Marvel ML24BN Series Installation, Operation And Maintenance Instructions
Hide thumbs
Also See for ML24BN Series:
Related Manuals for Marvel ML24BN Series
Summary of Contents for Marvel ML24BN Series
- Page 1 EN Installation, Operation and maintenance Instructions FR Instructions d’installation, d’utilisation et d’entretien Beverage Dispensers Distributeurs de boissons ML24BN MO24BN...
-
Page 2: Table Of Contents
CONTENTS Important Safety Instructions Contents: Warnings and safety instructions appearing in this guide Safety information ...............2 are not meant to cover all possible conditions and situa- Unpacking your appliance ..........3 tions that may occur. Common sense, caution, and care Warranty registration .............3 must be exercised when installing, maintaining, or operat- Installing your appliance ............4 ing this appliance. -
Page 3: Unpacking Your Appliance
Keep your carton and packaging until your appliance has been thoroughly inspected and found to be in good condi- tion. If there is damage, the packaging will be needed as proof of damage in transit. Afterwards please dispose of all items responsibly. MARVEL WARNING XXXXXXXXXXXX WARNING - XXXXXXXXXXXX Dispose of the plastic bags which can be a suffocation hazard. -
Page 4: Installing Your Appliance
The over- all height of your Marvel appliance may be adjusted higher (by turning the leveling leg out, CCW) and lower (by turning the leveling leg in, CW) dimensions as shown in Table "A". -
Page 5: Electrical Connection
INSTALLING YOUR APPLIANCE WARNING Electrical Shock Hazard Do not remove • Do not use an extension cord with this appliance. ground prong They can be hazardous and can degrade product performance. • This appliance should not, under any circumstanc- es, be installed to an un-grounded electrical supply. •... -
Page 6: Product Dimensions Single And Double Tap
PRODUCT DIMENSIONS - SINGLE AND DOUBLE TAP MODELS ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J" 24" **34" to 35" 24" ⁄ " ⁄ " to 34 ⁄ " ⁄ " ⁄ " ⁄... -
Page 7: Product Dimensions Mobile
PRODUCT DIMENSIONS - MOBILE MODELS ⁄ " Single dispense tower shown (54.6 cm) ⁄ " (66.7 cm) ⁄ " ⁄ " (30.3 cm) (117.9 cm) 11" ⁄ " (27.9 cm) (31.1 cm) ⁄ " (93.5 cm) ⁄ " (15.9 cm) ⁄... -
Page 8: Using Your Electronic Control - Indoor Models
USING YOUR ELECTRONIC CONTROL - INDOOR MODELS Temp Temp Minus On/Off Plus Lock System Status keypad keypad keypad Display Area keypad indicators Figure 11 Electronic single zone control To wake the display press any keypad. A confirm tone will sound, and the current storage compartment temperature will be displayed. -
Page 9: Adjusting The Temperature
USING YOUR ELECTRONIC CONTROL - INDOOR MODELS Factors that affect the storage compartment stabilized temperature: • Changes to temperature setting. • Room temperature changes. • Temperature of stored contents. - Loading warm contents. Adjusting the temperature: - Cold content load will delay the change to a warmer To set or check the set-point temperature (with the control set-point temperature. -
Page 10: Control Lock
USING YOUR ELECTRONIC CONTROL - INDOOR MODELS Power Failure ALARM RESET • Power failure - If power to the appliance is inter- Control lock: rupted the System Status indicator will turn-off and the "Power Failure" indicator will flash. Additionally, an The control panel can be locked to avoid unintentional "ALARM RESET"... -
Page 11: Vacation Mode
USING YOUR ELECTRONIC CONTROL - INDOOR MODELS This alarm condition can be reset by momentarily pressing the "On/Off" keypad. If this alarm occurs it is recommended that you check the condition of your stored contents, even though the appliance is operating normally and the temperature has recovered, as pro- longed temperature excursions could spoil perishables. -
Page 12: Using Your Electronic Control - Outdoor Models
"Alarm" will be "OFF" will appear on the display. illuminated. Please call Marvel Customer Service or your dealer if this error code is displayed. If the beer dispenser is not on, "OFF" will be shown on the display. -
Page 13: Overlay Door Panel Installation
OVERLAY DOOR PANEL INSTALLATION If you purchased an overlay panel model, your unit is WARNING equipped with articulated hinges to allow fully integrated built-in installations. Custom panel thicknesses of ⁄ " (15 mm) and ⁄ " (18 mm) are accommodated. Use extreme caution with the articulated hinges. - Page 14 OVERLAY DOOR PANEL INSTALLATION Step 2: Remove the door gasket With the door laying on a flat surface and starting at a corner of the door, remove the magnetic door gasket from the interior side of the door, see Figure 16. Set the gasket aside on a flat surface.
- Page 15 OVERLAY DOOR PANEL INSTALLATION Clearance for hinge Clearance at top and bottom Clearance for for hinge screw head, at top and Clearance for 4 places bottom screw head, 4 places Figure 17 Left Hand Hinged Door 24" (61 cm) wide appliance Figure 19 Right Hand Hinged Door 24"...
