Renu Electronics WP Web HMI Series User Manual

Renu Electronics WP Web HMI Series User Manual

Advertisement

User Manual
®
WP Web HMI Series

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WP Web HMI Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Renu Electronics WP Web HMI Series

  • Page 1 User Manual ® WP Web HMI Series...
  • Page 2: Table Of Contents

    ................................11 DEFAULT PRODUCT SETTINGS..........................11 ......................11 NVIRONMENTAL PECIFICATIONS AND PPROVALS POWERING UP THE WP WEB HMI SERIES ........................ 12 GETTING STARTED WITH THE WEB HMI ........................12 ................................. 12 ETTINGS ............................12 NTERING INTO DEVICE SETTINGS ............................. 13...
  • Page 3: Introduction

    Act. Before you start ▪ RENU Electronics Pvt. Ltd is not responsible or liable for any indirect or consequential damage resulting from the use of this product. ▪ The user should check and confirm the suitability of the product before using in any specific application.
  • Page 4: Safety Precautions

    This section of the manual provides information which is critical regarding safety and therefore the user is advised to go through the information in detail before installing the product. User may contact RENU Electronics’ technical support team at support@renuelectronics.com any specific question(s) related to safety.
  • Page 5: Product Overview

    ▪ Make sure that metal cutting chips do not enter any other component, already installed in the panel. Product Dimensions This section of the manual provides dimensional details of Web HMI series products. All the dimensions shown below are measured in mm. WP6043TN © RENU Electronics Pvt. Ltd. Page 5 of 22...
  • Page 6 WP6070TN WP6101TN © RENU Electronics Pvt. Ltd. Page 6 of 22...
  • Page 7: Minimum Clearances

    The optimum method for grounding electronic equipment is to ground it separately from other high-power systems and to ground more than one unit of electronic equipment with a single-point ground. Following marked terminal is provided with the unit for grounding: © RENU Electronics Pvt. Ltd. Page 7 of 22...
  • Page 8: Product Specifications

    Resolution: 800 x 480pixels Colors: 16M Brightness: 350cd/m Backlight life: 30,000Hrs. Size: 10.1” Color TFT, WSVGA Color Web Panel Analog Resistive Touch Screen Resolution: 1024 x 600pixels Colors: 16M Brightness: 350cd/m Backlight life: 50,000Hrs. © RENU Electronics Pvt. Ltd. Page 8 of 22...
  • Page 9: Cpu, Memory And Power Supply

    GPU 2D / GPU 3D support 24VDC (±15%) with isolation RTC: eMMC:4GB Built-in. RAM:1GB Power Rating Unit Voltage Current Wattage WP6043TN 24VDC 220mA 5.5W WP6070TN 24VDC 250mA WP6101TN 24VDC 350mA 8.5W © RENU Electronics Pvt. Ltd. Page 9 of 22...
  • Page 10: Communication Interfaces

    The Web HMI comes with a USB slave device port that is USB 2.0 compliant. This port is for future use. Connector used: Micro USB Type B Female Pin number Signal © RENU Electronics Pvt. Ltd. Page 10 of 22...
  • Page 11: Usb Host Port

    5 to 150Hz, 3g peak (X, Y, Z) EN 55011 :2009/A1 :2010 EN 61131-2 :2007 EN 61000-6-2 :2005/AC :2005 EN 61000-6-4 : 2007/A1 :2011 Protection IP66 rated for front panel mounting Yes (Class I Division 2) RoHS © RENU Electronics Pvt. Ltd. Page 11 of 22...
  • Page 12: Powering Up The Wp Web Hmi Series

    Powering up the WP Web HMI Series To use the Web HMI as a browser, follow these steps to connect the device to a web-server. 1. Connect an Ethernet cable to the device. 2. Power up the device using 24VDC power supply by connecting it to the device’s pluggable terminal block.
  • Page 13: Administrator Password

    IP, the user should click on the “Static” radio button and enter the IP Address, Subset Mask and the Default gateway manually by using the OSK. The OSK pops-up when the respective textboxes are clicked. © RENU Electronics Pvt. Ltd. Page 13 of 22...
  • Page 14 1. On the network settings screen, click on the right arrow at the bottom right corner to view the calibration settings. 2. Click on the Calibrate Device button after the screen opens up. © RENU Electronics Pvt. Ltd. Page 14 of 22...
  • Page 15 4. After entering into the calibration mode the following screens open up. Follow the directions given on the screen to calibrate the touch-screen by touching and releasing the crosshairs. stage stage stage stage stage © RENU Electronics Pvt. Ltd. Page 15 of 22...
  • Page 16 This option gives the user to select option of controlling the brightness of the Web HMI. 1. To open the Brightness control screen, click on the highlighted button from the Password setting screen as highlighted below. © RENU Electronics Pvt. Ltd. Page 16 of 22...
  • Page 17 ▪ The user can exit the settings screens by clicking on the Home button placed at the bottom center of the screen. ▪ The user can go to the previous screen by clicking on the Left Arrow placed at the bottom left corner of the screen. © RENU Electronics Pvt. Ltd. Page 17 of 22...
  • Page 18: Web Application

    To reach this screen, click on the third button from the top left. Under the device information, the user will find the ‘Factory Reset’ button. Clicking on this button will perform the following functions: © RENU Electronics Pvt. Ltd. Page 18 of 22...
  • Page 19: Copyrights

    2. Click on ‘Update Browser’ or ‘Update Firmware’ [Note: The Web HMI uses a Chromium based browser.] ATTENTION: Make of USB Flash drive ATTENTION ▪ This device has been tested to work with Strontium® make USB flash drive. © RENU Electronics Pvt. Ltd. Page 19 of 22...
  • Page 20: Entering Into The Browser

    On powering up the Web HMI shows the screen as shown below. Do not click on the ‘Configuration’ button and let the timer of 5 seconds time out. The browser will open up the URL that was selected in the Web Application settings and will open up as shown below © RENU Electronics Pvt. Ltd. Page 20 of 22...
  • Page 21: Revision History

    • RENU Electronics is not responsible for any damage to the Web HMI or any other device used in this process. This document is solely for the purpose of providing the user a general direction of configuring the Web HMI.
  • Page 22: Notes

    NOTES © RENU Electronics Pvt. Ltd. Page 22 of 22...

This manual is also suitable for:

Wp6043tnWp6070tnWp6101tn

Table of Contents