Subscribe to Our Youtube Channel
Related Manuals for Keba KeMes A100
Summary of Contents for Keba KeMes A100
- Page 1 KeMes A100 Angle measurement device Operating instructions V 1.01 Translation of the original manual...
- Page 2 Specifications are subject to change due to further technical developments. Details presented may be subject to correction. All rights reserved. Gewerbepark Urfahr, 4041 Linz, Austria, Phone: +43 732 7090-0, KEBA AG Headquarters: Fax: +43 732 7309-10, keba@keba.com For information about our subsidiaries please look at www.keba.com.
- Page 3 A100 Record of Revision Record of Revision Changed Version Date Change in chapter Description hasl, 1.00 11-2017 Newly created sthm, hli 1.01 02-2019 Technical data Updating laser data Operating instructions V1.01 © KEBA...
- Page 4 A100 Operating instructions V1.01 © KEBA...
-
Page 5: Table Of Contents
Operation and handling ..................... General instructions ..................Selection menu on the display ................. Operating modes ..................... 5.3.1 Manual ....................5.3.2 Machine ..................... 5.3.3 MachineS ................... 5.3.4 MachineE ................... Positioning ....................... Execution of the manual measurement ............Operating instructions V1.01 © KEBA... - Page 6 10 Directives, standards and regulations ..............10.1 EU directives....................10.2 Standards......................10.2.1 EMC Directive ..................10.2.2 General procedures and safety principles ......... 10.3 Regulations ...................... 11 EU Declaration of Conformity ................... 12 Anhang: Apache License ..................Index ..........................Operating instructions V1.01 © KEBA...
-
Page 7: Introduction
KeMes A100 is intended for measuring angles between two flat surfaces and measuring sheet metal parts. KeMes A100 is intended for indoor use. KeMes A100 may only be used for the types of use detailed in the technical description and only in compliance with the described technical framework conditions. -
Page 8: Contents Of The Document
The pictured devices used in this manual are visual examples. The devices used by you may differ in their appearance. 1.4.1 Contents of the document ● Description of the device ● Operation ● Technical data Operating instructions V1.01 © KEBA... -
Page 9: Safety Notes
This symbol reminds you of the possible consequences of touching electro- statically sensitive components. Safety information Describes important safety-related requirements or informs about essential safety-related correlations. Information Identifies practical tips and useful information. No information that warns about potentially dangerous or harmful functions is contained. Operating instructions V1.01 © KEBA... -
Page 10: General Safety Notes
Safety notes A100 General safety notes Read and observe all instructions in order to work with KeMes A100 safely and without risk. The warning plates on the device must never be rendered illegible. WARNING! The following areas of application are expressly excluded for KeMes A100: ●... -
Page 11: Safety Notes For Personal Safety
If this device is damaged, the device must be taken out of commission and sent to our service partner for repair. The device must not be opened. Only the maintenance work expressly permitted by KEBA may be performed (see Chap. "Maintenance"). Operating instructions V1.01... -
Page 12: Description Of The Device
Fig. 3-1: Front view ... Display ... Operating button ... Cover of USB or charging socket ... Output for laser radiation (mirror) Rear view Fig. 3-2: Rear view ... Type plate ... Magnets ... Recesses for measuring aid Operating instructions V1.01 © KEBA... -
Page 13: Top View
... Material number, serial number, ... QR code country of origin ... Note on electronic waste ordinance ... CE mark ... Laser warning plate ... Laser class ... Do not look into the beam ... Please observe instructions Operating instructions V1.01 © KEBA... -
Page 14: Datamatrix Code
The following accessories are included in the scope of delivery: ● 1 storage case ● Short description in various languages ● 1 measuring aid with centering adapter ● 1 USB charging device with additional adapter for different countries ● 1 USB cable Operating instructions V1.01 © KEBA... -
Page 15: Displays And Operating Elements
A100 Displays and operating elements Displays and operating elements Operating panel The operator panel is on the front side of the KeMes A100. It is used for op- eration and status indication. Fig. 4-6: Control panel The operator panel consists of: ●... -
Page 16: Menu Structure
Similar to 3 / 6 MachineS, but with longer measurement duration Settings (Disc format, Clock, Brightness, Format, AutoOff, Log, MStart- 5 / 6 Settings Trig, MStopTrig, MSlow, MSpeed, MSens, MAccuracy, Reset) 6 / 6 ErrLog Error memory for messages that have occurred Operating instructions V1.01 © KEBA... -
Page 17: Operation And Handling
● Alignment of the device with the workpiece: The longitudinal axis of the housing of KeMes A100 must be aligned parallel to the bending edge and tilted as little as possible in order to be symmetrical between Operating instructions V1.01... - Page 18 Metal sheets (e.g. aluminum, steel and stainless steel (cold-rolled or descaled)) ● Galvanized sheets ● Sheets with protective foil The following material surfaces can be measured using KeMes A100 with limited accuracy only: ● Scaled sheets ● Electrolytically galvanized sheets ●...
