Reading Out Information; Configuring Date, Time, Units Of Measurement, Contrast And Backlight; Configuring User Profile And Home Pages - Daikin Altherma EHY2KOMB28AA User Reference Manual

Usage example: You go away during the winter
If you are in the following situation:
▪ In 2 days, you go away for 2 weeks during the winter.
▪ You want to save energy, but prevent your house from freezing.
Then you can do the following:
Prerequisite: You switched the permission level to Advanced end
user.
1 Configure the holiday. Go to [2]:
the following settings:
Setting
Holiday mode
From
Until
Operation mode
Heating
2 Activate the holiday mode.
▪ Go to [2.1]: > Holiday > Holiday.
▪ Select Yes and press
Advantage:
▪ Before and after your holiday, your normal schedule will be used.
▪ During your holiday, you save energy and prevent your house
from freezing.
Usage example: You come home during your holiday
If you are in the following situation:
▪ You configured and activated the holiday mode (Away).
▪ During your holiday, you come home for a few hours and want to
use your normal schedule.
Then you can do the following:
1 Deactivate the holiday mode.
2 When you go away again, activate the holiday mode again.
Advantage:
You do NOT have to change your schedule or holiday configuration.
4.6.4

Reading out information

To read out information
Prerequisite: You switched the permission level to Advanced end
user.
1 Go to [6]: > Information.
Possible read-out information
In menu...
[6.1] Sensor information
[6.2] Energy metering
[6.3] Error handling
[6.4] User permission level
[6.5] Actuators
[6.6] Operation modes
[6.7] Running hours
EJHA04AAV3 + EHY2KOMB28+32AA
Daikin Altherma hybrid monobloc
4P531181-1 – 2018.06
> Holiday, and configure
Value
Away
2 February 2014
16 February 2014
Heating
12°C
.
You can read out...
Room, tank or DHW, outside,
and leaving water temperature.
(If applicable)
Consumed electricity, and
consumed gas.
Error history and contact/
helpdesk number.
Current user permission level.
Status/mode of each actuator.
Example: Domestic hot water
pump ON/OFF.
Current operation mode.
Example: Defrost/oil return
mode.
Running hours of the system.
In menu...
[6.8] Version
4.6.5 Configuring date, time, units of
measurement, contrast and backlight
To configure time and date
Prerequisite: You switched the permission level to Advanced end
user.
1 Go to [1]: > Set time/date.
INFORMATION
Switch to Adv. end user to change daylight saving time and
12/24h notation.
To configure units of measurement
Prerequisite: You switched the permission level to Advanced end
user.
1 Go to [7.6]: > User settings > Unit of measurement.
Possible units of measurement settings
Setting
Decimal point
Temperature
Consumed gas
To configure the contrast of the user interface
Prerequisite: You switched the permission level to Advanced end
user.
1 Go to [7.1.1]: > User settings > Display > Contrast.
To configure the backlit LCD time of the user interface
Prerequisite: You switched the permission level to Advanced end
user.
1 Go to [7.1.2]: > User settings > Display > Backlit LCD time.
4.6.6

Configuring user profile and home pages

To set a user profile
Prerequisite: You switched the permission level to Advanced end
user.
1 Go to [7.1.3]: > User settings > Display > User profile.
2 Select a user profile and press
Possible user profiles
If user profile = Detailed, you can see and do more on the home
pages.
User profile = Basic
Mon 15:20
Room
20.0°C
Actual temperature
4 Operation
You can read out...
Version information about the
system.
Possible units of measurement
▪ Dot
▪ Comma
▪ °C
▪ °F
▪ m³
▪ ft³
▪ kWh
For correct operation, only use
kWh. Do NOT use m³ or ft³.
.
User profile = Detailed
Mon 15:20
20.0°C
Room
Actual temperature
Scheduled
Tue 17:30
User reference guide
15