Jacuzzi J-300 Installation Manual And Use & Maintenance page 38

mode that will only activate the heater during the daytime called
"DAY" mode.
Note: The heater will activate when the temperature drops 2°
from the set temperature.
Economy mode is an energy-saving program. The heating cycle
may be activated any time between 5 pm and 7 am every day.
This time cannot be programmed.
• In Day mode the heating cycle may be activated any time
between 7 am and 5 pm. This time cannot be programmed.
• Auto Mode allows the heater to heat, at all times, in order to
maintain the preset temperature.
Programming the Heating Mode
To change the programmed heating mode:
Note: If no button is pressed within 5 seconds of each selection
the screen will revert back to the Main Menu and the current set-
tings will remain active.
1. Press ( ) until you get to the "HEAT" Menu. The display will
scroll "HEATER MODE." The system returns to the main menu if
no action is taken.
2. Press or to prepare the system for changes. Continually
press to scroll through the following modes:
• Economy Mode: The screen will display "ECO" and scroll
"ECONOMY MODE. "
• Day Mode: The screen will display "DAY" and scroll "DAY
MODE. "
• Auto Mode: The screen will display "AUTO" and scroll "AUTO
MODE. "
3. Once a selection is made, press (
the setting. The system will return to the "HEATER MODE" Menu.
Configuring cleaning/filter replacement reminders
A programmable filter timer can be set to remind you when to
clean or replace the filters.
• The default setting is for 180 days.
• The timer range is from 0 to 180 days, in increments of 10
days.
Note: we do not recommend deactivating this function.
Programming or resetting the timer.
Note: If no button is pressed within 5 seconds of each selection
the screen will revert back to the Main Menu and the current set-
tings will remain active.
1. Press ( ) until you get to the "FC" Menu. The display will
scroll "FILTER CHANGE." The system returns to the main menu if
no action is taken.
2. Press or to prepare the system for changes. Continually
press to adjust the length of time for the timer.
3. Once you select the number of days, press (
selection. The system will return to the "FILTER CHANGE" Menu.
4. Once the timer expires the display will alternate between the
water temperature and "CHANGE FILTER".
) to confirm and activate
1
) to confirm this
1
Programming the CLEARRAY Timer
A programmable change bulb timer can be set to remind you
when to when it is time to replace the UV bulb for the CLEARRAY
system.
• The default setting is for 365 days.
• The timer range is from 0 to 365 days, in increments of 10
days.
Note: we do not recommend deactivating this function.
Programming or resetting the timer.
Note: If no button is pressed within 5 seconds of each selection
the screen will revert back to the Main Menu and the current set-
tings will remain active.
1. Press ( ) until you get to the "UV" Menu. The display will
scroll "CLEARRAY BULB."The system returns to the main menu
if no action is taken.
2. Press or to prepare the system for changes. Continually
press to adjust the length of time for the timer.
3. Once you select the number of days, press (
selection. The system will return to the "CLEARRAY BULB" Menu.
4. Once the timer expires the display will alternate between the
water temperature and "CHANGE CLEARRAY BULB".
Configuring reminders for changing the water
A programmable water refresh timer can be set to remind you
when to when it is time to drain and refill your spa.
• The default setting is for 180 days.
• The timer range is from 0 to 180 days, in increments of 30 days.
Note: we do not recommend deactivating this function.
Programming or resetting the timer.
Note: If no button is pressed within 5 seconds of each selection
the screen will revert back to the Main Menu and the current set-
tings will remain active.
1. Press ( ) until you get to the "H2O" Menu. The display will
scroll "WATER REFRESH." The system returns to the main menu
if no action is taken.
2. Press or to prepare the system for changes. Continually
press to adjust the length of time for the timer.
3. Once you select the number of days, press (
selection. The system will return to the "WATER REFRESH" Menu.
4. Once the timer expires the display will alternate between the
water temperature and "CHANGE WATER".
Programming the Time
To program the time, follow the steps below:
Note: If no button is pressed within 5 seconds of each selection
the screen will revert back to the Main Menu and the current set-
tings will remain active.
1. Press ( ) until you get to the "TIME" Menu. The display will
scroll "SET TIME." The system returns to the main menu if no ac-
tion is taken.
2. Press or to display the current time.
3. Press or to prepare the system for changes.
38
) to confirm this
1
) to confirm this
1