The Jcs 1200 Platform
This chapter discusses the following procedures: Before you Begin Connecting the JCS 1200 Platform on page 59 Tools and Parts Required for Connecting the JCS 1200 Platform on page 60 Supplying Power to the JCS 1200 Platform on page 60...
Page 92 CAUTION: By default, SNMP is enabled on the management module. Do not disable SNMP. If you disable SNMP, you might not be able to access the management module. Connecting the JCS 1200 Platform to a T-series Routing Platform on page 74 Related Topics...
Page 93: Jcs 1200 Platform Power Overview
Disconnecting Power from the JCS 1200 Platform on page 65 JCS 1200 Platform Power Overview The JCS 1200 platform does not have a power switch. The platform has four power connectors; each powers a power module. As viewed from the rear of the JCS 1200...
Page 94: Connecting The Jcs 1200 Ac Platform To Ac Power
Electrotechnical Commission (IEC) standard 60320. The plug at the male end of the power cord fits into the power source receptacle that is standard for your geographical location. Use the AC power cords to connect AC power to the JCS 1200 platform. To supply power to the JCS 1200 platform: Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to one of the ESD points on the chassis.
Page 95: Figure 27: Jcs 1200 Dc Power Terminal Connectors
Chapter 7: Connecting the JCS 1200 Platform The Routing Engines in the JCS 1200 platform are connected to power but are not turned on. After the JCS 1200 platform has power, depending on the configuration settings, the Routing Engines might have to be individually turned on.
Page 96: Figure 28: Attaching The Cable Lugs To The Jcs 1200 Dc Power Terminal
Attach the lugs on the DC source power cables to the terminal studs, making sure the cables are not touching or in the way of any JCS 1200 platform components. When connecting a cable lug to each stud, install a flat washer on the stud, install the cable lug, install a flat washer, install a split washer, and then install a nut (see Figure 28 on page 64).
Page 97: Disconnecting Power From The Jcs 1200 Platform
Chapter 7: Connecting the JCS 1200 Platform The Routing Engines in the JCS 1200 platform are connected to power but are not turned on. After the JCS 1200 platform has power, depending on the configuration settings, the Routing Engines might have to be individually turned on.
Page 98 CAUTION: Only trained service personnel other than Juniper Networks service technicians are authorized to make the connections to and disconnections from the –48 volt DC power source. Juniper Networks service technicians are not certified or authorized to install or remove the –48 volt power cable. The customer is responsible for ensuring that only trained service personnel install or remove the –48 volt power...
Page 99: Figure 29: Dc Power Terminal Connectors On The Jcs 1200 Platform
Disconnect all power cords on the JCS 1200 platform from the power connectors. Preventing Electrostatic Discharge Damage to the JCS 1200 Platform on page 154...
Page 100: Connecting The Jcs 1200 Management Module To The Network
Juniper Control System (JCS) 1200 Platform Hardware Guide Connecting the JCS 1200 AC Platform to AC Power on page 62 Connecting the JCS 1200 DC Platform to DC Power on page 63 Connecting the JCS 1200 Management Module to the Network The management module supports network connection through an Ethernet connector or a serial connector (see Figure 30 on page 68).
Page 101 Chapter 7: Connecting the JCS 1200 Platform Connecting to the JCS 1200 Management Module Using a Network Ethernet Connection To connect the management module to the network using the Ethernet port: Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to one of the ESD points on the chassis.
Page 102: Establishing Your Jcs 1200 Management Module Connection
Preventing Electrostatic Discharge Damage to the JCS 1200 Platform on page 154 Related Topics Tools and Parts Required for Connecting the JCS 1200 Platform on page 60 Establishing Your JCS 1200 Management Module Connection on page 70 Establishing Your JCS 1200 Management Module Connection The management module has the following default settings: IP address: 192.168.70.125...
Page 103: Establishing Your Jcs 1200 Management Module Connection Using A Direct Ethernet Connection
CLI. The following topics describe how to establish a session between a client computer and the management module to perform initial configuration of the JCS 1200 platform. Establishing Your JCS 1200 Management Module Connection Using a Direct...
Page 104: Connecting A Console To The Jcs 1200 Routing Engines
To access the Routing Engines from a console, you must use the serial port breakout cable provided with the chassis to connect the JCS 1200 platform. The breakout cable provides a direct serial interface to each Routing Engine in the JCS 1200 platform and contains 14 RJ-45 serial cable connectors (see Figure 31 on page 72).
Page 105: Powering On A Jcs 1200 Routing Engine
Powering Off a JCS 1200 Routing Engine on page 74 Powering On a JCS 1200 Routing Engine After you connect the Routing Engine to power through the JCS 1200 platform, the Routing Engine can start in any of the following ways: You can press the power control button on the front of the Routing Engine behind the control panel door (see “JCS 1200 Routing Engine Control Panel Buttons and...
Page 106: Connecting The Jcs 1200 Platform To A T-Series Routing Platform
You can connect up to three of the following T-series routing platforms running JUNOS Release 9.2 or later to the JCS 1200 platform: T320 router, T640 routing node, and T1600 routing node. The following procedures describe connecting the JCS 1200...
Page 107: Replacing The Standard Cbs In The T-Series Routing Platform
After you replace the CBs with T-CBs, you connect each T-CB on the T-series routing platform to each switch module on the JCS 1200 platform. Figure 32 on page 76 shows the location of the switch modules on the JCS 1200 platform.
Page 108: Figure 32: Location Of Switch Modules On The Jcs 1200 Platform
Juniper Control System (JCS) 1200 Platform Hardware Guide Figure 32: Location of Switch Modules on the JCS 1200 Platform To connect the T-CBs (see Figure 33 on page 77): Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to one of the ESD points on the chassis.
Page 109: Figure 33: Connecting The Jcs 1200 Platform To A T-Series Routing
Chapter 7: Connecting the JCS 1200 Platform Figure 33: Connecting the JCS 1200 Platform to a T-series Routing Platform Repeat 2 through 5 to connect up to two additional T-series routing platforms to RJ-45 ports labeled on the JCS 1200 switch module.
Page 110: Powering On The T-Series Routing Platform
CIP, monitor the startup process to verify that the system has booted properly. NOTE: You do not need to reboot the JCS 1200 platform after the routing platform has booted. Preventing Electrostatic Discharge Damage to the JCS 1200 Platform on page 154...
