Summary of Contents for IFM Electronic Ecomat 300 AC422S
Page 1
Original Device Manual Fail-safe SmartPLC AC4S with EtherNet/IP interface AC422S for ISO 13849 up to PL e for IEC 62061 up to SIL CL 3 Firmware: 4.0.2 English...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Contents Contents Preliminary note Legal and copyright information ................... 7 Purpose of the document ..................... 7 Symbols and formats used ....................8 Overview: User documentation for AC4S ................9 Modification history ......................
Page 3
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Contents Menu view ..........................56 5.2.1 Menu navigation ......................... 56 5.2.2 Navigation aids ........................... 57 Page view ...........................59 5.3.1 Navigate on a page ........................59 5.3.2 Use navigation aids ........................59 5.3.3 Description of the control elements ....................
Page 4
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Contents Notes on the firmware update ..................156 Connect and address AS-i slaves ..................156 Setup of EtherNet/IP ......................156 Setup of the configuration interface .................157 Replace standard AS-i slave ....................157 Replace safe AS-i slave ....................158 Troubleshooting Status LED ........................160...
Page 5
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Contents Index ifm weltweit • ifm worldwide • ifm à l’échelle internationale...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Preliminary note Legal and copyright information Preliminary note Legal and copyright information ....................... 7 Purpose of the document ......................... 7 Symbols and formats used ........................8 Overview: User documentation for AC4S ....................9 Modification history ...........................
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Preliminary note Symbols and formats used > Symbols and formats used 15989 WARNING Death or serious irreversible injuries may result. CAUTION Slight reversible injuries may result. NOTICE Property damage is to be expected or may result. Important note Non-compliance can result in malfunction or interference Information...
Preliminary note Overview: User documentation for AC4S > Overview: User documentation for AC4S 18655 ifm electronic provides the following user documentation for the models of the device class "Fail-safe SmartPLC AC4S": Document Content / Description Data sheet Technical data of AC422S as a table ...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Safety instructions Modification history Safety instructions Required background knowledge ......................11 Please note .............................11 Tampering with the unit ..........................12 Start-up behaviour of the controller ......................12...
WARNING Non-observance of these instructions can lead to property damage or personal injury. ifm electronic gmbh does not assume any liability in this regard. ► The acting person must have read and understood the safety instructions and the corresponding chapters in this manual before working on and with this device.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Safety instructions Tampering with the unit > Tampering with the unit 11242 WARNING Tampering with the units can affect the safety of operators and machinery. Tampering with the units is not allowed. In case of non-compliance our liability and warranty expire.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 System description Start-up behaviour of the controller System description Intended use ............................14 Information concerning the device ......................15 Hardware ..............................22 Software..............................33 8697 This chapter describes the structure and the components of the system.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 System description Intended use > Intended use 5310 NOTICE Danger when device is overloaded or incorrectly used. The device and / or the associated machine / plant may be damaged or destroyed or may malfunction if the limits of the "Technical data"...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 System description Information concerning the device > Information concerning the device Where is what on the AS-i device? ......................16 Operating elements ..........................17 Display elements ............................17 Interfaces ..............................18 Type label ...............................21 Required accessories ..........................21 5330...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 System description Information concerning the device > 3.2.1 Where is what on the AS-i device? 8719 Legend: Display Status LED (H1) 2 function keys 4 arrow keys Connector (X1) for AS-i 1, AS-i 2, functional earth Connector (X2) for AUX Local inputs and outputs (X4)
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 System description Information concerning the device > 3.2.2 Operating elements 15840 The device provides the following operating elements. > Arrow and function keys 15867 Below the display is the key panel with two function keys and four arrow keys. The operator controls the Graphical User Interface (GUI) of the device with the keys.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 System description Information concerning the device > 3.2.4 Interfaces Ethernet configuration interface ......................19 Local input/output interface ........................19 SD card slot ............................20 EtherNet/IP fieldbus interface .........................20 7134 AC422S has the following interfaces.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 System description Information concerning the device > Ethernet configuration interface 6982 The configuration interface (X3) is located behind the front flap of the device. It allows the user to access the following device functions: ...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 System description Information concerning the device Possible combinations of input and output channels 12095 The inputs IN1...IN8 can be configured both as safe and non-safe inputs. The outputs OUT1...OUT4 can be configured both as safe and non-safe outputs. This permits the following minimum or maximum input and output combinations: Min.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 System description Information concerning the device > 3.2.5 Type label 19822 The type label is on the right housing side of the device. It provides the following information: QR code for product website CE/cULus marking Protection class...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 System description Hardware > 3.3.1 Safety architecture System architecture ..........................24 Process safety time ..........................27 Diagnostic coverage DC and MTTFd value ...................28 19815...
