Table of Contents
Related Manuals for Abus SHMK10000
Summary of Contents for Abus SHMK10000
- Page 1 SHMK10000 ABUS Z-Wave Magnetic contact Important information and FAQs about this product and other products can be found on the website www.abus.com Version 1.0 Original operating instructions in English. Keep for future use!
-
Page 2: Table Of Contents
English Summary Introduction ............................3 1.1. Declaration of Conformity ......................3 1.2. Disclaimer of Liability ....................... 3 Important Safety Informations ......................4 2.1. Intended Use ........................... 4 2.2. Unboxing ..........................4 2.3. Installation location / operating environment ................4 2.4. Children ........................... -
Page 3: Introduction
Your rights are limited to the repair or replacement of this product as delivered. ABUS Security Center assumes no liability for any special, incidental or consequential... -
Page 4: Important Safety Informations
English 2. Important Safety Informations 2.1. Intended Use Only use the device for the purpose for which it was built and designed. Any other use is considered unintended. All guarantee claims are invalid in the event of damage caused by non- compliance with this safety information. -
Page 5: Important Information On Battery Disposal
English The battery must not be directly exposed to heat or sunlight, and must not be stored in a place with a very high temperature. The battery must not come into contact with water. The battery must not be dismantled, pierced or otherwise damaged. The battery contacts must not be short-circuited. -
Page 6: Product Introduction
For CR2 Batterien (3V DC) 3.3 Operating principle The SHMK10000 was developed for use in home automation systems that use the Z- Wave wireless standard. The sensor enables the monitoring of windows and doors and can be installed comfortably without drilling and wiring thanks to battery operation and adhesive mounting. -
Page 7: Performance Features
The integrated sabotage button also reliably reports possible manipulation attempts to the gateway. 3.3. Performance features The ABUS Z-Wave SHMK10000...: …is a battery-operated radio magnetic contact …is Z-Wave PLUS compatible & certified …supports the Z-Wave S2 Standard (Security 2) -
Page 8: Mounting & Installation
English Press the Tamper-button 3 times within 1.5 seconds and the Status-LED on the base unit front will flash 3 times The App will show if the Add device process was successful and the Status-LED will turn Repeat the inclusion process from step B if it was not successful. -
Page 9: Exclusion / Remove Device
English Center the magnet on the sensor (see marking strip). When the sensor is opened or closed, the status LED lights up once. 4.3. Exclusion / Remove Device Click the - (Remove) button in your Z-Wave App and follow the further instructions Press the Tamper-button 3 times within 1.5 seconds and the Status-LED on the base unit front will flash 3 times... -
Page 10: Reset (Factory-Reset)
English 4.4. Reset (Factory-Reset) 1. Press the Tamper-button 3 times within 1.5 Seconds 2. The device is now restored to factory settings Note: 1, This procedure should only be used if the primary gateway is not capable of acting. 2, If the multi-sensor is set to the factory setting, the status is set to "not included", the association settings... -
Page 11: Unterstützte Command Classes
Battery Version 1 Security 2 Version 1 Supervision Version 1 Wake Up Version 2 6. Technical Specifications Parameters Unit SHMK10000 Dimensions 72 x 21 x 26 (Sensor) / 35 x 11 x 13 (Magnet) Weight 0 – 40 Operating Temperature °C Max. - Page 12 English Security S2 Classes Z-Wave Chip Generation Z-Wave Sensor-Typ Open/Closed (Binary) Routing Slave Zwave library type Notification sensor / Device Type / Role type Reporting sleeping slave...