Page 111: Jcs 1200 Power Module Leds
After you connect the cables to the modules and route the cables, complete the following steps to start the JCS 1200 platform and verify that it is working correctly: Make sure that the following LEDs are lit, which indicate that the device is working...
Page 112 Juniper Control System (JCS) 1200 Platform Hardware Guide Verifying that the JCS 1200 Platform is Powered On Correctly...
Page 113: Configuration Guidelines
CAUTION: By default, SNMP is enabled on the management module. Do not disable SNMP. If you disable SNMP, your system might not function correctly. Perform general configuration of the JCS 1200 platform and installed components through the management module. See the JUNOS Protected System Domain Configuration Guide for information and instructions.
Page 114 Juniper Control System (JCS) 1200 Platform Hardware Guide Configuring the JCS 1200 Platform...
Page 115: Part 3 Hardware Troubleshooting And Replacement Procedures
Part 3 Hardware Troubleshooting and Replacement Procedures Troubleshooting Common JCS 1200 Platform Problems on page 85 Replacing Components in a JCS 1200 Platform on page 93 Hardware Troubleshooting and Replacement Procedures...
Page 116 Juniper Control System (JCS) 1200 Platform Hardware Guide Hardware Troubleshooting and Replacement Procedures...
Page 117: Troubleshooting Common Jcs 1200 Platform Problems
Troubleshooting Common JCS 1200 Platform Problems This chapter provides basic troubleshooting information to help you solve some common problems that might occur while you are setting up your JCS 1200 platform. Topics include: Overview of JCS 1200 Diagnostic Tools on page 85...
Page 118 Juniper Control System (JCS) 1200 Platform Hardware Guide Using Diagnostic LEDs to Diagnose Problems on the JCS 1200 Related Topics Platform on page 89 Diagnostic LEDs on the JCS 1200 Platform on page 90. JUNOS Protected System Domain Configuration Guide...
Page 119: Table 20: Troubleshooting Jcs 1200 Fan Module Problems
Make sure that all power cords are connected to a compatible power source and that the power source is working (see “Connecting the JCS 1200 AC Platform to AC Power” on page 62 or “Connecting the JCS 1200 DC Platform to DC Power”...
Page 120: Table 22: Troubleshooting Jcs 1200 Media Tray Problems
Platform on page 89 Diagnostic LEDs on the JCS 1200 Platform on page 90 Replacing a JCS 1200 Management Module or Module Filler on page 124 Troubleshooting JCS 1200 Media Tray Problems Table 22 on page 88 shows common symptoms and corrective actions for troubleshooting media tray problems.
Page 121: Light Path Diagnostic Leds
The input power and output power LEDs on the power modules are lit. If you just installed an optional device, remove it. If the JCS 1200 platform now starts, you might have installed more devices than the power modules support. You might have to install power modules in power module bays 3 and 4.
Page 122: Diagnostic Leds On The Jcs 1200 Platform
Juniper Control System (JCS) 1200 Platform Hardware Guide error LEDs on the JCS 1200 components also might be lit. These LEDs help to identify the cause of the problem. The following example shows how to use the LEDs to diagnose a system error: Note that the JCS 1200 system-fault LEDs are lit on the media tray LED panel.
Page 123 Lit LED Cause Action Major system fault When this LED is lit, the JCS 1200 platform has a Check the error log for messages. major system fault. The system can continue to Look for a lit error LED on the modules...
Page 124 Juniper Control System (JCS) 1200 Platform Hardware Guide Diagnostic LEDs on the JCS 1200 Platform...
Page 125: Replacing Components In A Jcs 1200 Platform
JCS 1200 Hardware Component Installation Guidelines on page 95 JCS 1200 Platform System Reliability Guidelines on page 95 Replacing a JCS 1200 Alarm Panel Module or Module Filler on page 96 Replacing a JCS 1200 Bezel on page 97 Replacing a JCS 1200 Bezel Collar on page 99...
Page 126 JCS 1200 platform. If you have not already done so, perform the activities on the following checklist: Set up the rack or cabinet in which you will install the JCS 1200 platform. See “JCS 1200 Platform Rack-Mounting Hardware” on page 43.
Page 127 To help ensure proper cooling and system reliability, make sure that the following requirements are met: Each of the module bays on the JCS 1200 platform has either a module or a module filler installed. Each of the Routing Engine bays on the front of the JCS 1200 platform has either a Routing Engine or a Routing Engine filler installed.
Page 128: Removing A Jcs 1200 Alarm Panel Module Or Module Filler
Replacing a JCS 1200 Alarm Panel Module or Module Filler Topics include: Removing a JCS 1200 Alarm Panel Module or Module Filler on page 96 Installing a JCS 1200 Alarm Panel Module or Module Filler on page 96 Removing a JCS 1200 Alarm Panel Module or Module Filler Figure 34 on page 96 shows how to remove and install an alarm panel module.
Page 129: Replacing A Jcs 1200 Bezel
Installing a JCS 1200 Bezel on page 98 Removing a JCS 1200 Bezel If the JCS 1200 bezel option is installed on your JCS 1200 platform, you must first remove the bezel to access any devices installed into the front of your JCS 1200 platform.
Page 130: Figure 36: Removing A Jcs 1200 Bezel
ESD points on the chassis. Hold the bezel and press the blue release button on each side of the bezel. Pull the bezel away from the JCS 1200 platform. If you are instructed to return the bezel, follow all packaging instructions and use any packaging materials for shipping that are supplied to you.
Page 131: Replacing A Jcs 1200 Bezel Collar
Holding the sides of the bezel, orient the bezel so the logo is at the top and right corner. Place the bottom edge of the bezel on the bezel retention tab. Rotate the top of the bezel toward the JCS 1200 platform until the bezel clicks into place. Turn the quarter-turn bezel locks to the locked position.
Page 132: Figure 38: Removing And Installing The Jcs 1200 Bezel Collar
Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to one of the ESD points on the chassis. Remove the bezel. See “Removing a JCS 1200 Bezel Filter” on page 107 for more information.
Page 133: Figure 39: Removing The Light Path Extension Assembly
Slide the interposer out of the bay. Remove any switch modules or module fillers from switch module bays 7 and 8. See “Removing a JCS 1200 Switch Module or Module Filler” on page 143 for more information. Remove the interposer from switch module bays 7 and 8: Pull the switch module interposer release handle to the open position.
Page 134: Figure 40: Removing The Cable Management Trays
JCS 1200 platform. Remove the bezel collar by lifting up the bezel collar and then pulling the bezel collar away from the JCS 1200 platform. Remove the cable management trays by using a Phillips-head screwdriver to remove the M4 screws that secure each tray to the bezel.