Page 24
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 System description Hardware > System architecture 20485 The hardware structure of the safety module of AC422S corresponds to the implementation to DIN EN ISO 13849-1:2008, IEC 62061:2010 and IEC61508:2010 with a two-channel architecture with hardware fault tolerance (HFT = 1).
Page 25
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 System description Hardware > Main module 19837 The main module is the central component of AC422S. It contains the recovery system and the firmware of the device and controls the communication between the individual system components via the backplane.
Page 26
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 System description Hardware > Safety module 19840 The safety module contains the safety-related hardware of AC422S. The architecture of the safety module provides the following structural features: 1oo2 hardware architecture (1 out of 2 architecture) ...
Page 27
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 System description Hardware > Process safety time 19839 The process safety time depends on the source and the objective of the request, the signal processing and the transmission length. ►...
Page 28
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 System description Hardware > Diagnostic coverage DC and MTTFd value 19841 The diagnostic coverage (DC) of AC422S is: 95 % The MTTFd value of AC422S is: 100 years The CCF value of AC422S is: 5 %...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 System description Hardware > 3.3.2 Operating states of AC422S 19835 AC422S has the following operating states: INIT NORMAL OPERATION SYSTEM STOP Below the state chart: ...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 System description Hardware > 3.3.3 Monitoring and securing mechanisms 19836 > System start / power on reset 19842 When the voltage supply has been applied, the safety module of AC422S automatically undergoes a power-on built-in test (PBIT).
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 System description Hardware > 3.3.4 Error detection and processing 19838 > Error classes 19849 AC422S recognises the following error classes: > Fatal error 19847 The following errors are classified as fatal errors: ...
Page 32
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 System description Hardware > Safe state 19851 The safety module of AC422S is always in the safe state. Exceptions are the following operating states of the fail-safe PLC: ...
3.4.3 Certified software components for safe applications 19821 To program safe applications for AC422S ifm electronic provides certified software components for the programming environment CODESYS safety 3.5. In addition, the user can use the function libraries supplied with CODESYS safety.
Page 35
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Installation Software Installation Installation...............................36 Electrical connection ..........................36 Connect devices to local I/O interface ....................38 10257 This chapter informs about the connection of devices to the local I/O interface.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Installation Installation > Installation 14343 The unit must be connected by a qualified electrician. Environmental conditions Observe the environmental conditions for the installation (→ (→ page 168))! Ensure a condensation-free environment. Avoid excessive dust, vibration and shock.
19823 ► Supply the device with a voltage of 24 V DC (18...32 SELV/PELV) (e.g. from the 24 V DN3011 power supply from ifm electronic). The connection is made to the terminals X2. The max. cable length is 3 m.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Installation Connect devices to local I/O interface > Connect devices to local I/O interface Safety instructions ..........................39 Supported connection types ........................40 Supported device types ..........................41 Install safe device to local I/O interface ....................52 Install standard device on local I/O interface..................52 17640...
