Advertisement
OPERATION
Before First Use
Carefully unpack your appliance and remove all accessories. Wash them in warm, soapy water then
rinse and dry with a dry towel. Carefully wipe the exterior of the base if necessary. WARNING: Do
not immerse the appliance base in water or any other liquids.
Using the Electric Slicer & Grater
Attach the Feed Chute to the Appliance Base. This is done by holding the Feed Chute at a 45
degree angle to the right, inserting it in to the socket on the Appliance Base, then rotating it
45 degrees back to the left so that it is locked in to place in the upright position.
Select a cone suitable for the slicing or grating task you require and fit it onto the star shaped
drive mechanism at the back of the Feed Chute. Rotate it slightly clockwise to hold it in place.
Cut the ingredients into pieces that will fit into the Feed Chute and place a suitable container
under the outlet.
Connect the appliance to a suitable 220 -240V ~ 50Hz power outlet socket
Press the ON/OFF button once or twice to ensure that the Cone has locked into place and
turns freely.
Make sure that the Pusher has been removed from the Feed Chute, and then insert the pre-
cut food through the top of the Feed Chute.
Press and hold down the ON/OFF button to activate the motor then slowly push the food down
with the pusher. Do not exert too much pressure on the pusher, as this could affect the
quality of the end result and could even cause damage to the appliance.
Turn off by releasing the ON/OFF button.
To remove the cone unlock the Feed Chute by rotating it 45 degrees to the right then lock it
back into place by rotating 45 degrees back to the left. The Cone can now be easily removed.
Remember to unplug the unit from the power outlet when it is not in use, changing parts or is
left unattended.
Always clean the product immediately after each use. Disassembly is reversal of assembly
instructions.
Important: This appliance is designed for short term operation only. Do not run continuously for
more than 2 minutes. After 2 minutes stop and rest for 1 minute to allow the appliance to cool.
Note: The first time this appliance is used there may be a small amount of smoke and odour. This
is normal and is due to the protective coating placed on the motor at manufacture to protect it
during shipping.
Tip: For best results use firm ingredients. If the ingredients are too soft the will clump together
and accumulate in and around the cone. If the ingredients are too hard the appliance and cones
may become damaged.
Cone Selection
The Fine Grating Cone can be used for grating parmesan cheese, nuts and spices
The Medium Grating Cone can be used for grating cheese, carrots, breadcrumbs
The Coarse Grating Cone can be used for grating cheese, carrots, courgettes, onion
The Thin Slicing Cone can be used for slicing beetroot, apples, celery
The Thick Slicing Cone can be used for slicing cucumbers, carrots, potatoes
MAINTENANCE
Regular maintenance of your appliance will keep it safe and in proper operational order.
Service
Do not attempt to service this appliance. If it is faulty in any way, please follow the instructions on
the enclosed warranty card.
Before cleaning
When not in use or before cleaning, always disconnect the appliance from the mains supply.
The accessories should be separated from the base of the appliance before cleaning.
DO NOT IMMERSE THE BASE OF THE APPLIANCE OR ITS SUPPLY CORD IN WATER.
Cleaning
CAUTION: Care is needed when handling the sharp cutting blades, especially during cleaning.
Always clean the product immediately after each use. Rinse off food any scraps then thoroughly
wash parts in warm, soapy water (a soft nylon brush may be helpful) then rinse and dry with a dry
towel. Do not use any abrasive cleaners or harsh solvents. The Feed Chute and Cones can be
washed in a dishwasher on the top rack. Clean the base by wiping it with a damp cloth.
Advertisement
