Patlite LR6-IL Operation Manual

Patlite LR6-IL Operation Manual

Io-link signal tower

Advertisement

Quick Links

Notice to Customer
Thank you very much for purchasing our PATLITE
products.
 Request the installation and wiring be performed by
a professional contractor if construction work is
involved.
 Prior to installation, read this manual thoroughly
before using this product to ensure correct use.
 If there are any questions concerning this product,
refer to the contact information at the end of this
document and contact your nearest PATLITE Sales
Representative.
To the Contractor
 Read this manual carefully prior to installation.
 Be sure to return this manual to the customer.
Signal Tower
LR6-IL
TYPE
Complete Operation
Installation
1 Read this First
2 Model Number Confi guration
3 Names and Dimensions
4 Installation
5 Wiring
6 How to Use
7 Buzzer Settings
8 Detaching the Unit
9 Troubleshooting
10 Specifi cations
11 Service Parts
12 Optional Parts
– 1 –
GA0001002_02
Manual
Operation Maintenance
Page
2
2
3
4
6
7
9
10
22
23
25
26

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LR6-IL and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Patlite LR6-IL

  • Page 1 5 Wiring 6 How to Use 7 Buzzer Settings Notice to Customer 8 Detaching the Unit Thank you very much for purchasing our PATLITE products. 9 Troubleshooting  Request the installation and wiring be performed by  a professional contractor if construction work is involved.
  • Page 2: Read This First

    Read this First Safety Precautions The safety precautions that should always be followed in order to prevent injury to user or other individuals as well as prevent damage to property are described below.  The level of injury or damage caused by ignoring these safety precautions and using the product improperly is categorized ...
  • Page 3 Names and Dimensions  WM Direct Mount/M12 Connector Specifi cations (3-point Screw Attachment)  (Unit: mm) Part Name Material LR6-3ILWMNW Head Cover LED Unit Globe: PC Body M12 Bracket Direct Mount Bracket Waterproof Packing Silicone Rubber * M12 connector cable is sold separately. (Please use an M12 connector of Φ16 or less.) Accessory LR6 - WM...
  • Page 4: Installation

    Installation Notice  The following requirements are necessary for a proper mounting location.  - Location with strong and even surface with minimal vibration.   Install with the mounting direction in the upright position.   When the installation location is unavoidably irregular and waterproof performance is required, use a sealant between ...
  • Page 5  WC Installation Figure (1/2” NPT Installation Figure)  While holding part ‘A’, install the 1/2” NPT. Failure to comply may result in damage. 1/2” NPT Recommended Torque 2.25 N·m  Mounting Dimensional Drawing  (Unit: mm) Mounting Hole Φ31 15°...
  • Page 6 Wiring Warning  Ensure the proper working voltage is used and that direct current or alternating current is properly applied.  Any mistake in wiring may result in damage or fi re. Caution  Do not pull the wire, or stuff it inside of this product. Possible cause of failure may occur. ...
  • Page 7: How To Use

    How to Use This product is an IO-Link compliant product. Connect this product by following the “ Wiring” (p. 6). The controller can light, fl ash or extinguish the LEDs or control the buzzer. Changing the “Operating Mode” settings enables the following modes: ...
  • Page 8  The intermittent buzzer and the LED pattern do not synchronize.   Parameter Settings  For information about the parameter settings, please download the IODD from the LR6-IL page on our homepage (https:// www.patlite.com/). Please also download and use the parameter sheet in the same way. – 8 –...
  • Page 9: Buzzer Settings