Page 135: Figure 41: Removing And Installing The Jcs 1200 Bezel Collar
Chapter 10: Replacing Components in a JCS 1200 Platform Figure 41: Removing and Installing the JCS 1200 Bezel Collar To install a JCS 1200 bezel collar (see Figure 41 on page 103): Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to one of the ESD points on the chassis.
Page 136: Figure 42: Attaching The Cable Management Trays To The Bezel Collar
Slide the interposer out of the bay. Remove any switch modules or module fillers from switch module bays 7 and 8. See “Removing a JCS 1200 Switch Module or Module Filler” on page 143 for more information. Installing a JCS 1200 Bezel Collar...
Page 137: Figure 43: Securing The Cable Management Trays
0.25 in. (0.6 cm). Slide the interposer out of the bay. Attach the bezel collar to the JCS 1200 platform (see Figure 38 on page 100): Insert the lower bezel collar hooks into the bezel mounting slots on the bottom of the JCS 1200 platform;...
Page 138: Figure 44: Installing The Light Path Extension Assembly
Install the light path extension assembly. Two light path extension assemblies are shipped with the JCS 1200 bezel to extend the light path LEDs so that they are visible through the bezel. Install one light path extension assembly for each of the management modules installed in your JCS 1200 platform.
Page 139: Replacing A Jcs 1200 Bezel Filter
Chapter 10: Replacing Components in a JCS 1200 Platform Preventing Electrostatic Discharge Damage to the JCS 1200 Platform on page 154 Related Topics Replacing a JCS 1200 Bezel Filter Topics include: Removing a JCS 1200 Bezel Filter on page 107...
Page 140: Figure 46: Removing The Air Filter Assembly
Juniper Control System (JCS) 1200 Platform Hardware Guide Remove the air filter assembly from the filter frame by pulling out and rotating the air filter assembly locks until they no longer engage the air filter assembly. Figure 46: Removing the Air Filter Assembly Remove the air filter assembly;...
Page 141: Figure 47: Cutouts On The Jcs 1200 Bezel Filter
Chapter 10: Replacing Components in a JCS 1200 Platform Figure 47: Cutouts on the JCS 1200 Bezel Filter Lay the new filter on a clean flat surface and orient it so that the cutouts for the light path extension assemblies are to the right and the large cutout at the bottom of the filter is closest to you.
Page 142: Replacing Jcs 1200 Cable Management Trays Without A Bezel
Juniper Control System (JCS) 1200 Platform Hardware Guide Figure 48: Securing the Air Filter Assembly Install the bezel on the JCS 1200 platform (see “Installing a JCS 1200 Bezel” on page 98). Preventing Electrostatic Discharge Damage to the JCS 1200 Platform on page 154...
Page 143: Figure 49: Removing And Installing The Jcs 1200 Cable Management
Figure 49: Removing and Installing the JCS 1200 Cable Management Trays The cable management trays can be removed with or without the JCS 1200 bezel. If you are removing the JCS 1200 bezel, see “Removing a JCS 1200 Bezel” on page 97 more information.
Page 144: Figure 50: Removing And Installing The Jcs 1200 Cable Management
Juniper Control System (JCS) 1200 Platform Hardware Guide Figure 50: Removing and Installing the JCS 1200 Cable Management Trays The cable management trays can be installed with or without the JCS 1200 bezel option. If you are installing the JCS 1200 bezel, see “Installing a JCS 1200 Bezel”...
Page 145: Replacing A Jcs 1200 Chassis
Disengage the following components from the JCS 1200 midplane using the procedure indicated: NOTE: Make sure each component is pulled out of the JCS 1200 platform at least 1 in. (2.54 cm). Routing Engines: Pull the two release handles on each Routing Engine to the open position (see “Removing a JCS 1200 Routing Engine”...
Page 146 Juniper Control System (JCS) 1200 Platform Hardware Guide Remove the upper and lower power boxes from the rear of the JCS 1200 chassis (see “Removing a JCS 1200 Power Box” on page 134). If you are instructed to return the chassis, follow all packaging instructions and use any packaging materials for shipping that are supplied to you.
Page 147: Replacing A Jcs 1200 Dc Terminal Cover
Engine” on page 74). Turn off the power source. NOTE: After you disconnect the JCS 1200 platform from power, wait at least 5 seconds before you connect the JCS 1200 platform to power again. Remove the two Phillips-head screws that attach the terminal cover to the DC power box.
Page 148: Replacing A Jcs 1200 Fan Module
Figure 52: Removing and Installing a JCS 1200 DC Terminal Cover To install a DC terminal cover on a JCS 1200 DC platform (see Figure 52 on page 116): Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to one of the ESD points on the chassis.
Page 149: Figure 53: Removing And Installing A Jcs 1200 Fan Module
Chapter 10: Replacing Components in a JCS 1200 Platform Figure 53: Removing and Installing a JCS 1200 Fan Module NOTE: While the JCS 1200 platform is operating, only one fan module should be removed at a time. Removing two fan modules might cause the JCS 1200 platform to overheat.
Page 150: Figure 55: Removing And Installing A Jcs 1200 Fan Module
Juniper Control System (JCS) 1200 Platform Hardware Guide NOTE: When the JCS 1200 platform is shipped, each fan module has a shipping block installed below the release lever that is on the same side as the fan module orientation mark.
Page 151: Figure 56: Fan Module Orientation Marks
Slide the fan module into the bay until it stops. NOTE: Make sure the release levers for the fan module return to a locked position. If you are shipping the JCS 1200 platform to another location, install the shipping block that came with the JCS 1200 platform.
Page 152: Replacing A Jcs 1200 Fan Pack
Juniper Control System (JCS) 1200 Platform Hardware Guide Install the Phillips-head screw that attaches the shipping block to the JCS 1200 platform. Preventing Electrostatic Discharge Damage to the JCS 1200 Platform on page 154 Related Topics JCS 1200 Fan Module Description on page 14...
Page 153: Replacing A Jcs 1200 Fan Shuttle
Slide the fan pack into position on the power module until it stops and locks into place. Rotate the power module handle to the open position. Install the power module. Preventing Electrostatic Discharge Damage to the JCS 1200 Platform on page 154 Related Topics Replacing a JCS 1200 Fan Shuttle Topics include:...
Page 154: Figure 60: Removing And Installing A Jcs 1200 Fan Shuttle
JCS 1200 platform and remove the power cables. Disconnect the cables from the modules in the rear of JCS 1200 platform. Remove any of the following modules that are installed in the rear of the JCS 1200 platform: Fan modules (see “Removing a JCS 1200 Fan Module”...
Page 155: Figure 61: Removing And Installing A Jcs 1200 Fan Shuttle
Chapter 10: Replacing Components in a JCS 1200 Platform Loosen the captive thumbscrews on the release handles, and pull the handles to the open position. The fan shuttle moves out of the JCS 1200 chassis approximately 0.5 in. (1.3 cm).
