Lippert Components Power Gear SlimRack Slide-out Installation And Service Manual
  1. Manuals
  2. Brands
  3. Lippert Components Manuals
  4. Motorhomes
  5. Power Gear SlimRack Slide-out
  6. Installation and service manual

Lippert Components Power Gear SlimRack Slide-out Installation And Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Slim Rack Slide-out
INSTALLATION AND
SERVICE MANUAL
© Copyright LCI/Power Gear Issued: October 2015 #3010002813, Rev. OG
Controls: 1510000236 and 1510000276
Page 1
Rev: 05.24.2016
3010002813 Slim Rack Slide-out Programming Installation and Service Manual

Advertisement

Table of Contents
loading

Related Manuals for Lippert Components Power Gear SlimRack Slide-out

Summary of Contents for Lippert Components Power Gear SlimRack Slide-out

  • Page 1 Slim Rack Slide-out INSTALLATION AND SERVICE MANUAL © Copyright LCI/Power Gear Issued: October 2015 #3010002813, Rev. OG Controls: 1510000236 and 1510000276 Page 1 Rev: 05.24.2016 3010002813 Slim Rack Slide-out Programming Installation and Service Manual...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS System Information Component Descriptions Installation General Requirements Mechanical Components Electrical Components Programming Setting the Retracted Stop Point Setting the Extended Stop Point Installation Issues Operation Prior To Moving the Slide-Out Room: Extending the Room Retracting the Room Preventative Maintenance Troubleshooting Override Mode...

  • Page 3: Installation

    Installation General Requirements • Power and wiring MUST be such that there is not less than 10.5 running volts supplied at the motor leads under maximum load. • Slide system controls MUST come from Power Gear. Controls supplied by other companies will void warranty.

  • Page 4: Electrical Components

    Lift the slide room box into the coach opening and push in until the mounting flange meets the exterior wall. Verify the weight of the room is supported by the floor rollers and not the slide-out mechanism (Fig. 2). NOTE: If the room is not completely supported by the floor rollers, you will hear a slight “popping” sound as the room settles on to the rollers.
  • Page 5 B. 1510000276 control. With the switch in the left position (as shown) the control will be in bypass (not looking for a park brake input signal). With the switch in the right position the control will be looking for a park brake signal input. If using the park brake feature, route the park brake input harness from the park brake signal source to the control box.

  • Page 6: Programming

    Programming NOTE: When retracting or extending, the switch will need to be depressed and held for 2 seconds after the room stops moving. Failure to do so will cause the stops to NOT be set. Always make sure that the slide-out room path is clear of people and objects before and during operation of the slide-out room.

  • Page 7: Operation

    Operation Always make sure that the slide-out room path is clear of people and objects before and during operation of the slide-out room. Always keep away from the slide rails when the room is being operated. The gear assembly may pinch or catch on loose clothing causing personal injury.

  • Page 8: Troubleshooting

    Troubleshooting This control has the ability to detect and display several faults. When a fault is detected, the room movement may stop and 2 different LEDs on the control box will flash in a pattern. • The Fault Code LED (Fig. 9) on the rocker switch will flash RED a number of times corresponding to the number of red flashes on the control box (Fig.

  • Page 9: Override Mode

    Override Mode In the event of component failure or loss of system power, your slide-out can be manually overridden and retracted for travel. NOTE: At any time during the override procedure, the unit will exit this mode if the room has not been moved for five (5) minutes.

  • Page 10: Alternate Overrides

    Alternate Overrides It may be possible to manually retract the room by accessing the ½” square drive tube at the bottom of each vertical channel assembly. This will only be possible if there is access to this area. Using a ½” 8-point star socket (Fig. 13) and alternating from one side to the other, turn the ½” square drive tube to bring the room in.
  • Page 11 Fig. 17 - Wiring Information for Control Box 151000276 Page 11 Rev: 05.24.2016 Slim Rack Slide-out Manual...
  • Page 12 Fig. 18 - Wiring Information for Control Box 151000236 Page 12 Rev: 05.24.2016 Slim Rack Slide-out Manual...

  • Page 13: Notes

    Notes __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________ __________________________________________________________________________________________...
  • Page 14 The contents of this manual are proprietary and copyright protected by Lippert Components, Inc. (“LCI”).  LCI prohibits the copying or dissemination of portions of this manual unless prior written consent from an authorized LCI representative has been provided.  Any unauthorized use shall void any applicable warranty. ...

Table of Contents