Table of Contents
Advertisement
Quick Links
OWNER'S /
OPERATOR'S
MANUAL
MODEL NO.'s
HPD-16 MFL
HPD-16 HFL
HPD-20 MFL
HPD-20 HFL
CAUTION
For Safe Operation
Read Rules And
Instructions Carefully
SINO LEEINGLES, PIDA AYUDA
A AIGUIEN QUE SI LO LEA
PARA QUE LE TRADUZCA LAS
MEDIDAS DE SEGURIDAD.
THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD
1. Select an area for assembly that is clean and free of any
debris which might cause persons working on the
assembly to trip.
2. Do not lift heavy parts or assemblies. Use crane, jack,
tackle, fork trucks or other mechanical devices.
3. Preview the assembly instructions in your operator's
manual before proceeding further.
4. If the assembly instructions call for parts or assemblies to
be blocked up, use only blocking material that is in good
condition and is capable of handling the weight of the
assembly to be blocked. Also insure that the blocking
material is on a clean, dry surface.
5. Never put hands, or any part of body, under blocked up
assemblies if at all possible.
FRONT LOADER MOUNTED
HYDRAULIC POST DRIVERS
Safety Instructions
Tractor Preparation
Operating Instructions
CAUTION
BEFORE ATTEMPTING TO BEGIN ASSEMBLING THIS MACHINE
Model HPD-20 MFL Shown
Assembly & Mounting
Maintenance
Repair Parts
6. After completing assembly, thoroughly inspect the
machine to be sure that all nuts, bolts, hydraulic fittings
or any other fastened assemblies have been thoroughly
tightened.
7. Before operating the machine, thoroughly read the
operation section of your operator's manual.
8. Before operating, read the maintenance section of your
operator's manual to be sure that any parts requiring
lubrication, such as gearboxes, are full, to avoid any
possible damage.
9. Before operating equipment – If you have any
questions regarding the proper assembly or
operation, contact your dealer or representative.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Worksaver HPD-16 HFL
Summary of Contents for Worksaver HPD-16 HFL
- Page 1 OWNER’S / OPERATOR’S MANUAL MODEL NO.’s HPD-16 MFL HPD-16 HFL HPD-20 MFL HPD-20 HFL Model HPD-20 MFL Shown CAUTION For Safe Operation FRONT LOADER MOUNTED Read Rules And Instructions Carefully HYDRAULIC POST DRIVERS SINO LEEINGLES, PIDA AYUDA Safety Instructions Assembly & Mounting...
-
Page 2: Table Of Contents
Like all mechanical products, it will require cleaning and upkeep. Lubricate the Post Driver as specified. Use only genuine Worksaver, Inc. service parts. Substitute parts will void the warranty and may not meet stan- dards required for safe and satisfactory operation. Record the model and serial number of your Post Driver here: Model:________________________________________ Serial Number:_______________________________ RETAIL CUSTOMER’S RESPONSIBILITY... -
Page 3: Warranty
2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident. 3. If parts not made or supplied by Worksaver have been used in connection with the unit, if, in sole judge- ment of Worksaver such use affects its performance, stability, or reliability. -
Page 4: Safety Information
To the Owner/Operator/Dealer All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded opera- tor who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. - Page 5 SAFETY INSTRUCTIONS (continued) EQUIPMENT SAFETY GUIDELINES Safety of the operator is one of the main concerns in designing and developing a new piece of equipment. Designers and manufacturers build in as many safety features as possible. However, every year many accidents occur which could have been avoided by a few seconds of thought and a more careful approach to handling equipment.
- Page 6 SAFETY INSTRUCTIONS (continued) SAFETY SIGNS Keep safety signs clean and legible at all times. Replace safety signs that are missing or have become illegible. Replaced parts that displayed a safety sign should also display the current sign. Safety signs are available from your Distributor or Dealer Parts Department or the factory. How to Install Safety Signs: •...