Page 156: Replacing A Jcs 1200 Management Module Or Module Filler
Orient the fan shuttle so that fan module bays 1 and 3 are above fan module bays 2 and 4. Align the shuttle with the JCS 1200 chassis and push the shuttle into the chassis until it stops. Push the release handles to the closed position. The shuttle moves back fully into the JCS 1200 chassis.
Page 157: Figure 62: Removing And Installing A Jcs 1200 Management Module
When you remove a management module, keep in mind the following: These instructions assume that the JCS 1200 platform is connected to power. If you are replacing the only management module in the JCS 1200 platform and the management module is functioning, save the configuration file before you proceed.
Page 158: Replacing A Jcs 1200 Management Module Filler Tray
Push the management module release handle to the closed position. Connect any cables to the management module. If the JCS 1200 platform is connected to power, make sure that the LED on the management module is lit. If the management module is redundant, wait at least 45 minutes for the modules to copy the configuration data before you make any changes to the management module configuration.
Page 159: Removing A Jcs 1200 Management Module Filler Tray
ESD points on the chassis. Remove the management module or filler from the management module bay (see “Removing a JCS 1200 Management Module or Module Filler” on page 124). Pull the management module filler tray release handle to the open position. The filler tray moves out of the bay approximately 0.25 in.
Page 160: Replacing A Jcs 1200 Management Module Interposer
If the management module interposer requires replacement, you must replace the entire chassis. For instructions on replacing the chassis, see “Replacing a JCS 1200 Chassis” on page 113. Replacing a JCS 1200 Chassis on page 113...
Page 161: Figure 65: Removing A Jcs 1200 Media Tray
Chapter 10: Replacing Components in a JCS 1200 Platform Figure 65: Removing a JCS 1200 Media Tray To remove a media tray (see Figure 65 on page 129): Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to one of the ESD points on the chassis.
Page 162: Replacing A Jcs 1200 Midplane
Make sure that the media tray release lever is in the open position and the compact flash release buttons are pushed into the in position. Figure 67: Positioning the Release Lever and Button on the JCS 1200 Media Tray Slide the media tray into position until it stops and locks into place.
Page 163: Replacing A Jcs 1200 Mux Card
Removing a JCS 1200 MUX Card Figure 68 on page 131 shows how to remove and install a multiplexer (MUX) card. Figure 68: Removing and Installing a JCS 1200 MUX Card To remove a MUX card (see Figure 68 on page 131): Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to one of the ESD points on the chassis.
Page 164: Replacing A Jcs 1200 Network Clock Filler
Slide the MUX card into the bay until it stops. Push the release handle to the closed position. Preventing Electrostatic Discharge Damage to the JCS 1200 Platform on page 154 Related Topics JCS 1200 MUX Card LEDs on page 21...
Page 165: Figure 70: Removing And Installing A Jcs 1200 Network Clock Filler
Chapter 10: Replacing Components in a JCS 1200 Platform Figure 70: Removing and Installing a JCS 1200 Network Clock Filler To remove a network clock filler (see Figure 70 on page 133): Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to one of the ESD points on the chassis.
Page 166: Replacing A Jcs 1200 Power Box
Slide the network clock filler into the module bay until it stops. Push the release handle to the closed position. Preventing Electrostatic Discharge Damage to the JCS 1200 Platform on page 154 Related Topics Replacing a JCS 1200 Power Box...
Page 167: Figure 72: Removing And Installing A Jcs 1200 Power Box
Disconnect the power from the JCS 1200 platform (see “Disconnecting Power from the JCS 1200 Platform” on page 65). Remove the fan shuttle from the JCS 1200 platform (see “Removing a JCS 1200 Fan Shuttle” on page 122). Remove the five Phillips-head screws that attach the power box to the chassis.
Page 168: Figure 74: Loosening Thumbscrews On The Lower Power Box
Juniper Control System (JCS) 1200 Platform Hardware Guide Figure 74: Loosening Thumbscrews on the Lower Power Box Slide the power box away from the JCS 1200 platform. If you are instructed to return the power box, follow all packaging instructions and use any packaging materials for shipping that are supplied to you.
Page 169: Figure 76: Tightening Thumbscrews On The Upper Power Box
Figure 77: Tightening Thumbscrews on the Lower Power Box Install the five Phillips-head screws that attach the power box to the chassis. Install the fan shuttle into the JCS 1200 platform (see “Installing a JCS 1200 Fan Shuttle” on page 123).
Page 170: Replacing A Jcs 1200 Power Module
Juniper Control System (JCS) 1200 Platform Hardware Guide Preventing Electrostatic Discharge Damage to the JCS 1200 Platform on page 154 Related Topics Replacing a JCS 1200 Power Module Topics include: Removing a JCS 1200 Power Module on page 138 Installing a JCS 1200 Power Module on page 139 Removing a JCS 1200 Power Module Figure 78 on page 138 shows how to remove and install a power module.
Page 171: Figure 79: Removing And Installing A Jcs 1200 Power Module
For the lower power module bays, the rear connector on the power module must be facing up. Preventing Electrostatic Discharge Damage to the JCS 1200 Platform on page 154 Related Topics JCS 1200 Power Module Description on page 22...
Page 172: Replacing A Jcs 1200 Routing Engine
Figure 80: Removing and Installing a JCS 1200 Routing Engine CAUTION: To maintain proper system cooling, do not operate the JCS 1200 platform without a Routing Engine or Routing Engine filler installed in each bay. When you remove the Routing Engine, note the bay number. Reinstalling a Routing Engine into a different bay from the one from which it was removed could have unintended consequences.
Page 173: Figure 81: Removing And Installing A Jcs 1200 Routing Engine
Installing a JCS 1200 Routing Engine Figure 81 on page 141 shows how to remove and install a Routing Engine. Figure 81: Removing and Installing a JCS 1200 Routing Engine CAUTION: Hazardous energy is present when the Routing Engine is connected to the power source.
Page 174 To help ensure proper cooling, performance, and system reliability, make sure that each Routing Engine bay on the front of the JCS 1200 platform contains a Routing Engine, expansion unit, or Routing Engine filler. Do not operate a JCS 1200 platform for more than 1 minute without a Routing Engine, expansion unit, or Routing Engine filler in each Routing Engine bay.
Page 175: Replacing A Jcs 1200 Switch Module Or Module Filler
