Maytag MFI2269FRZ02 User Instructions page 10

Adjusting Controls
The REFRIGERATOR control adjusts the refrigerator compartment
temperature. The FREEZER control adjusts the freezer
compartment temperature.
If you need to adjust the temperature in either the refrigerator or
freezer compartment, use the settings listed in the chart as a
guide.
To Adjust Set Point Temperatures:
The first touch of the up or down arrow touch pad displays the
current temperature set point.
Press the up or down arrow touch pads until the desired
temperature set point is displayed.
NOTE: Except when first turning on the refrigerator, do not
adjust either temperature control more than one setting at a
time. Wait 24 hours between adjustments for the temperature
to stabilize.
CONDITION/REASON:
REFRIGERATOR too warm
FREEZER too warm/too little
ice
REFRIGERATOR too cold
FREEZER too cold
Cooling On/Off
IMPORTANT:
Depending on your model you may have a control center with
an On/Off button (Style 1), or you may have a control center
without an On/Off button (Style 2).
The On/Off control turns off cooling for both compartments
and turns off the dispenser. It does not disconnect power to
the refrigerator.
Style 1 – Press and hold the On/Off button for 3 seconds. The red
LED will light up to indicate that cooling is Off. Press On/Off again
to turn cooling back on. The LED will turn off.
Style 2 – Press the Freezer up arrow touch pad until OFF appears
in the display. Neither compartment will cool. Press the Freezer or
Refrigerator down arrow touch pad to turn cooling back on.
Additional Control Center Features
PowerCold™ Feature
The PowerCold™ feature assists with periods of high refrigerator
use, full grocery loads, or temporarily warm room temperatures.
Press the POWERCOLD touch pad to set the freezer and
refrigerator to the lowest temperature settings. Press the
POWERCOLD touch pad again to return to the normal
refrigerator set point.
10
ADJUSTMENT:
REFRIGERATOR Control
1° lower
FREEZER Control 1° lower
REFRIGERATOR Control
1° higher
FREEZER Control 1° higher
NOTE: The PowerCold™ feature will automatically shut off in
approximately 2 hours. When PowerCold™ is on, the
temperature cannot be adjusted.
Humidity Control (on some models)
The Humidity Control feature turns on a heater to help reduce
moisture on the door hinge seal. Use in humid environments or
when you notice moisture on the door hinge seal. The refrigerator
uses more energy when Humidity Control is on.
Press HUMIDITY CONTROL to turn on the door heater. Press
Humidity Control again to turn off the heater. The LED will be
illuminated when Humidity Control is on.
Temp Alarm
The Temp Alarm feature provides temperature information in the
event of a power outage.
Power outage: During a power outage, if the temperatures in the
refrigerator and freezer compartments exceed normal operating
temperatures, the highest temperature reached will be displayed.
Press the TEMP ALARM touch pad until the indicator light is
lit, to turn on this feature. Press and hold Temp Alarm for
3 seconds until the indicator light goes off to turn off this
feature.
Temperature alarm: An alarm will sound repeatedly if the freezer
or refrigerator compartment temperatures exceed normal
operating temperatures for an hour or more.
The temperature displays will alternately show the current
temperatures and the highest temperatures the compartments
reached.
Press the TEMP ALARM touch pad once to stop the audible
alarm and alternating temperature displays. The Temp Alarm
light will continue to flash until the refrigerator returns to the
set temperature.
Door Alarm
The Door Alarm feature sounds a chime every few seconds when
the refrigerator door has been left open for 5 continuous minutes.
The chime will sound until the door is closed or Door Alarm is
turned off.
Press the DOOR ALARM touch pad to turn this feature on or
off. The indicator light will be lit when the Door Alarm feature
is on.
Filter Reset
See "Water Filtration System."