- Page 7 SAFETY INSTRUCTIONS (continued) Please remember it is important that you read and heed the safety signs on the post driver, and the safety rules set forth. Clean or replace all safety signs if they cannot be clearly read and understood. They are there for your safety as well as the safety of others.
- Page 8 SAFETY INSTRUCTIONS (continued) Before you operate the driver, check over all pins, bolts and connections to be sure all are securely in place. Replace any damaged or worn parts immediately. Consult local utility companies to make certain there are no buried gas lines, electrical cables, etc., in the work area before beginning operation.
- Page 9 SAFETY INSTRUCTIONS (continued) TRANSPORT SAFETY Comply with state and local laws governing highway safety and movement of farm machinery on public roads. The use of flashing amber lights is acceptable in most localities. However, some localities prohibit their use. Local laws should be checked for all highway lighting and marking requirements. When driving the tractor and equipment on the road or highway under 20 mph (32 kph) at night or during the day, use flashing amber warning lights and a slow moving vehicle (SMV) identification emblem.
- Page 10 SAFETY INSTRUCTIONS (continued) MAINTENANCE SAFETY Good maintenance is your responsibility. Poor maintenance is an invitation to trouble. Follow good shop practices. - Keep service area clean and dry. - Be sure electrical outlets and tools are properly grounded. - Use adequate light for the job at hand. Make sure there is plenty of ventilation.
- Page 11 SAFETY INSTRUCTIONS (continued) MAINTENANCE SAFETY (continued) After servicing, be sure all tools, parts and service equipment are removed. Check to ensure all safety signs are installed and in good condition. (See safety sign section for location drawing.) Do not allow grease or oil to build up on any deck or platform. Never replace hex bolts with less than grade five bolts unless otherwise specified, i.e.
- Page 12 SAFETY INSTRUCTIONS (continued) SAFETY TRAINING Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to pro- vide safe equipment can be wiped out by a single careless act of an operator. In addition to the design and configuration of equipment, hazard control and accident prevention are depend- ent upon the awareness, concern, prudence and proper training of personnel involved in the operation, trans- port, maintenance and storage of equipment.
-
Page 13: Safety Signs
SAFETY SIGNS OBEY ALL SAFETY WARNINGS NOTE: If Safety Sign is missing or damaged, replace immediately. Cylinder Locking Strap - Remove before using Post Driver 101202... -
Page 14: Preparation Instructions
The models HPD-16 HFL and HPD-20 HFL have the (order bracket #830320). driving ram positioning controlled hydraulically. A two... - Page 15 INSTRUCTIONS (continued) PACKAGING If your tractor loader has a bucket Quick Attach feature, check with your dealer on the availability of adapter The Post Driver is shipped as four (4) bundles. brackets for your brand and model loader. For pin type loader bucket mountings, the following 1.
- Page 16 INSTRUCTIONS (continued) ASSEMBLY (continued) FIG. A CAUTION! To help prevent personal injury, stand clear of frame and loader. Keep feet away from underside of main frame. 5. Attach the driving ram assembly to the manual adjust- ment base plate assembly. A chain hoist or forklift can Connect the above assembly to the loader arms using be used to stand the driving ram assembly upright to the bottom hole in the channel and attach the upper con-...
- Page 17 (6) nuts and lock FOR HYDRAULIC ADJUSTED UNITS – washers from the mounting bolts. (HPD-16 HFL and HPD-20 HFL) Align the mounting bolts with the six (6) holes in the mounting channel and secure with the nuts and lock 1.
- Page 18 INSTRUCTIONS (continued) ASSEMBLY Connect the ” I.D. x 216” long hose from the inlet (continued) side of the two spool valve to one of the tractor hydraulic remote outlets. 5. Install the hydraulic package. Refer to Figure E for cor- rect location and orientation of components.
-
Page 19: Operating Instructions
OPERATING INSTRUCTIONS ASSEMBLY • Smear grease over the exposed portion of the plated (continued) hydraulic cylinder rod after use to help prevent pitting and rust from forming. If Post Driver is going to be Now operate the hydraulic levers on the multi-spool stored outside this is very important. - Page 20 OPERATING INSTRUCTIONS (continued) OPERATION 7. Stand at a 45° angle to the post – not directly in front of the post. Be sure all bystanders are at a safe dis- Observe all operating and safety instructions in this tance from the Post Driver. manual and those on the Post Driver before using this machine.
-
Page 21: Service Instructions
OWNER SERVICE MAINTENANCE AND VALVE CONVERSION INSTRUCTIONS ADJUSTMENTS The conversion plug for making the control valve com- Make certain the safety and instruction decals are patible with closed-center hydraulic systems is shipped in attached to the Post Driver. If they are lost, damaged, or the hardware box (see Figure I). - Page 22 SERVICE INSTRUCTIONS (continued) MAINTENANCE AND 5. NOTE: It is advisable to install a new rod guide, cylin- der cap and seal as a unit when rebuilding the cylin- ADJUSTMENTS (continued) der. Also inspect the cylinder rod for pits and/or rust and replace if necessary.
-
Page 23: Specifications
Make sure driver will be located on a solid surface and Read all the safety warnings in the front of the manual. in a location away from children, animals, or traffic area. POST DRIVER SPECIFICATIONS HPD-16 MFL HPD-16 HFL HPD-20 MFL HPD-20 HFL (Manual) (Hydraulic) -
Page 24: Trouble-Shooting
TROUBLE-SHOOTING PROBLEM: DRIVER DOES NOT DRIVE A POST PROBLEM: DRIVER RAM RAISES VERY FAST AND HITS TOP URETHANE BUMPERS SOLUTIONS: SOLUTIONS: 1. The hydraulic valve return line is connected to a trac- tor remote outlet and/or a quick coupler is being used. 1. - Page 25 TROUBLE-SHOOTING (continued) PROBLEM: POST VEERS OFF AT AN ANGLE WHILE 3. Adjustable legs on mount are not setting firmly on the BEING DRIVEN ground. Re-adjust legs. SOLUTIONS: 4. Carriage springs may be disconnected or broken. 1. Top of post is not cut “square,” causing the post to drive 5.
-
Page 26: Parts Lists
HPD-16 PARTS DRAWING... - Page 27 HPD-16 PARTS LIST...
- Page 28 HPD-20 PARTS DRAWING...
- Page 29 HPD-20 PARTS LIST...
- Page 30 HYDRAULIC CONTROL VALVE & MOUNTING BRACKET PARTS DRAWING NOTE: Post Drivers prior to S/N 2656 (HPD-16) and S/N 2987 (HPD-20) used valve #814473 (Gresen).
- Page 31 HYDRAULIC CONTROL VALVE & MOUNTING BRACKET PARTS LIST...
- Page 32 ADJUSTABLE MANUAL BASE MOUNTING PACKAGE PARTS DRAWING & LIST...
- Page 33 MANUAL FRONT LOADER MOUNT PARTS DRAWING & LIST...
- Page 34 HYDRAULIC FRONT LOADER MOUNT PARTS DRAWING NOTE: Post Drivers prior to S/N 2656 (HPD-16) and S/N 3005 (HPD-20) used valve #814734 (Gresen).
- Page 35 HYDRAULIC FRONT LOADER MOUNT PARTS LIST...
- Page 36 MANUAL WHEN ORDERING REPAIR PARTS, MODEL NO.’s ALWAYS GIVE THE FOLLOWING INFORMATION: 1. PART NUMBER HPD-16 MFL 2. PART DESCRIPTION HPD-16 HFL 3. MODEL NUMBER HPD-20 MFL 4. NAME OF ITEM HPD-20 HFL CAUTION For Safe Operation MAKE EVERY DAY...
Need help?
Do you have a question about the HPD-16 HFL and is the answer not in the manual?
Questions and answers