Replacing a JCS 1200 Switch Module or Module Filler Topics include: Removing a JCS 1200 Switch Module or Module Filler on page 143 Installing a JCS 1200 Switch Module or Module Filler on page 143 Removing a JCS 1200 Switch Module or Module Filler Figure 82 on page 143 shows how to remove and install a switch module.
Page 176: Figure 83: Removing And Installing A Jcs 1200 Switch Module
Juniper Control System (JCS) 1200 Platform Hardware Guide Figure 83: Removing and Installing a JCS 1200 Switch Module The JCS 1200 platform ships with one switch module. You can install a second switch module for redundancy. To install a switch module (see Figure 83 on page 144): Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to one of the ESD points on the chassis.
Page 177: Replacing A Jcs 1200 Switch Module Filler Tray
Figure 84 on page 145 shows how to remove and install a switch module filler tray. Figure 84: Removing and Installing a JCS 1200 Switch Module Filler Tray To remove a switch module filler tray (see Figure 84 on page 145): Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to one of the ESD points on the chassis.
Page 178: Replacing A Jcs 1200 Switch Module Interposer
ESD points on the chassis. Remove the switch module filler and filler tray, if one is installed (see “Removing a JCS 1200 Switch Module or Module Filler” on page 143 and “Removing a JCS 1200 Switch Module Filler Tray” on page 145).
Page 179 Part 4 Appendixes Safety and Regulatory Compliance Information on page 149 Environmental Specifications on page 187 Power Requirements, Guidelines, and Specifications on page 189 Contacting Customer Support and Returning Hardware on page 195 Cable Connector Pinouts on page 211 Appendixes...
Page 180 Juniper Control System (JCS) 1200 Platform Hardware Guide Appendixes...
Page 181: Appendix A Safety And Regulatory Compliance Information
Appendix A Safety and Regulatory Compliance Information To install and use the JCS 1200 platform safely, follow proper safety procedures. This appendix discusses the following safety and regulatory compliance information: Definition of Safety Warning Levels on page 149 JCS 1200 Safety Guidelines and Warnings on page 150...
Page 182: Jcs 1200 General Safety Guidelines And Warnings
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanligt förfarande för att förebygga skador. General Safety Guidelines and Warnings for the JCS 1200 Platform on page 151 Related Topics JCS 1200 Safety Guidelines and Warnings...
Page 183: Jcs 1200 General Safety Guidelines And Warnings
The list of guidelines might not address all potentially hazardous situations in your working environment, so be alert and exercise good judgment at all times. General Safety Guidelines and Warnings for the JCS 1200 Platform on page 151 Qualified Personnel Warning for the JCS 1200 Platform on page 152...
Page 184: Platform
Definition of Safety Warning Levels on page 149 Related Topics Restricted Access Area Warning for the JCS 1200 Platform WARNING: The routing platform is intended for installation in restricted access areas. A restricted access area is an area to which access can be gained only by service...
Page 185 Varning! Denna enhet är avsedd för installation i områden med begränsat tillträde. Ett område med begränsat tillträde får endast tillträdas av servicepersonal med ett speciellt verktyg, lås och nyckel, eller annan säkerhetsanordning, och kontrolleras av den auktoritet som ansvarar för området. Restricted Access Area Warning for the JCS 1200 Platform...
Page 186: Figure 85: Placing A Component Into An Electrostatic Bag
Definition of Safety Warning Levels on page 149 Related Topics Preventing Electrostatic Discharge Damage to the JCS 1200 Platform Many routing platform hardware components are sensitive to damage from static electricity. Some components can be impaired by voltages as low as 30 V. You can easily generate potentially damaging static voltages whenever you handle plastic or foam packing material or if you move components across plastic or carpets.
Page 187 Before moving the platform, read the guidelines in “Overview of Preparing the Site for JCS 1200 Platform Installation” on page 33 to verify that the intended site meets the specified power, environmental, and clearance requirements.
Page 188: Rack-Mounting Requirements And Warnings For The Jcs 1200 Platform
Juniper Control System (JCS) 1200 Platform Hardware Guide Installation Instructions Power Warning for the JCS 1200 Platform WARNING: Read the installation instructions before you connect the routing platform to a power source. Waarschuwing Raadpleeg de installatie-aanwijzingen voordat u het systeem met de voeding verbindt.
Page 189 Les directives ci-dessous sont destinées à assurer la protection du personnel: Le rack sur lequel est monté le Juniper Networks router doit être fixé à la structure du bâtiment. Si cette unité constitue la seule unité montée en casier, elle doit être placée dans le bas.
Page 190 Le seguenti direttive vengono fornite per garantire la sicurezza personale: Il Juniper Networks router deve essere installato in un telaio, il quale deve essere fissato alla struttura dell'edificio. Questa unità deve venire montata sul fondo del supporto, se si tratta dell'unica unità...
Page 191 JCS 1200 Platform Rack-Mounting Hardware on page 43 Installing the JCS 1200 Mounting Hardware for a Four-Post Rack or Cabinet on page 44 Installing the JCS 1200 Mounting Hardware for an Open-Frame Rack on page 46 Rack-Mounting Requirements and Warnings for the JCS 1200 Platform...
Page 192: Ramp Warning For The Jcs 1200 Platform
Related Topics Installing the JCS 1200 Platform Using a Lift on page 51 Lifting the JCS 1200 Platform into the Rack or Cabinet on page 56 JCS 1200 Laser and LED Safety Guidelines and Warnings Single-mode Physical Interface Cards (PICs) are equipped with laser transmitters, which are considered a Class 1 Laser Product by the U.S.
Page 193: Class 1 Led Product Warning For The Jcs 1200 Platform
Definition of Safety Warning Levels on page 149 Related Topics Class 1 LED Product Warning for the JCS 1200 Platform on page 161 Laser Beam Warning for the JCS 1200 Platform on page 162 Radiation from Open Port Apertures Warning for the JCS 1200...
Page 194 Definition of Safety Warning Levels on page 149 Related Topics Class 1 Laser Product Warning for the JCS 1200 Platform on page 160 Laser Beam Warning for the JCS 1200 Platform on page 162 Radiation from Open Port Apertures Warning for the JCS 1200...
Page 195: Radiation From Open Port Apertures Warning For The Jcs 1200 Platform
Definition of Safety Warning Levels on page 149 Related Topics Class 1 Laser Product Warning for the JCS 1200 Platform on page 160 Class 1 LED Product Warning for the JCS 1200 Platform on page 161 Laser Beam Warning for the JCS 1200 Platform on page 162...
Page 196: Jcs 1200 Maintenance And Operational Safety Guidelines And Warnings