-
Page 19: Selection Menu On The Display
● Heavily scaled sheets Selection menu on the display KeMes A100 has a selection menu on the display. During operation, the cur- rent status is shown on the display. The operating button can be used to navigate the menu. Button operation for menu navigation... - Page 20 Calibration of acceleration sensor, device must not be in motion Measurement active / Waiting for new measurement Menu 4/6 MachineE Result of automatic measurement Automatic continuous measurement for setting up the de- vice started Automatic continuous measurement Operating instructions V1.01 © KEBA...
- Page 21 ": the measurement starts as soon as the move down MStartTrig press beam moves faster than the speed set using the parameter. MSpeed " ": the measurement starts as soon as the set motion sensitivity of the MSens parameter has been exceeded. Operating instructions V1.01 © KEBA...
- Page 22 Error memory for messages that have occurred. See ErrLog errors! Chapter "Errors". KEMES A100 Switch-off and display of the installed software version v01.03 This function is started by pressing and holding the operating button. By pressing it 2x briefly, the menu item is exited again without triggering the function.
-
Page 23: Operating Modes
" operating mode, the angle at the press brake is measured. For Machine this purpose, the device must be attached to the upper tool. In " ", KeMes A100 starts by calibrating the acceleration sensor. The Machine display indicates " " until the idle state has been reached. If the up- per tool moves downward, the measurement operation is started. -
Page 24: Machines
Positioning Since the measurement principle of KeMes A100 is based on reflection, at- tention must be paid to the correct positioning of the device. During measurement, the laser beam is directed outward by a mirror. The laser beam is visible to the observer as a thin line on the measured object. -
Page 25: Execution Of The Manual Measurement
Fig. 5-8: Examples of positioning using the upper tool Execution of the manual measurement For executing a manual measurement, use of the measuring aid is recom- mended. This allows the measurement result to be reached in less time and with greater accuracy. Operating instructions V1.01 © KEBA... - Page 26 (2). Fig. 5-10: Installing the centering adapter 3) Plug the centering adapter onto the measuring aid. When doing so, the centering adapter must lock completely. Operating instructions V1.01 © KEBA...
- Page 27 5) Start the measurement (switch on the laser) by pressing the operating button once. 6) Position KeMes A100 so that the laser beam can hit both legs of the ob- ject to be measured unobstructed at an angle of 90°.
-
Page 28: Carrying Out An Automatic Measurement
Information The upper tool must be magnetic so that KeMes A100 can be installed on KeMes A100 must rest on the upper tool throughout. For the installation of KeMes A100 on the upper tool, proceed as follows: 1) Create a gap of approx. - Page 29 Carrying out the measurement WARNING! Personal injury risk due to the bending process! During the bending process, the device must not be operated! Prior to oper- ation, the press brake must be switched to a safe state. Operating instructions V1.01 © KEBA...
-
Page 30: Data Recording And Personalization
Data recording and personalization Data recording The data recording can be activated and deactivated using settings menu item in the menu. This function is deactivated 6 / 13 Log 5 / 6 Settings by default. Operating instructions V1.01 © KEBA... - Page 31 Personalization KeMes A100 can be personalized. This personalization is shown when switching on the device. In order to personalize KeMes A100, a connection to the internal memory of the device must be established. The file can then be edited using KEMES.INI...