- Page 16 OVERLAY DOOR PANEL INSTALLATION CAUTION Step 5: Install the door Carefully open the top and bottom hinges on the door being careful as there are many pinch points. Place the hinges Weight of overlay door panel must not over the 4 screws in the cabinet, 2 at the top and 2 at the exceed 15 pounds (6.8 kg) for a solid bottom and slide the door into position.
-
Page 17: Using Your Beverage Dispenser
USING YOUR BEVERAGE DISPENSER Shelving If you are using a quarter barrel of beer, you can add shelf space for keeping your mugs chilled. The quarter barrel The unit is shipped with the (2) shelves taped in place in must set on the floor, it cannot fit on the shelf, see the upper and the lower shelf positions. -
Page 18: Tap Equipment And Assembly
USING YOUR BEVERAGE DISPENSER Tools required for installation: This beer dispensing unit will support one half ( ⁄ ) barrel or one quarter ( ⁄ ) barrel. The double draft tower units can Flat bladed screwdriver support two sixth ( ⁄... - Page 19 USING YOUR BEVERAGE DISPENSER Single Dispense Tower Kit Double Dispense Tower Kit Connect ,etc..Connect ,etc..Figure 33 Figure 32 Figure 27 Double Single Dispense Hose clamps Dispense Tower use for connections Tower Hose clamps use for connections Figure 28 Coupler Figure 34 Figure 29...
- Page 20 USING YOUR BEVERAGE DISPENSER Rear of counter top 4. If you are installing your keg refrigerator under a coun- ter you will need to drill 5 holes in the counter top to ⁄ " mount the tower. The first hole is a 1 ⁄...
- Page 21 USING YOUR BEVERAGE DISPENSER 9. Hooking up the keg coupler to the keg: Verify the cou- pler is in the "OFF" position (see Figure 42a).Align the lugs on the keg with the corresponding openings on the Connect keg coupler and turn clockwise until the coupler stops with "S"...
-
Page 22: Externally Mounting Gas Tank
USING YOUR BEVERAGE DISPENSER Optional gas tank external mounting bracket: CAUTION The optional mounting bracket is designed to hold the 5# gas cylinder that comes with the beer dispenser. Larger cylinders may be purchased from a third party and mounted If the gas tank is placed on the floor it must be secured in externally. -
Page 23: Gas Regulator
USING YOUR BEVERAGE DISPENSER Gas Regulator (Single Dispense Tower) Gas Regulator (Double Dispense Tower) Your beer dispenser comes equipped with a 5 pound gas Your beer dispenser comes equipped with a 5 pound gas tank and a single gauge regulator. The gauge reads the tank and a dual gauge regulator. -
Page 24: Drain Kit
Cleaning the drain sump: On a free standing beverage dispenser remove the Marvel grate from in front of the tower, clean with soap and water and dry before reinstalling. Clean the sump area with soapy water and dry. (See figure 48). -
Page 25: Tap Cleaning Kit
CARE AND CLEANING Cleaning and Maintaining Dispensing System Faucet Cleaning The dispensing system needs to be cleaned between Turn off the gas supply with the shutoff valve(s) under the usage to prevent spoilage and/or foul taste in your beer. regulator (see Figure 46 or Figure 47) and open the fau- cet to relieve the pressure. -
Page 26: Front Grille
CARE AND CLEANING Tap Cleaning Kit Front Grille This is an optional item (part number 42242373) Kit in- Be sure that nothing obstructs the required air flow open- cludes everything to quickly clean tap. Includes cleaning ings in front of the cabinet. At least once or twice a year, solution, pump, mixing bottle, brush and wrench. - Page 27 CARE AND CLEANING Long term storage / winterization: 1. Time to Winterize, when the daily low ambient tempera- ture is at or below 38F. CAUTION Operating of the unit at ambient temperatures below the recommended Winterization temperature will void your war- ranty.
- Page 28 CARE AND CLEANING 1. Leave door open and allow to completely dry out be- fore closing door. 2. Thoroughly clean the door gasket with anti-bacterial cleaner to be followed with clean rinse water to remove any residual chemicals. 3. Thoroughly clean the exterior with a cleaner approved for stainless steel .
-
Page 29: Stainless Steel Maintenance & Energy Saving Tips
STAINLESS STEEL MAINTENANCE AND ENERGY SAVING TIPS Background NOTE Stainless steel does not stain, corrode, or rust as easily as ordinary steel, but it is not stain or corrosion proof. Stain- less steels can discolor or corrode if not maintained prop- Stainless steel products should never be installed, or stored erly. -
Page 30: Obtaining Service
OBTAINING SERVICE If Service is Required: • If the product is within the first year warranty period please contact your dealer or call Marvel Customer Service at 800.223.3900 for directions on how to obtain warranty coverage in your area. •... -
Page 31: Troubleshooting
TROUBLESHOOTING Before You Call for Service CAUTION If the appliance appears to be malfunctioning, read through this manual first. If the problem persists, check the trouble- shooting guide below. Locate the problem in the guide and In the unlikely event you lose cooling in your unit, do not refer to the cause and its remedy before calling for service. -
Page 32: Warranty
1-YEAR LIMITED PARTS AND LABOR WARRANTY For one year from the date of original purchase, this Marvel product warranty covers all parts and labor to repair or replace any part of the product that proves to be defective in materials or workmanship. For products installed and used for normal residential use, material cosmetic defects are included in this warranty, with coverage limited to 60 days from the date of original purchase.