JCS 1200 Maintenance and Operational Safety Guidelines and Warnings As you maintain the platform, observe the following guidelines and warnings: Battery Handling Warning for the JCS 1200 Platform on page 164 Jewelry Removal Warning for the JCS 1200 Platform on page 165...
Page 197: Jewelry Removal Warning For The Jcs 1200 Platform
Definition of Safety Warning Levels on page 149 Related Topics Jewelry Removal Warning for the JCS 1200 Platform on page 165 Lightning Activity Warning for the JCS 1200 Platform on page 166 Operating Temperature Warning for the JCS 1200 Platform on page 167...
Page 198: Lightning Activity Warning For The Jcs 1200 Platform
Definition of Safety Warning Levels on page 149 Related Topics Battery Handling Warning for the JCS 1200 Platform on page 164 Lightning Activity Warning for the JCS 1200 Platform on page 166 Operating Temperature Warning for the JCS 1200 Platform on page 167...
Page 199: Operating Temperature Warning For The Jcs 1200 Platform
Definition of Safety Warning Levels on page 149 Related Topics Battery Handling Warning for the JCS 1200 Platform on page 164 Jewelry Removal Warning for the JCS 1200 Platform on page 165 Operating Temperature Warning for the JCS 1200 Platform on page 167...
Page 200: Product Disposal Warning For The Jcs 1200 Platform
40° C. Para evitar a restrição à circulação de ar, deixe pelo menos um espaço de 15,2 cm à volta das aberturas de ventilação. ¡Atención! Para impedir que un encaminador de la serie Juniper Networks router se recaliente, no lo haga funcionar en un área en la que se supere la temperatura ambiente máxima recomendada de 40°...
Page 201: Jcs 1200 Electrical Safety Guidelines And Warnings
In Case of an Electrical Accident on page 169 JCS 1200 General Electrical Safety Guidelines and Warnings on page 170 JCS 1200 AC Power Electrical Safety Guidelines and Warnings on page 174 JCS 1200 DC Power Electrical Safety Guidelines and Warnings on page 175...
Page 202: Jcs 1200 General Electrical Safety Guidelines And Warnings
Many routing platform components can be removed and replaced without powering off or disconnecting power to the routing platform, as detailed in “JCS 1200 Hardware Component Installation Guidelines” on page 95. Never install equipment if it appears damaged.
Page 203 General Electrical Safety Guidelines and Warnings Electrical Codes for the Related Topics JCS 1200 Platform on page 170 Midplane Energy Hazard Warning for the JCS 1200 Platform on page 172 Multiple Power Supplies Disconnection Warning for the JCS 1200 Platform on page 172...
Page 204 General Electrical Safety Guidelines and Warnings Electrical Codes for the Related Topics JCS 1200 Platform on page 170 Grounded Equipment Warning for the JCS 1200 Platform on page 171 Multiple Power Supplies Disconnection Warning for the JCS 1200 Platform on page 172...
Page 205 JCS 1200 Platform on page 170 Grounded Equipment Warning for the JCS 1200 Platform on page 171 Midplane Energy Hazard Warning for the JCS 1200 Platform on page 172 TN Power Warning for the JCS 1200 Platform on page 173...
Page 206: Jcs 1200 Ac Power Electrical Safety Guidelines And Warnings
JCS 1200 Platform on page 170 Grounded Equipment Warning for the JCS 1200 Platform on page 171 Midplane Energy Hazard Warning for the JCS 1200 Platform on page 172 Multiple Power Supplies Disconnection Warning for the JCS 1200 Platform on page 172...
Page 207: Jcs 1200 Dc Power Electrical Safety Guidelines And Warnings
DC Power Wiring Terminations Warning for the JCS 1200 Platform on page 180 JCS 1200 DC Power Electrical Safety Guidelines The following guidelines are provided for connecting a 60-A JCS 1200 platform to a –48 V DC power source: The power source must have a minimum of 80 A overcurrent protection. See article 240, paragraph 3, table 310-16 of the National Electric Code for more information about electrical wiring requirements.
Page 208 Juniper Control System (JCS) 1200 Platform Hardware Guide The JCS 1200 platform requires a DC wire rating of 4 AWG (circular mil area of 33100-52600) and of 90° C. NOTE: The actual wire gauge and ring terminal are determined by the current draw and the length of wire run or as specified by the customer premises guidelines.
Page 209 Connecting the JCS 1200 DC Platform to DC Power on page 63 Site Electrical Wiring Guidelines for the JCS 1200 Platform on page 189 DC Power Supply Electrical Specifications for the JCS 1200 Platform on page 192 Power Consumption for a DC-Powered JCS 1200 Platform on page 192...
Page 210 The grounding conductor is a separately derived system at the supply transformer or motor generator set.“DC Power Supply Electrical Specifications for the JCS 1200 Platform” on page 192 For further information, see .“DC Power Supply Electrical Specifications for the JCS 1200 Platform”...
Page 211 Appendix A: Safety and Regulatory Compliance Information DC Power Wiring Sequence Warning for the JCS 1200 Platform WARNING: Wire the DC power supply using the appropriate lugs. When connecting power, the proper wiring sequence is ground to ground, +RTN to +RTN, then –48 V to –48 V.
Page 212 Connecting the JCS 1200 DC Platform to DC Power on page 63 Site Electrical Wiring Guidelines for the JCS 1200 Platform on page 189 DC Power Supply Electrical Specifications for the JCS 1200 Platform on page 192 Power Consumption for a DC-Powered JCS 1200 Platform on page 192...
Page 213: Jcs 1200 Agency Approvals And Compliance Statements
Connecting the JCS 1200 DC Platform to DC Power on page 63 Site Electrical Wiring Guidelines for the JCS 1200 Platform on page 189 DC Power Supply Electrical Specifications for the JCS 1200 Platform on page 192 Power Consumption for a DC-Powered JCS 1200 Platform on page 192...
Page 214 The battery return connection is to be treated as a Common DC return (i.e. DC-C), as defined in GR-1089-CORE. Compliance Statements for Environmental Requirements for the JCS 1200 Related Topics Platform on page 183 Electronic Emission Notices for the JCS 1200 Platform on page 183 Agency Approvals for the JCS 1200 Platform...
Page 215: Compliance Statements For Environmental Requirements For The Jcs 1200 Platform
Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Juniper Networks is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment.
Page 216 Juniper Networks cannot accept responsibility for any failure to satisfy the protection requirements resulting from a nonrecommended modification of the product, including the fitting of non-Juniper Networks option cards. This product has been tested and found to comply with the limits for Class A Information Technology Equipment according to CISPR 22/European Standard EN 55022.
Page 217: Figure 86: Jcs 1200 Declaration Of Conformity
Japanese Voluntary Control Council for Interference (VCCI) Statement JCS 1200 Declaration of Conformity Figure 86: JCS 1200 Declaration of Conformity Agency Approvals for the JCS 1200 Platform on page 181 Related Topics Electronic Emission Notices for the JCS 1200 Platform...