    Buzzer Settings  Do not use excess force when performing operations. Failure to comply will result in damage due  to breakage or deformation. Caution  Do not use sharp-pointed objects to perform operations. Failure to comply may result in damage ...
  • Page 10 Detaching the Unit Follow the procedure below to detach a unit, such as when removing the Buzzer Unit or changing the layout of the LED Units. Link to Video Caution  Be sure that it is disconnected from the power source before working on it. ...
  • Page 11 <LED/Buzzer Unit>  Removal  LED Unit or Buzzer Unit Turn the body or LED unit counter-clockwise to unlock, then raise upwards to remove it.  Positioning Mark  <Locked> <Unlocked> Body or LED Unit  Attachment  Align the Positioning Mark after insertion, then turn the unit clockwise to lock it.
  • Page 12 <Body Unit>  Removal  While holding the Direct Mount Bracket, turn the M12 Bracket counter-clockwise, until it unlocks, then pull it upwards to remove.  Positioning Mark  M12 Bracket <Locked> <Unlocked> Direct Mount Bracket  Attachment  Align the Positioning Mark after insertion, then turn the unit clockwise to lock it.
  • Page 13 <Troubleshooting the Buzzer Unit Attachment> The Buzzer Unit is generally in the status shown in the diagram below after removal. Buzzer Unit Groove Positioning Mark LED Unit Buzzer Unit (Detached) Bottom View Body The rib inside of the Buzzer Unit fi ts into the groove when the Buzzer Unit has been removed from the product.
  • Page 14 Use the procedure below if the Buzzer Unit does not attach properly. Turn the part inside the Buzzer Unit in the counter-clockwise direction. Turn until the rib fi ts into the groove, then attach the Buzzer Unit to the product. Turn this part in the counter-clockwise direction.
  • Page 15 <Example for LED Unit Reconfi guration>  Moving an LED Unit lower  1 Remove the LED Unit right above the LED 2 Turn the LED Unit to remove counter- Unit in the area to remove. clockwise while holding the adjacent LED unit to release the lock, then pull upward.
  • Page 16  Adding an LED Unit  1 Remove the LED Unit above the area to 2 Align the positioning marks and insert the attach an additional LED unit. LED Unit, then turn the LED Unit clockwise to lock it in place. 3 Align the positioning marks and insert the LED Unit that was removed in , then turn the...
  • Page 17  Changing the Position of an LED Unit  1 Remove the LED Unit right above the 2 Remove the LED Unit that will be changing LED Unit that will be changing postitions. positions. 3 Remove the LED Unit right above the 4 Attach the LED Unit that was removed in position to add the LED unit.
  • Page 18 5 Attach the LED Unit that was 6 Attach the LED Unit that was removed in removed in – 18 –...
  • Page 19 <Troubleshooting the LED Unit> The structure of the LED Unit is indicated below. Status Condition Lens LED Unit Rib/Groove Positioning Mark Rib/Groove Body LED Unit (Detached) Top View The rib of the lens generally fi ts into the groove when the LED Unit has been removed from the product.
  • Page 20 Caution Check whether the rib of the lens inside of the LED Unit fi ts into the groove if the LED Unit does not attach properly. Attach the LED Unit by referring to the next page if the rib does not fi t into the groove as shown in the diagram below. In addition, the rib may slide out of the groove during removal as shown in the diagram below depending on how the LED Unit is removed.
  • Page 21 Use the procedure below if the LED Unit does not attach properly. Turn the lens inside the LED Unit in the counter-clockwise direction. Turn until the lens snaps in place, and then attach the LED Unit to the product. Lens LED Unit Bottom View Lens...
  • Page 22: Troubleshooting

    Buzzer Unit to the product by referring to “ Detaching the Unit” (p. 10-21). Check the “Information for Inquiries,” and then contact the nearest PATLITE Sales Representative if you cannot resolve the problem even after the above troubleshooting. Information for Inquiries Product Name...
  • Page 23: Specifications

    Specifi cations General Specifi cations Model LR6-3ILWMNW-RYG Rated Voltage 24 V DC Voltage tolerance range 18 V DC to 30 V DC Standard 170 mA Rated current consumption Maximum 200 mA Standard Rated power consumption Maximum Inrush current 10 A / 0.3 msec Ambient operating temperature -20 °C to +50 °C Ambient operating humidity...
  • Page 24 Model LR6-ILWMNW LR6-ILWCNW Rated Voltage 24 V DC Voltage tolerance range 18 V DC to 30 V DC Standard 170 mA Rated current consumption Maximum 200 mA Standard Rated power consumption Maximum Inrush current 10 A / 0.3 msec Ambient operating temperature -20 °C to +50 °C Ambient operating humidity 90 % RH or less;...
  • Page 25: Service Parts

    Service Parts These are the various parts for the customer to use when repairing or replacing parts for the product. O-ring 60 Head Cover 60 [W/A] Shading Sheet 60 5 pcs. 5 pcs. – 25 –...
  • Page 26: Optional Parts

    Optional Parts The optional parts for this product are listed below. (Top line: Part Name; Bottom: Model) Model Number Confi guration LED Unit LR6-E LED Unit Globe Model Color Color 6 - E - Model Number Amber Green Blue White Multicolor* (None) Colored Globe...
  • Page 27 Model Number Confi guration Buzzer Unit LR6-BW Body Color Model (Material) 6 - B Model Number Off-white (PC) External Diagram General Specifi cations (Unit: mm) Model LR6-BW Ambient operating -20 °C to +50 °C temperature Ambient operating humidity 90 % RH or less; No condensation Mass 0.060 kg (Tolerance: ±10 %)
  • Page 28 Model Number Confi guration Wireless Data Communication System Transmitter Model Compatible WDT-6LR-Z2 Product WDT - - Z2 Model Number LR Model Signal Tower Size: Φ60 External Diagram General Specifi cations (Unit: mm) Model WDT-6LR-Z2 Ambient operating -20 °C to +50 °C temperature Ambient operating humidity 85 % RH or less;...
  • Page 29 The optional parts for attachment are listed in the following table: Pole Bracket Wall Mounting Bracket Wall Mounting Bracket SZP-004W SZK-001U SZK-003W Mounting Bracket Mounting Bracket Aluminum Pole SZ-010 SZ-016A POLE-[100/300/800]A21 – 29 –...

Table of Contents