Download Print this page
FUTABA T6K Software Update Manual
Hide thumbs Also See for T6K:

Advertisement

Quick Links

1M23Z05202
Your Futaba T6K transmitter programming can be updated easily online. When functions are added or improved, the
update file can be downloaded from our website.
For more information, check out web site for FAQ regarding updating this product.
*The display screen is an example. The screen depends on the PC. T6K screens are subject to change without notice.
Required for update (Purchase separately)
CIU-3 or CIU-2
(for updates of 4PV optional)
CGY750/GY701/GY520
Extensions (optional)
Preparations
1.
Install the driver for the CIU-3/CIU-2 onto your PC.
When the CIU-3 is first connected to the PC, once the CIU-3 is connected to the PC, download the
recommended driver software Using Windows Vista, the "Found New Hardware Wizard" window
appears on the screen. Click "Locate and install driver software".
When the CIU-2 is first connected to the PC; the "Found New Hardware Wizard" window appears on the
screen. Install the drivers download from local Futaba Dealers Website.
Refer to the manual of the CIU-3/CIU-2 for further information.
T6K Software update manual
(optional)
DSC cord
or
(Access is possible by the web)
USB Port
- 1 -
PC
CIU-3 or CIU-2

Advertisement

loading
Need help?

Need help?

Do you have a question about the T6K and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for FUTABA T6K

  • Page 1 For more information, check out web site for FAQ regarding updating this product. *The display screen is an example. The screen depends on the PC. T6K screens are subject to change without notice. Required for update (Purchase separately)
  • Page 2: Updating Procedure

    50% or less, always recharge the battery before updating. Download the zip file of the update data from our website or your local distribtor's website. http://www.rc.futaba.co.jp Futaba WEB site CIU-3 executable file Software Update program Download CIU-2 executable file Connect as shown in the figure.
  • Page 3 CIU-3; Turn on the transmitter power while pressing down the "END" and "+" button. CIU-3 ⊕ Press the button next turn ON CIU-3 CIU-2; Turn on the transmitter power while pressing down the "END" button. CIU-2 Press the button next turn ON CIU-2 - 3 -...
  • Page 4: Double-Click

    Start an executable file by a PC. CIU-3 CIU-2 CIU-3 Double-click CIU-2 Write Wait for about 30 seconds - 3 minutes. Don't turn off the power ! - 4 -...
  • Page 5 Completed Turn off the power switch of your T6K and remove the CIU-3/CIU-2. Shut down the update software. Check the software version at [TX SETTING]. + - Turn off the power and then turn on the power while pressing the + key and – key simultaneously.
  • Page 6 Error If an error display appeared, the redo an update from the beginning. Don't disconnect or remove the battery from the transmitter during the update. It is possible that the transmitter can be damaged if the battery is unplugged during the update. In the case of a failed update, the transmitter may not restart.
  • Page 7 T6K transmitter. Please refer to the original instruction manual where applicable, but replace the steps indicated below with these instructions. Please note that the software update will be finalized the first time that the T6K is powered up, after the software has been applied. As such, it may require a few moments before the Start screen appears.
  • Page 8 Jog key for 1 below your set value. below your set value. below your set value. second. second. second. FUTABA CORPORATION Phone: +81 475 32 6982, Facsimile: +81 475 32 6983 1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba 299-4395, Japan ©FUTABA CORPORATION 2016, 12 (1)