Page 218 Juniper Control System (JCS) 1200 Platform Hardware Guide Compliance Statements for Environmental Requirements for the JCS 1200 Platform on page 183 Electronic Emission Notices for the JCS 1200 Platform...
Page 219: Appendix B Environmental Specifications
Appendix B Environmental Specifications JCS 1200 Platform Environmental Specifications on page 187 JCS 1200 Platform Environmental Specifications Table 25 on page 187 specifies the environmental specifications required for normal platform operation. In addition, the site should be as dust-free as possible. Dust can clog air intake vents, reducing cooling system efficiency.
Page 220 110-18 of the National Electrical Code, ANSI/NFPA 70. For additional safety guidelines and requirements, see “Safety Requirements, Warnings, and Guidelines for Installing the JCS 1200 Platform” on page 49. Compliance Statements for Environmental Requirements for the JCS 1200 Related Topics...
Page 221: Site Electrical Wiring Guidelines For The Jcs 1200 Platform
Site Electrical Wiring Guidelines for the JCS 1200 Platform on page 189 AC Power Supply Electrical Specifications for the JCS 1200 Platform on page 190 Power Consumption for an AC-Powered JCS 1200 Platform on page 190 DC Power Supply Electrical Specifications for the JCS 1200 Platform on page 192...
Page 222: Table 26: Ac Power Electrical Specifications For The Jcs 1200 Platform
AC Power Supply Electrical Specifications for the JCS 1200 Platform on page 190 Related Topics Power Consumption for an AC-Powered JCS 1200 Platform on page 190...
Page 223: Table 27: Ac-Powered Base Jcs 1200 Platform Power Requirements
Site Electrical Wiring Guidelines for the JCS 1200 Platform on page 189 Related Topics AC Power Supply Electrical Specifications for the JCS 1200 Platform on page 190 Connecting the JCS 1200 AC Platform to AC Power on page 62 Power Consumption for an AC-Powered JCS 1200 Platform...
Page 224: Table 29: Dc Power Electrical Specifications For The Jcs 1200 Platform
Operating range: –40 to –60 VDC DC input current rating 204 A @ –38 VDC Site Electrical Wiring Guidelines for the JCS 1200 Platform on page 189 Related Topics Power Consumption for a DC-Powered JCS 1200 Platform on page 192...
Page 225: Table 31: Dc-Powered Jcs 1200 Platform Component Power Requirements
51 W (approximate) 1.1 A (approximate) Site Electrical Wiring Guidelines for the JCS 1200 Platform on page 189 Related Topics DC Power Supply Electrical Specifications for the JCS 1200 Platform on page 192 Power Consumption for a DC-Powered JCS 1200 Platform...
Page 226: Table 32: Jcs 1200 Alarm Panel Interface Connector Electrical
Connecting the JCS 1200 DC Platform to DC Power on page 63 JCS 1200 Alarm Panel Module Interface Connector Electrical Specifications Table 32 on page 194 lists the electrical specifications for the JCS 1200 alarm panel interface connector. Table 32: JCS 1200 Alarm Panel Interface Connector Electrical Specifications...
Page 227: Figure 87: Serial Number Id Label
Platform on page 208 Packing the JCS 1200 Platform for Shipment on page 208 Guidelines for Packing JCS 1200 Platform Components for Shipment on page 209 Locating Component Serial Numbers Before contacting Juniper Networks, Inc. to request a Return Materials Authorization (RMA), you must find the serial number on the platform or component.
Page 228: Locating The Jcs 1200 Power Module Serial Number
(see Figure 88 on page 196). Figure 88: JCS 1200 Chassis Serial Number Label Record information about your JCS 1200 platform in Table 33 on page 196. You will need this information for future reference.
Page 229: Figure 89: Jcs 1200 Alarm Panel Module Serial Number Label
JCS 1200 Return Procedure on page 207 Packing the JCS 1200 Platform for Shipment on page 208 Guidelines for Packing JCS 1200 Platform Components for Shipment on page 209 Locating the JCS 1200 Alarm Panel Serial Number The alarm panel module serial number is located on the side of the alarm panel module (see Figure 89 on page 197).
Page 230: Tools And Parts Required To Remove Components From The Jcs 1200 Platform
Juniper Control System (JCS) 1200 Platform Hardware Guide Part no.: 740-023160 Component serial no.: JCS-TAP-SN-BCG001 CLEI: Not Available Replacing a JCS 1200 Alarm Panel Module or Module Filler on page 96 Related Topics Contacting Customer Support on page 206 JCS 1200 Return Procedure on page 207...
Page 231: Figure 91: Jcs 1200 Management Module Serial Number Label
Tools and Parts Required to Remove Components from the JCS 1200 Platform on page 208 Guidelines for Packing JCS 1200 Platform Components for Shipment on page 209 Locating the JCS 1200 Management Module Serial Number The product name, serial number, and media access control (MAC) address are located on the identification label on the side of the management module (see Figure 91 on page 199).
Page 232: Figure 92: Jcs 1200 Media Tray Serial Number Label
CNETCMUS.PKT Rel date: 02-11-08 Rev: Replacing a JCS 1200 Management Module or Module Filler on page 124 Related Topics Contacting Customer Support on page 206 JCS 1200 Return Procedure on page 207 Tools and Parts Required to Remove Components from the JCS 1200...
Page 233 Tools and Parts Required to Remove Components from the JCS 1200 Platform on page 208 Guidelines for Packing JCS 1200 Platform Components for Shipment on page 209 Locating the JCS 1200 Midplane Serial Number The midplane serial number is not visible on the chassis. To view the serial number label, you must remove the components that attach to the midplane (see “Removing...
Page 234: Figure 93: Jcs 1200 Power Module Serial Number Label
Tools and Parts Required to Remove Components from the JCS 1200 Platform on page 208 Guidelines for Packing JCS 1200 Platform Components for Shipment on page 209 Locating the JCS 1200 Power Module Serial Number The power module serial number is located on the top of the power module (see Figure 93 on page 202).
Page 235: Figure 94: Jcs 1200 Routing Engine Serial Number Label
Tools and Parts Required to Remove Components from the JCS 1200 Platform on page 208 Guidelines for Packing JCS 1200 Platform Components for Shipment on page 209 Locating the JCS 1200 Routing Engine Serial Number The Routing Engine model number and serial number are located on the ID label...
Page 236: Figure 95: User Label Locations On The Jcs 1200 Platform
A set of blank labels comes with each Routing Engine (see Figure 95 on page 204). Record identifying information on a label, and place it on the JCS 1200 platform top bezel, just above the Routing Engine. Do not place the label on the Routing Engine itself or in any way block the ventilation holes on the Routing Engine.
Page 237: Packing The Jcs 1200 Platform For Shipment