IN4 and IN5 ifm electronic does not assume any guarantee for obtaining the required SIL / cat. / PL if other than the above-mentioned input combinations is used. ► Use one of the above-mentioned input combinations for the connection of 2-channel sensors.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Installation Connect devices to local I/O interface > 4.3.2 Supported connection types 11234 The local I/O interface of AC422S supports the connection of safe and non-safe devices. The following connection methods are possible: Connection method Description...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Installation Connect devices to local I/O interface > 4.3.4 Install safe device to local I/O interface 17700 To install a safe device to the local I/O interface: ► Observe the safety instructions. (→ Safety instructions (→...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Connect devices to local I/O interface Operation Control of the graphical user interface ....................54 Menu view...............................56 Page view ...............................59 Remote access ............................72 14805...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Control of the graphical user interface > Control of the graphical user interface 6930 Below the display is the key panel with six membrane keys. The operator controls the graphical user interface of the device with these keys.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Control of the graphical user interface > 5.1.1 Function keys 7090 The two function keys allow the operator to trigger specified actions (e.g. tick a checkbox). The function of the function keys changes depending on the context.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Menu view > Menu view 6996 The menu view allows the user to select the menu page with the required control or display function. Legend: Info bar Main navigation bar Subnavigation bar 1 Subnavigation bar 2...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Menu view > 5.2.2 Navigation aids 15830 The following screen elements help you navigate through the menu: > The info bar shows the navigation path of the selected menu symbol. >...
Page 58
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Menu view 6. ► Use [] to select the [Setup] menu symbol. > The focus is on the [Setup] menu symbol. ► Press the [Select] function key to go to the page view of the [Setup] menu item.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Page view > Page view 7959 The page view allows the user to select and execute a requested function. Legend: Info bar Main navigation bar Page Scroll bar Tab menu Page element with focus Navigation status bar with...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Page view > 5.3.3 Description of the control elements Tab menu/Tab ............................61 Button ..............................62 Checkbox ..............................62 List ................................63 Slave selector ............................64 Confirmation message ..........................69 Numerical field ............................70 Binary field ..............................71 7013 A page consists of different control elements.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Page view > Tab menu/Tab 8737 A tab menu groups together the different functions of a menu page. A tab menu consists of at least two tabs. A tab combines related functions. Example: >...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Page view > Button 14196 A button allows the operator to carry out a specified action once. The caption on the button describes the action. Example: Use: Select a button ►...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Page view > List 7042 A list provides a set of defined values. The operator can select precisely one value from this set (= 1 of n selection). Examples: = list without caption = list with caption...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Page view > Slave selector Overview of slave states .........................65 Overview of free slave addresses ......................67 7018 The slave selector is used to select an AS-i slave or an AS-i address. Legend: Indicator of AS-i master operating mode AS-i address symbol...
Page 65
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Page view > Overview of slave states 6992 > The slave selector shows an overview of the slaves in the selected AS-i network. > The symbol colour signals the slave status. Meaning of symbols and colours: →...
Page 66
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Page view > Slave status: colour code + symbols 11236 Single slave A/B slave Colour Meaning grey No slave found: slave address is neither in the LPS nor in the LDS green Slave is activated ( in LAS) Configuration error type 1:...
Page 67
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Page view > Overview of free slave addresses 6993 In this overview, the slave selector shows the free and occupied AS-i addresses. > The symbol colour indicates the state of the AS-i address. Meaning of symbols and colours: Free slave addresses: colour code + symbols →...
Page 68
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Page view > Free slave addresses: colour code + symbols 11239 Single slave A/B slave Colour Meaning Prio. grey Slave address is already used. turquoise Address is free according to LDS (= no slave found), however: address already belongs to a stored projection (= application profile).
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Page view > Confirmation message 7033 The confirmation message is a security prompt. It appears when important changes are made to the system settings. The confirmation message shows the changes made. For the changes to become effective, they first need to be acknowledged by the operator.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Page view > Numerical field 7046 The numerical field allows the operator to enter integer values. The value range is context-specific. Numerical fields are part of the following GUI elements: Control element Example Meaning...
