Table of Contents Preface ������������������������������������������������������������������������������������������������� i Safety Instructions ������������������������������������������������������������������������������ ii About This Manual ������������������������������������������������������������������������������ iv Chapter 1� Product Features �������������������������������������������������������������� 1 1.1 Components ..................... 1 1.2 Specifications ..................2 1.3 Feature ..................... 2 Chapter 2� Hardware Setup ���������������������������������������������������������������� 5 2.1 Top Cover ....................5 2.2 Power Supply Unit Module ..............
Page 3
Document Release History Release Date Version Update Content October User's Manual release to public. 2018 June QIG update 2019 Content...
Disclaimer AIC shall not be liable for technical or editorial errors or omissions contained herein. The information provided is provided "as is" without warranty of any kind. To the extent permitted by law, neither AIC or its affiliates, subcontractors or suppliers will be liable for incidental, special or consequential damages including downtime cost;...
Safety Instructions Before getting started, please read the following important cautions: • All cautions and warnings on the equipment or in the manuals should be noted. • Most electronic components are sensitive to electrical static discharge. Therefore, be sure to ground yourself at all times when installing the internal components. •...
Page 7
• If one of the following situations arise, the equipment should be checked by service personnel: 1. The power cord or plug is damaged. 2. Liquid has penetrated the equipment. 3. The equipment has been exposed to moisture. 4. The equipment does not work well or will not work according to its user manual. 5.
LED descriptions. Chapter 4 Technical Support For more information or suggestion, please contact the nearest AIC corporation representative in your district or visit the AIC website: http://www.aicipc.com/en. It is our greatest honor to provide the best service for our customers.
Chapter 1� Product Features RSC-1AT User Manual Chapter 1. Product Features RSC-1AT User Manual Chapter 1. Product Features RSC-1 AT is a flexible rackmount storage chassis with tool-less design. This product supports hot swapple HDDs and easy swap fans. For more information about our product, please visit our website at http://www.aicipc.com/en.
RSC-1AT User Manual Chapter 1. Product Features 1.2 Specifications Drive Bays External 2.5” hot swap mm : 438 x 680 x 43.5 Dimensions (W x D x H) 2 x 4-port 12Gb with SFF-8643 connector support 12G inches : 17 x 26.8 x 1.72...
Page 11
RSC-1AT User Manual Chapter 1. Product Features Front Panel 2.5" x 10 HDD tray System Switches and LED indicators in front panel Power On/Off System Reset Power System LED System HDD Activity LED LAN 1 LED LAN 2 LED Rear Panel...
Page 12
RSC-1AT User Manual Chapter 1. Product Features Top View 500W single power supply unit (650W 1+1 redundant power supply unit) 1x 4028 hotswap fans+ 4 x4056 PWM fans NOTE Motherboard is not included in this product.
Chapter 2� Hardware Setup RSC-1AT User Manual Chapter 2. Hardware Setup 2�1 Top Cover Push the release button on both sides of the top cover and push it toward the rear panel. Lift the top cover to complete removal.
Chapter 2. Hardware Setup RSC-1AT User Manual 2�2 Power Supply Unit Module Extract the power supply unit by pushing the ejector while pulling the power supply unit. Pull the module completely out of the chassis. Install the new power supply unit by pushing it into the chassis. Ensure that the module is accurately inserted and locked into the chassis.
RSC-1AT User Manual Chapter 2. Hardware Setup 2�4 Hard Disk Drive Press the release button on the tray lever to loosen the lever. Pull the tray lever outward completely. Pull the tray out of the chassis. Match the dimples on the tray to insert the HDD into the tray.
Chapter 2. Hardware Setup RSC-1AT User Manual 2�5 HDD Backplane Module Detach the cables and hard disk drives from the backplane module. Release the module by shifting the hook. Dislodge the screws on the module. Lift the module upward to remove.
RSC-1AT User Manual Chapter 2. Hardware Setup 2�7 Slide Rail NOTE This sections provides a basic instruction for mounting the slide rail onto the system. Tool-less rails vary per order. The rail in this manaul may not exactly match the rail for your system.
Page 18
Chapter 2. Hardware Setup RSC-1AT User Manual Optional: Remove Metal Spacer for Aluminium Racks Metal Spacer 3. Aligning the Front Bracket with the Mounting Hole. 4. Push in to assembly the Front Bracket onto the Rack.
Page 19
RSC-1AT User Manual Chapter 2. Hardware Setup 5. Now the bracket is fixed onto the Rack. (Optional M6x10L screws are to secure the rails with posts if needed.) 6. Refer to step 3 and 4 to assemble the End Bracket onto the Rack.
Page 20
Chapter 2. Hardware Setup RSC-1AT User Manual 7. Assemble the inner channel onto the chassis using thescrews provided. 8. Push the chassis with inner channels into Slide to complete Rack Installation.
RSC-1AT User Manual Chapter 3. Hardware Specification 3�2�2 Connector and Jumper JACT_LED: External HDD Activity LED Input (Active low) JFAIL_LED: External HDD Fail LED Input (Active low) CN6 & CN7: Power Connector JCPLD_SEL: SGPIO Function and Setting Status Description Open Disable External Access LED input (JP11).
Chapter 4� Technical Support Taiwain, Global Headquarters South California, United States Address: No� 152, Section 4, Address: 21808 Garcia Lane Linghang N� Rd, Dayuan District, City of Industry, CA 91789, Taoyuan City 337, Taiwan United States Tel: +886-3-433-9188 Toll free: +7-4997019998 Fax: +886-3-287-1818 Tel: +1-909-895-8989 Fax: +1-909-895-8989#157...
Need help?
Do you have a question about the RSC-1AT and is the answer not in the manual?
Questions and answers