Adjusting The Speaker Volume - Sony DVP-NS90V Operating Instructions Manual

Be sure to change the value in the Setup
Display each time you move the speakers.
Start from the front speaker. The default
adjustments are in parentheses.
FRONT
Set this between 4 and 50 ft
(10 ft/3m)
(1.2m and 15.2m) in 1 ft
(0.3m) increments.
CENTER (10 ft/ Set this within –5 and +2 ft
3m)
(–1.5m and +0.6m) of the
"FRONT" setting in 1 ft
(0.3m) increments. For
example, if "FRONT" is set
to 17 ft (5.1m), "CENTER"
can be set between 12 and
19 ft (3.6m and 5.7m).
REAR (10 ft/
Set this within –16 and
3m)
+2 ft (–4.8m and +0.6m) of
the "FRONT" setting in 1 ft
(0.3m) increments. For
example, if "FRONT" is set
to 17 ft (5.1m), "REAR"
can be set between 1 and
19 ft (0.3m and 5.7m).
SUBWOOFER
Set this within –5 and +2 ft
(10 ft/3m)
(–1.5m and 0.6m) of the
"FRONT" setting in 1 ft
(0.3m) increments. For
example, if "FRONT" is set
to 17 ft (5.1m),
"SUBWOOFER" can be
set between 12 and 19 ft
(3.6m and 5.7m).
Note
If each of the front or rear speakers are not placed at
an equal distance from your listening position, set
the distance according to the closest speaker.
LEVEL (FRONT)
Varies the level of the front speakers. Be sure
to set "TEST TONE" to "ON" for easy
adjustment.
The default adjustments are in parentheses.
L (0 dB) Set this between –6 dB and 0
dB in 0.5 dB increments.
R (0 dB)
Set this between –6 dB and 0
dB in 0.5 dB increments.
CENTER
Set this between –12 dB and
(0 dB)
0 dB in 0.5 dB increments.
SUBWOOFER
Set this between –15 dB and
(DVD: –5 dB/ +5 dB in 0.5 dB increments.
Super Audio
CD: 0 dB)
LEVEL (REAR)
Varies the level of the rear speakers. Be sure
to set "TEST TONE" to "ON" for easy
adjustment.
The default adjustments are in parentheses.
L (0 dB)
Set this between –12 dB and
0 dB in 0.5 dB increments.
R (0 dB)
Set this between –12 dB and
0 dB in 0.5 dB increments.
To adjust the volume of all the speakers at
one time
Use the amplifier's (receiver's) volume
control.
TEST TONE
The speakers will emit a test tone. Use this
when you use the 5.1CH OUTPUT jacks and
adjust "LEVEL (FRONT)" and "LEVEL
(REAR)."
OFF The test tone is not emitted
from the speakers.
ON
The test tone is emitted from
each speaker in sequence while
adjusting level.

Adjusting the speaker volume

and level
1
Select "SPEAKER SETUP" in the Setup
Display.
2
Select "TEST TONE" and set to "ON."
You will hear the test tone from each
speaker in sequence.
3
From your listening position, select
"LEVEL (FRONT)" or "LEVEL (REAR)"
and adjust the value using X/x.
The test tone is emitted from both left and
right speakers simultaneously.
4
Select "TEST TONE" and set to "OFF"
to turn off the test tone.
Note
The test tone signals are not output from the
DIGITAL OUT (COAXIAL or OPTICAL)/HDMI
OUT jack.
77