Page 71
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Page view Adopt the set values ► Use [Select] function key to confirm the set values and to leave the edit mode. Use [Back] function key to reset the set values and to leave the edit mode. >...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Remote access > Remote access General ..............................73 Recommended browsers ........................73 Operating instructions ..........................74 7068 The device has an integrated web server. It generates a web interface which allows remote access to all device functions via an web browser.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Remote access > 5.4.1 General 7069 The operating concept of the web interface follows the same philosophy as the operating concept of the local display. The web interface uses the same menu items, the same menu structure and the same symbols as the graphic user interface of the local display.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Remote access > 5.4.3 Operating instructions Web interface: Access 10283 ► PC / Laptop / mobile device: Start Internet browser. ► Internet browser: Enter IP address of the device in the address line (e.g.
Page 75
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Remote access > Web interface: Password protection 14187 The web server has a basic password protection to prevent unwanted or unauthorised changes to the device settings via the web interface. When the web interface is accessed, a status bar at the top shows if the user is logged in or logged out: User is logged in:...
Page 76
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Operation Remote access > Disconnect from web interface 14276 To log out of the web interface: ► Start web interface > Status line with status message is displayed at the top of the web interface: ►...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Remote access Menu Start screen ............................78 Quick setup .............................79 AS-i 1 / AS-i 2 ............................89 System ..............................100 Interfaces ..............................120 Safety ..............................136 ifm system solutions ..........................147 18788 This chapter describes the menu functions of the device’s graphical user interface.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Start screen > Start screen 14439 When starting the device, the start screen of the graphical user interface appears (special case: Start screen 'Basic settings' system start after initial commissioning or firmware update: → (→...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Quick setup > Quick setup 7273 The [Quick setup] menu provides fast access to the most important device functions. Navigation path Functions Quick setup: Project AS-i networks →...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Quick setup > 6.2.1 Quick setup: Project AS-i networks 8973 During projection adaptation, the AS-i master carries out the following actions: The configuration data of all detected AS-i slaves (LDS) is saved ...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Quick setup > 6.2.2 Quick setup: Configure the operating mode of the AS-i masters 8974 Operating modes of the AS-i Information regarding the operating modes of an AS-i master:→ master (→...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Quick setup > 6.2.3 Quick setup: Configure the output access 17867 Only one control instance at a time can have write access to the outputs of the connected AS-i slaves. The operator configures the control instance with the parameter [Output access].
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Quick setup > 6.2.5 Quick setup: Configure the EtherNet/IP interface 12131 The device provides the following options for configuration of the EtherNet/IP interface: The operator sets the interface parameters (IP address, network mask, Manual = gateway address) manually.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Quick setup Configure the IP parameters automatically ► From the list [IP mode], select either DHCP or BOOTP. ► Press [Accept] to save the changes. > The device receives the IP parameters from a DHCP or BOOTP server. The automatic configuration of the interface can take up to 10 seconds.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Quick setup > 6.2.7 Quick setup: Set the configuration interface 8991 The device provides the following options for configuration of the EtherNet configuration interface: The operator sets the interface parameters (IP address, network mask, Manual = gateway address) manually.
Page 86
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Quick setup – [Subnet mask] – [Gateway address] ► Press [Accept] to save the changes. ► Continue with → step 5 Configure the IP parameters automatically ► Check [Optain IP address autom.]. ►...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Quick setup > 6.2.8 Quick setup: Address the AS-i slaves connected to AS-i master 1 8992 To change the address of an AS-i slave connected to AS-i master 1: Select the menu page ►...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Quick setup > 6.2.9 Quick setup: Address the AS-i slaves connected to AS-i master 2 11671 To change the address of an AS-i slave connected to AS-i master 2 Select the menu page ►...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu AS-i 1 / AS-i 2 > AS-i 1 / AS-i 2 15912 The [AS-i 1] / [AS-i 2] menus provide access to configuration and diagnosis functions of the AS-i network components.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu AS-i 1 / AS-i 2 > 6.3.1 AS-i 1 / AS-i 2: Master setup 8996 The menu item [Master setup] provides access to the configuration options of the selected AS-i master.
Page 91
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu AS-i 1 / AS-i 2 > Carry out a projection adaptation 8938 During projection adaptation, the AS-i master stores the configuration of all AS-i slaves currently found on the AS-i network in its memory and assigns a valid AS-i address to each of them.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu AS-i 1 / AS-i 2 > 6.3.2 AS-i 1 / AS-i 2: Diagnosis 9039 The [Diagnosis] menu provides access to the diagnostic data of the selected AS-i network. >...
Page 93
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu AS-i 1 / AS-i 2 > Display the voltage supply analysis 9088 To display the voltage supply analysis: Select the menu page ► > > ► Select [Power supply] tab. Display the voltage supply analysis >...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu AS-i 1 / AS-i 2 > 6.3.3 AS-i 1 / AS-i 2: AS-i slaves 9037 The [AS-i Slaves] menu provides access to information and configuration options of the AS-i slaves. The scope of configuration options shown ([Data] and [Setup] tab) varies according to the status of the selected AS-i slaves.
Page 95
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu AS-i 1 / AS-i 2 Digital output 15974 Designation Meaning Example / Possible values [Outputs] Current values of the digital outputs (binary and hexadecimal representation) Data bit is switched off (0 / OFF) Data bit is switched on (1 / ON) ...
Page 96
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu AS-i 1 / AS-i 2 Change the digital output values manually 10939 WARNING Risk of personal injury! Risk of material damage to the machine/plant! The operator is responsible for any consequences caused by the manual change of the digital ouput values! ►...
Page 97
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu AS-i 1 / AS-i 2 > Show AS-i slave information 10935 To display information about an AS-i slave: Select the menu page ► > > ► Select an AS-i slave (→ Slave selector (→...
Page 98
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu AS-i 1 / AS-i 2 > Change an AS-i slave address 10944 To change the address of an AS-i slave: Select the menu page ► > > ►...
Page 99
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu AS-i 1 / AS-i 2 > Change the Extended ID1 of the AS-i slave 10952 To set the Extended ID1 of an AS-i slave: Select the menu page ►...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu System > System 10979 The [System] menu provides access to functions that allow configuration of the system and the device-internal standard PLC. Navigation path Functions Device-internal standard PLC →...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu System > 6.4.1 System: Programmable Logic Controller (PLC) 8955 The [PLC] menu provides access to the device-internal standard PLC. Navigation path Functions standard PLC information: → Display the status of the CODESYS standard PLC (→...
Page 102
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu System > PLC: Information 11778 The [Information] menu item provides access to the standard PLC status and project information. > Display the status of the CODESYS standard PLC 14841 To display information about the current status of the device-internal standard PLC: Select the menu page...
Page 103
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu System > PLC: Settings 16217 The [Settings] menu item provides access to the standard PLC applications (apps) on the device. > Control a single standard PLC application 14846 [App x/y] –...
Page 104
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu System > Control standard PLC applications 14847 To control all standard PLC applications stored on the device: Select the menu page ► > > ► Select [All applications] tab. Display status information about the standard PLC applications >...
Page 105
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu System > Show target visualisation 9055 Using the CODESYS programming system, the user can optionally program a target visualisation to create an application-specific user interface for the display of AC422S. The target visualisation is loaded onto the device together with the CODESYS project, but it must be activated manually.
Page 106
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu System > PLC: Diagnosis 10936 The [Diagnosis] menu item provides access to diagnostic data of the device-internal standard PLC. > Show memory used 14845 To display information about the memory capacity currently used: Select the menu page ►...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu System > 6.4.2 System: Information 7281 The [Information] menu item provides access to the version information about the system components. > Show version information 11774 To display information about the hardware and software components of the device: Select the menu page >...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu System > 6.4.3 System: Setup 7274 The [Setup] menu item provides access to the configuration options of the system. > Set output access 18627 To set the control instance for the outputs of the AS-i slaves: Select the menu page >...
Page 109
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu System > Set the device cycle 8571 NOTICE Risk of material damage to the machine/plant! A device cycle that is too short can have undesirable effects on the correct transmission of the process and control data between the PLC and peripheral devices (higher-level PLC, AS-i slaves).
Page 110
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu System > Switch the menu language 7088 To select the language of the GUI texts: Select the menu page ► > ► Select [System settings] tab. Select the menu language >...
Page 111
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu System > Set the behaviour of the display 9107 To set the display behaviour (screen saver, behaviour in case of inactivity): Select the menu page ► > ►...
Page 112
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu System > Set the system time 10954 The system time consists of date and time. The device provides the following options for setting the system time: The operator sets the date and time manually.
Page 113
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu System > Set the system time manually 10963 To set the system time manually: Select the menu page ► > ► Select [Clock] tab. Deactivate the NTP client of the device ►...
Page 114
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu System > Synchronise the system time with an NTP server 10969 To synchronise the system time with an NTP server: To synchronise the system time and date via Network Time Protocol (NTP), connect the configuration interface of the device to an NTP server directly or over a network.
Page 115
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu System > Adopt the system time of the PC 15756 This function can only be executed via the web interface of the device. To adopt the date and time of a PC/laptop: Go to the web interface of the device ►...
Page 116
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu System > Clone device configuration 7276 AC422S makes it possible to create an image of the current device configuration, to transfer it to another device and activate there (clone). The export/import of the configuration file is made via an SD card.
Page 117
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu System > Restore the device configuration 16200 NOTICE Risk of data loss and undesirable system behaviour! If the import of the device configuration is interrupted (e.g. because the device is disconnected from the electric circuit), not all the configuration data will saved on the device.
Page 118
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu System > Store diagnostic protocol 7040 Using the diagnostic protocol, the user can archive the current device configuration or provide all relevant information to the service staff via the device settings. The diagnostic protocol contains the following information in the selected user language: ...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu System > 6.4.4 System: Diagnosis 9053: The [Diagnosis] menu item provides access to the diagnostic data of the device. > Display diagnostic data 15827 To display the diagnostic data of the device: Select the menu page >...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Interfaces > Interfaces 15143 The [Interfaces] menu provides access to the configuration options of the device's interfaces. Navigation path Functions Configuration interface → Configure the IP parameters manually (→...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Interfaces > 6.5.1 Interfaces: Configuration interface 7279 The [Configuration interface] menu provides access to the settings of the EtherNet configuration interface (port X3). > Notes on IP settings 14856 The device provides the following options for configuration of the Ethernet configuration interface: ...
Page 122
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Interfaces > Configure the IP parameters manually 14860 To configure the IP parameters of the configuration interface manually: Select the menu page ► > ► Select [IP setup] tab. Deactivate the NTP client ►...
Page 123
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Interfaces Show EtherNet information 14857 To show Ethernet information regarding the configuration interface: Select the menu page ► > ► Select [Ethernet informationen] tab. Show Ethernet information >...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Interfaces > 6.5.2 Interfaces: EtherNet/IP interface 16197 The [EtherNet/IP] menu provides access to information, settings and diagnostic data of the EtherNet/IP interface. Navigation path Functions EtherNet/IP information →...
Page 125
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Interfaces > EtherNet/IP: Information 11781 The menu item [Information] provides access to information regarding the EtherNet/IP interface. > Show information 12166 To display information about the EtherNet/IP interface: Select the menu page ►...
Page 126
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Interfaces > Display EtherNet/IP data 12168 To display the EtherNet/IP data: Select the menu page ► > > ► Select [Data] tab. Display EtherNet/IP data > Page shows the following information: Designation Meaning Possible values...