- Page 32 NAME0=Company ;user name line 1(max. 16 char.) NAME1=Operator After editing, the file must be saved and the connection to KeMes A100 must be disconnected. The next time KeMes A100 is switched on, the entered text appears on the display. Connecting the device and PC...
-
Page 33: Diagnostics
Caution If the error does not go away or cannot be acknowledged, the device must be sent back to the service partner for diagnostics and repair. Operating instructions V1.01 © KEBA... -
Page 34: Maintenance
Information When charging KeMes A100, faults on the power supply in an industrial en- vironment line can impair the charging process. If this impairment occurs repeatedly, then charging in a business environment, e.g. in an office space, as well as selective testing of the network quality is recommended. - Page 35 A100 Maintenance In case of non-use, it is recommended to keep KeMes A100 in its included case to protect the device from dust. If the device malfunctions despite careful preparation and test procedures, it must be sent back to the service partner for repair.
-
Page 36: Disposal
● The materials are recyclable in accordance with their labeling. You can make an important contribution to protecting our envi- ronment by reusing, renewing and recycling materials and old appliances. Operating instructions V1.01 © KEBA... -
Page 37: Technical Data
Measuring positions with the following measured distances between the mirror and workpiece surface: 25 mm and 25 mm / 100 mm and 100 mm / 25 mm and 140 mm / 140 mm and 25 mm Operating instructions V1.01 © KEBA... -
Page 38: Environmental Conditions
IEC 60825-1:2014, Tabelle 10, Bedingung 3: pulse duration in measuring aperture) Charging device Designation: Switching Power Supply Model: PSAI05R-050QL6 Operating voltage: 100 - 240 V AC, 50 - 60 Hz Operating current: 300 mA Charging voltage: +5 V Operating instructions V1.01 © KEBA... -
Page 39: Usb Cable
Fig. 9-12: Front view of measuring aid with centering adapter ... Guide tab for attaching to the de- ... Centering adapter vice Dimensions, weight Height: 162 mm Width: 49 mm Depth: 15 mm Weight: 75 g Operating instructions V1.01 © KEBA... -
Page 40: Directives, Standards And Regulations
In order to comply with the duty to communicate information in accordance with Article 33 of the REACH regulation, detailed information on the ingredi- ents are provided on our web page. For more detailed information, please contact KEBA. Operating instructions V1.01 © KEBA... -
Page 41: Eu Declaration Of Conformity
A100 EU Declaration of Conformity EU Declaration of Conformity Operating instructions V1.01 © KEBA... -
Page 42: Anhang: Apache License
"Not a Contribution." "Contributor" shall mean Licensor and any individual or Legal Entity on behalf of whom a Contribution has been received by Licensor and subsequently incorporated within the Work Operating instructions V1.01 © KEBA... - Page 43 You to the Licensor shall be under the terms and conditions of this License, without any additional terms or conditions. Notwithstanding the above, nothing herein shall supersede or modify the terms of any separate license agreement you may have executed with Licensor regarding such Contributions. Operating instructions V1.01 © KEBA...
- Page 44 License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License. Operating instructions V1.01 © KEBA...
-
Page 45: Index
Manual (manual operating mode) ... 23 DataMatrix code Measuring aid General .......... 14 Installation........... 26 Dimensions, weight Menu Technical data ........ 39 Navigation........... 19 Display............. 15 Structure .......... 19 Menu ........... 19 Position .......... 12 Operating instructions V1.01 © KEBA... - Page 46 MachineE (automatic operating mode).. 24 Scope of delivery ........ 14 MachineS (automatic operating mode)..Status indicator........ 15 24 Manual (manual operating mode).. 23 Type plate Operation.......... 15 General .......... 13 Output for laser radiation Position .......... 12 Operating instructions V1.01 © KEBA...
Need help?
Do you have a question about the KeMes A100 and is the answer not in the manual?
Questions and answers