JCS 1200 Return Procedure on page 207 Packing the JCS 1200 Platform for Shipment on page 208 Guidelines for Packing JCS 1200 Platform Components for Shipment on page 209 Locating the JCS 1200 Switch Module Serial Number The switch module serial number is located on the side of the switch module (see Figure 96 on page 205).
Page 238 Rev: 0104 MAC Address: 00:18:B1:1B:89:00 Replacing a JCS 1200 Switch Module or Module Filler on page 143 Related Topics Contacting Customer Support on page 206 JCS 1200 Return Procedure on page 207 Tools and Parts Required to Remove Components from the JCS 1200...
Page 239 NOTE: Do not return any component to Juniper Networks, Inc. unless you have first obtained an RMA number. Juniper Networks, Inc. reserves the right to refuse shipments that do not have an RMA.
Page 240 Attach an electrostatic discharge (ESD) grounding strap to your bare wrist and connect the strap to one of the ESD points on the chassis. Shut down power to the JCS 1200 platform by pressing the power switch for all power supplies to the off ( ) position.
Page 241: Guidelines For Packing Jcs 1200 Platform Components For Shipment
The three lifters can then move the platform to the shipping crate. Place the JCS 1200 platform in the shipping crate or onto the pallet. If on a pallet, bolt the JCS 1200 platform to the pallet.
Page 242 Contacting Customer Support on page 206 Related Topics JCS 1200 Return Procedure on page 207 Tools and Parts Required to Remove Components from the JCS 1200 Platform on page 208 Packing the JCS 1200 Platform for Shipment on page 208...
Page 243: Appendix E Cable Connector Pinouts
Cable Connector Pinouts This appendix describes the pinouts for the following cable connectors: Serial Cable Characteristics for the JCS 1200 Management Module on page 211 Pinouts for the RJ-45 Adapters on page 212 Pinouts for the JCS 1200 Alarm Panel Interface Connector on page 213 Serial Cable Characteristics for the JCS 1200 Management Module Pinouts for the management module serial cable are shown in Table 34 on page 211.
Page 244: Table 35: Pinouts For The Amm Adapter
RJ-45 Male 2 (DCD) To connect a console to the JCS 1200 Routing Engines, you can connect a breakout serial cable to the external serial port on the alarm panel module. If needed, you can use the RJ-45 CPU adapters to connect each of the 12 RJ-45 connectors to the console.
Page 245: Pinouts For The Jcs 1200 Alarm Panel Interface Connector
Output Major alarm common Output Reserved Reserved Reserved Reserved JCS 1200 Alarm Panel Module Description on page 12 Related Topics JCS 1200 Alarm Panel Module Connectors and LEDs on page 12 Pinouts for the JCS 1200 Alarm Panel Interface Connector...
Page 246 Juniper Control System (JCS) 1200 Platform Hardware Guide Pinouts for the JCS 1200 Alarm Panel Interface Connector...
Page 247: Index
Part 5 Index Index on page 217 Index...
Page 248 Juniper Control System (JCS) 1200 Platform Hardware Guide Index...
Page 249 Index Symbols #, comments in configuration statements....xxiii battery ( ), in syntax descriptions..........xxiii environmental compliance.........183 < >, in syntax descriptions........xxiii lithium..............183 [ ], in configuration statements.........xxiii bezel { }, in configuration statements........xxiii installing...............98 | (pipe), in syntax descriptions........xxiii removing..............97 replacing...............97 bezel collar installing.............102 AC power...
Page 250 Juniper Control System (JCS) 1200 Platform Hardware Guide removing............113 replacing.............113 DC power serial number, locating........196 connecting............63 checklist consumption............192 installation............94 disconnecting............65 site preparation.............33 electrical specifications........192 Class A electronic emission notice......183 provisioning............192 clearance, around rack..........38 DC terminal cover comments, in configuration statements....xxiii installing.............115...
Page 251 LED..............15 preparing to install..........39 installing.............118 requirements............94 LED...............14 unpacking the JCS 1200 platform......40 overview...............14 instructions problems..............86 packing removing............116 platform for shipment.........208 replacing.............116 returning platform..........207 serial number, locating........198 interference troubleshooting.............86...
Page 252 Juniper Control System (JCS) 1200 Platform Hardware Guide Ethernet activity (on management module)..18 Ethernet link OK (on switch module)....29 machine type, locating..........196 Ethernet Tx/Rx............29 maintenance guidelines Ethernet-link status (on management warnings.............164 module).............18 major system fault LED fan module............14 alarm panel module..........13 fan module error...........15...
Page 253 Index module platform alarm panel See alarm panel module description..............3 fan See fan module power management See management module AC, connecting............62 media tray See media tray connectors............30 MUX card See MUX card DC, connecting.............63 power See power module disconnecting............65 switch See switch module problems..............89 modules requirements and specifications......189...
Page 254 Juniper Control System (JCS) 1200 Platform Hardware Guide RFI................189 fire safety............155 Routing Engine rack connecting to console...........72 connection to building structure....37 control panel............25 size and strength...........36 description............24 thermal output............187 installing.............141 specifications and features..........7 LEDs..............26 standards compliance..........181 overview...............24 starting the Routing Engine..........73 pinouts for cable connections......211...
Page 255 U (rack unit)..............36 United States electronic emission Class A notice..183 United States FCC Class A notice........183 unpacking the JCS 1200 platform.........40 USB device, problems..........88 warnings electrical.............169 general..............151 installation............155 laser and LED.............160 levels defined............149 maintenance and operational......164...
Page 256 Juniper Control System (JCS) 1200 Platform Hardware Guide Index...

Juniper JCS 1200 Hardware Manual

Chapter 1 JCS 1200 Platform Overview

Chapter 2 Hardware Component Overview

Chapter 3 Preparing the Site for JCS 1200 Platform Installation

Chapter 4 Unpacking the JCS 1200 Platform

Chapter 5 Installing the JCS 1200 Mounting Hardware

Chapter 6 Installing the JCS 1200 Platform

Chapter 7 Connecting the JCS 1200 Platform

Chapter 8 Configuration Guidelines

Chapter 9 Troubleshooting Common JCS 1200 Platform Problems

Chapter 10 Replacing Components in a JCS 1200 Platform

Appendix A Safety and Regulatory Compliance Information

Quick Links

Troubleshooting

Related Manuals for Juniper JCS 1200

Summary of Contents for Juniper JCS 1200