Page 127
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Interfaces > Download the device and I/O description 12194 Remote access This function is only available via the web-interface of the device (→ (→ page 72)). Requirements: ►...
Page 128
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Interfaces > EtherNet/IP: Setup 16196 The [Setup] menu item provides access to the configuration options of the EtherNet/IP interface. > Notes on IP settings 12228 The device provides the following options for configuration of the EtherNet/IP interface: ...
Page 129
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Interfaces > Configure the IP parameters manually 15883 To manually configure the IP parameters of the EtherNet/IP interface: Select the menu page ► > > ► Select [Fieldbus] tab. Activate the manual configuration ►...
Page 130
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Interfaces > Set the configuration mode 15884 configuration mode More information: → (→ page 371) To set the configuration mode of the device: Select the menu page >...
Page 131
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Interfaces > Set the device-specific parameters 15909 The parameters can only be changed if the configuration mode is set to Independent (→ the configuration mode (→ page 130)). To set the device-specific parameters: set the number of channels to be transmitted per analogue input slave: Select the menu page...
Page 132
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Interfaces Set the failsafe state ► Set the following parameter as required: Parameter Meaning Possible values [Failsafe state] Behaviour of the slave Hold outputs = The outputs hold the values which outputs in case of an were present immediately before interrupted EtherNet/IP...
Page 133
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Interfaces > Set the EtherNet/IP module configuration 12230 NOTICE Risk of data loss! For the transmission of cyclic process data between the device and the EtherNet/IP PLC, a limited number of data words is available for each direction of transmission: ...
Page 134
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Interfaces Set the EtherNet/IP slots for the analogue inputs and outputs of the AS-i slaves ► Set the following parameters as required: Parameter Meaning Possible values → Slot 9 –...
Page 135
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Interfaces > EtherNet/IP: Diagnosis 9126 The menu item [Diagnosis] provides access to the diagnostic data of the EtherNet/IP interface: > Display diagnostic data 15875 To display the diagnostic data of the EtherNet/IP interfaces: Select the menu page ►...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Safety Safety 18912 The [Safety] menu provides access to the status and diagnostic information of the safety-relevant PLC of the device. Navigation path Functions AS-i 1 master settings: →...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Safety > 6.6.1 Safety: AS-i 1 master settings 9019 The [AS-i 1 master settings] menu page provides access to diagnostic data and switching states of the safe AS-i input slaves on AS-i master 1. >...
Page 138
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Safety > Configuration status: Colour codes + symbols 18273 Symbol Colour Description yellow No safe configuration available green safe configuration available > Diagnostic data: Colour codes + symbols 10926 Symbol Colour...
Page 139
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Safety > Display switching states of the safe AS-i input slaves 14851 The menu page shows switching states of the safe AS-i slaves on the selected AS-i master. Select menu page ►...
Page 140
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Safety > Meaning of the colour combinations 15872 Symbol Colour Description – switches S1 and S2 are open grey – the two code half-sequences have been taught grey –...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Safety > 6.6.2 Safety: AS-i 2 master settings 9014 The [AS-i 2 master settings] menu page provides access to diagnostic data and switching states of the safe AS-i input slaves on AS-i master 2. The menu functions correspond to the functions of the [AS-i 1 master settings] menu.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Safety > 6.6.3 Safety: Local IOs 16661 The [local IOs]menu page provides access to information about the switching states of the local inputs and outputs. > Display the switching states of the local inputs 15874 To display the switching states of the local inputs: Select menu page...
Page 143
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Safety > Switching states of the inputs: Colour codes + symbols 11776 Symbol Colour Description grey Local input is switched off green Local input is switched on >...
Page 144
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Safety > Display the switching states of the local outputs 9022 To display the switching states of the local outputs: Select menu page ► > ► Select [Local outputs] tab. Display the switching states of the local outputs >...
Page 145
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Safety > