Sony PDW-F30 Operating Instructions Manual page 42

To carry out playback again, move back to the desired clip
using the PREV button, jog dial or shuttle dial.
To set shot marks
While playing back a disc, you can set essence marks such
as SHOT MARK1 and SHOT MARK2 in desired frames.
To set a SHOT MARK1 or SHOT MARK2, hold down the
M/MARK1 or m/MARK2 button and press the SET
button.
Note
To erase or change essence marks, use the supplied
PDZ-1 Proxy Browsing Software.
Playback in jog mode
In jog mode, you can control the speed of playback by the
speed of turning the jog dial. The playback speed range is
–1 to +2 times normal speed.
To carry out playback in jog mode, proceed as follows.
ACCESS
NETWORK
LOCAL
REMOTE
LEVEL
CH 1 CH 2 CH 3 CH 4
PHONES
1
Press the JOG button, turning it on.
2
Turn the jog dial in the desired direction, at the speed
corresponding to the desired playback speed.
Playback in jog mode starts.
3
To stop playback in jog mode, stop turning the jog dial.
Normally, the unit enters jog mode as soon as you turn
the jog dial. If you want it to enter jog mode only when
you press the JOG button, set OPERATIONAL
FUNCTION >SEARCH ENABLE in the setup menu
to "VIA SEARCH KEY".
Playback in shuttle mode
In shuttle mode, you can control the speed of playback by
the angular position of the shuttle dial. The range of
playback speed is ±20 times normal speed.
To carry out playback in shuttle mode, proceed as follows.
42
Playback
F1
F2
F3
VAR
MARK1
MENU
F4 CHAPTER
SUB THUMB IN OUT
F5 EXPAND
CLIP NAIL SET RESET
JOG
PAGE DISPLAY
CLIP ESSENCE
MENU MARK MARK2
PREV PLAY NEXT STOP TS REC
SHUTTLE
KEY INHI
PRESET
PB
SHIFT
TOP F REV F FWD END STANDBY
1 2,3
ACCESS
NETWORK
LOCAL
REMOTE
LEVEL
CH 1 CH 2
PHONES
1
Press the SHUTTLE button, turning it on.
2
Turn the shuttle dial to the desired angle
corresponding to the desired playback speed.
Playback in shuttle mode starts.
3
To stop playback in shuttle mode, return the shuttle
dial to the center position, or press the STOP button.
Normally, the unit enters shuttle mode as soon as you
turn the shuttle dial.
If you want it to enter shuttle mode only when you
EJECT
press the SHUTTLE button, set OPERATIONAL
FUNCTION >SEARCH ENABLE in the setup menu
to "VIA SEARCH KEY".
To alternate between normal-speed playback and
shuttle mode playback
Set the shuttle dial to the position corresponding to the
desired shuttle playback speed, then switch between
normal-speed playback and shuttle playback by pressing
the PLAY and SHUTTLE buttons alternately.
Playback in variable-speed mode
In variable-speed mode, you can control the speed of
playback in the range of –1 to +2 times normal speed.
To carry out playback in variable-speed mode, proceed as
follows.
ACCESS
NETWORK
LOCAL
REMOTE
LEVEL
CH 1 CH 2
PHONES
1
Press the VAR button, turning it on.
2
Turn the shuttle dial to the desired angle
corresponding to the desired playback speed.
F1
F2
F3
MARK1
MENU
F4 CHAPTER
IN OUT
SUB THUMB
F5 EXPAND
SET RESET
CLIP NAIL
PAGE DISPLAY
CLIP ESSENCE
MENU MARK MARK2
PREV PLAY NEXT STOP TS REC
CH 3 CH 4 KEY INHI
PRESET
PB
SHIFT
TOP F REV F FWD END STANDBY
3
F1
F2
F3
MARK1
MENU
F4
CHAPTER
IN OUT
SUB THUMB
F5 EXPAND
SET RESET
CLIP NAIL
PAGE DISPLAY
CLIP ESSENCE
MENU MARK MARK2
PREV PLAY NEXT STOP TS REC
CH 3 CH 4 KEY INHI
PRESET
PB
SHIFT
TOP F REV F FWD END STANDBY
3
EJECT
VAR
JOG
SHUTTLE
1 2,3
1
EJECT
VAR
JOG
SHUTTLE
2,3