Complete Installation; Commissioning The Product; Commissioning Requirements; Service Menu - Grundfos AQtap Installation And Operating Instructions Manual

4.11 Complete installation

1. Write the SIM card phone number on the back of the AQtap
installation and operating instructions.
2. Place the AQtap installation and operating instructions in the
AQtap cabinet.
3. Close the AQtap cabinet and lock it with the standard cabinet
key and one of the unique keys.
– Keep the unique keys securely, spare keys cannot be
purchased. We recommend to keep one key as a master for
copies in a safe place.
4. Open the shut-off valve.
5. Switch on the electrical power supply.
6. Attach the water tapping guide near the AQtap.
– The water tapping guide gives a short introduction to water
tapping for WaterCard holders.

5. Commissioning the product

AQtap water dispensers can only be operated after
commissioning. The AQtap is automatically assigned to the same
WMS group as the ServiceCard used for commissioning.
For more information on Water Management System (WMS) see
7.10 Water Management System (WMS) and the manual which
you can find online in the help section of WMS.

5.1 Commissioning requirements

• Installed AQtap, see 4. Installing the product
• Activated ServiceCard, see 3.3.3 Starter package
• SIM card to connect to WMS, see 4.7 SIM card preparation
and installation.
• SAT (site acceptance test) by means of the service menu /
ServiceCard and performance test.

5.2 Service menu

For information on the user interface see 7.7 AQtap user
interface.
The AQtap service menu can be accessed with the assigned
ServiceCard. It is used for:
• commissioning
• testing the buttons and lights
• setting the water price
• reading out warning and alarm codes
• restarting or resetting the AQtap
5.2.1 Entering the service menu
For first commissioning, decide on a 4-digit PIN
Note
code. This code cannot be changed later!
To end the service menu, remove the ServiceCard
Note
at any point.
1. Place the ServiceCard on the right smart card reader.
2. Enter PIN code.
3. Press "OK" to go to the next menu item.
5.2.2 Alarms
1. Alarm sign (red) and alarms are displayed:
– The last 10 alarms are kept in a log, "1E" is the newest
alarm, "10E" the oldest alarm.
– The 3-digit code corresponds with a certain alarm.
– The alarm sign is flashing when a current alarm is displayed,
it is permanently lit for obsolete alarms.
– To jump between alarms, press the "up" and "down" button.
– For further details see section 11.1.2 Alarms.
2. Press "OK" to go to the next menu item.
5.2.3 Warnings
1. Warning sign (yellow) and warnings are displayed:
– The last 10 warnings are kept in a log, "1E" is the newest
alarm, "10E" the oldest warning.
– The 3-digit code corresponds with a certain warning.
– The warning sign is blinking when a current warning is
displayed, it is permanently lit for obsolete warnings.
– To jump between warnings press the "up" and "down"
button.
– For further details see section 11.1.1 Warnings.
2. Press "OK" to go to the next menu item.
5.2.4 Water price
1. Water price icon and current water price per litre are
displayed:
– Press "left" and "right" button to select a figure or decimal
point.
– Press "up" and "down" to change a figure or position of the
decimal point.
2. Press "OK" to save the new value.
– The new water price flashes three times to indicate
successful change.
– The next menu item opens automatically.
5.2.5 Water pressure
1. Water pressure icon and current inlet water pressure in bar
are displayed,
2. Press "OK" to go to the next menu item.
5.2.6 Light test
1. All lights (icons, figures and buttons) are displayed.
2. Press "OK" to go to the next menu item, or after 1 minute, the
next menu item opens automatically.
5.2.7 Buttons test
1. One after the other, all buttons are lit:
– Press the lit button to check the function and change to the
next button, then press next button...
– The order of appearance is: "water button", "download",
"up", "right", "down", "left", "OK" button.
2. Service menu is restarted.
– Press "OK" to go to the next menu item, or remove the
ServiceCard.

5.3 Performance test

1. Place a graduated canister under the water outlet.
2. Place the ServiceCard on the left smart card reader,
– 99999 and water credits is displayed in the left part of the
big display.
– The "water button" is lit.
3. Press "water button" to start water tapping.
– Let the water flow until the AQtap is deaerated.
4. Press "water button" to stop tapping water.
5. Empty the canister and place it again under the water outlet.
6. Press "water button" to start water tapping.
– Watch tapped amount of water being counted up in the left
part of the big display until 10 l is displayed.
7. Press "water button" to stop water tapping.
8. Check if tapped amount of water corresponds to the water in
the graduated canister.

6. Starting up the product

AQtap is ready for operation after commissioning with the
ServiceCard.
11