CONTENTS Sublimation Oven 1.1 Overview 1.2 Technical Data 1.3 Safety Arrangements of the 3D Sublimation Oven 1.4 Safety Arrangements at the workplace Installation 2.1 First Time Use 2.2 Installation Working with the 3D Sublimation Oven 3.1 Quality Guarantee and Support 3.2 Setting Parameters 3.3 Recommended Settings 3.4 Placing the Jigs...
3D SUBLIMATION OVEN 1.1 Overvieuw Ventilation grill Baseplate and product jigs Control display Handle Drawer Main switch Main fuse power cable with connector...
3D SUBLIMATION OVEN 1.2 Techical Data Press Dimension: 55,6 x 67,5 x 33,5 cm Weight: 48 KG Operating Voltage: 230 VAC Rated Power: 1500 W Fuse: 10A Max. Temperature: 180°C Temperature Range: 0 - 180°C Max. Bar: -1 Bar 1.3 Safety Arrangements of the 3D Sublimaton Oven The oven is equipped with different safety arrangements, to make a safe usage possible.
2.1 First Time Use Important Precautions and Recommendations After having unpacked the Technotape 3D oven, check to ensure Warning that it is not damaged. In case of doubt, do not use it and When correctly installed, your product meets all safety require- consult your supplier or a professionally quali ed technician.
WORKING WITH THE SUBLIMATION OVEN 3.1 Quality Guarantee and Support 3.2 Setting Parameters Technotape can only offer support for the 3D Sublimation Oven After switching on the oven, make sure that the drawer is when it’s used in combination with a Virtuoso VJ-628 (Mutoh) open to adjust the settings.
Image 3.2.8 Image 3.2.9 3.3 Recommended Settings 3.4 Placing the Jigs The followings standards are recommended for the Technotape Install the jig pin in the baseplate, fasten by hand and place the 3D Sublimation Phone Cases production jig(s) accordingly. NOTE: these standards apply for usage stated under Quality NOTE: After exchanging a production jig make sure it is Guarantee and Service (see 3.1).
WORKING WITH THE 3D SUBLIMATION OVEN 3.5 Get Started Close the drawer of the oven to start pre-heating (see image 3.5.10). When the drawer is closed the oven will start the pre-heating process (see image 3.5.11). After the pre-heating process the display will show: “Ready”...
MAINTAINANCE 4.1 Maintainance Switch off the oven and take the power cable out of the wall outlet. The oven must be cooled before any maintenance. 4.2 Replacing the Main Fuse If the oven does not work and the main switch is on, check the main fuse. To change the main fuse;...
The lters are placed inside the oven. On the back of the oven there are two housings for holding the lters. The lters-houses can be opened by hand. New lters can be ordered at www.technotape.com article: 3DT.SUB.AIR.FT1 NOTE: Always replace both lters at the same time.
MAINTAINANCE EC-Conformance-Declaration after EC-guideline for machines 2006/46 EC Techn-O-Parts B.V. Tolweg 7 3741 LM Baarn The Netherlands Hereby declares that the following machine: 3D Sublimation Oven with Serial Number 3 D V 0 3 N Is compliant with the speci cations of the following EC directives: Machinery (2006/46) Low Voltage (2006/95) EMC (2004/108)
Page 18
Technotape International +31 (0)35 541 80 94 Tolweg 7 +31 (0)35 541 18 17 3741 LM Baarn of ce@technotape.com The Netherlands W www.technotape.com...