Advertisement
4. Push the top of the module down into the appropriate module spaces in the
FT2-ELEC assembly so that the module slides into place. Use the guide ribs on the
front and rear of each module to help position the module in the assembly.
Installing the FT2A-CHGR-USBA/C into the FT2-ELEC Assembly - Overhead View
FT2A-CHGR-USBA/C
5. Once all modules and plates are installed and level with their surroundings, place the
removed locking bars back into position so that the screws on either side engage
the screw holes in the assembly. Then, hand tighten the two screws attached to the
sides of each bar until the bars are secured to the assembly.
CAUTION: To avoid stripping the screws on the locking bars, hand tighten the
screws using a manual screwdriver only.
As of the date of manufacture, the product has been tested and found to comply with speci cations
for CE marking.
This product is Listed to applicable UL
®
Standards and requirements tested by Underwriters
Laboratories Inc.
Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters
Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CAUTION: Changes or modi cations not expressly approved by the manufacturer responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
6. Hold the magnetic bezel over the assembly so that the lid retraction button on the
bezel is aligned with the front of the assembly. Then, lower the bezel onto the
assembly so that the lowered retractable lid ts inside the rear opening in the bezel
and the magnets snap into place against the assembly. Refer to the illustration
below.
FT2 with FT2A-CHGR-USBA/C and Bezel Installed
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3 (B)/NMB-3(B)
The product warranty can be found at www.crestron.com/warranty.
The speci c patents that cover Crestron products are listed at www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For speci c information, please visit
www.crestron.com/opensource.
Crestron, the Crestron logo, and FlipTop are either trademarks or registered trademarks of Crestron
Electronics, Inc. in the United States and/or other countries. UL and the UL logo are either trademarks
or registered trademarks of Underwriters Laboratories, Inc. in the United States and/or other
countries. USB-C and USB Type-C are either trademarks or registered trademarks of the USB
Implementers Forum in the United States and/or other countries. Other trademarks, registered
trademarks, and trade names may be used in this document to refer to either the entities claiming the
marks and names or their products. Crestron disclaims any proprietary interest in the marks and
names of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2017 Crestron Electronics, Inc.
Crestron Electronics, Inc.
15 Volvo Drive, Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Retractable lid
ts inside this
opening in bezel
Retractable lid
Lid retraction
button
Installation Guide - DOC. 8219A
(2049456)
12.17
Speci cations subject to
change without notice.
Advertisement
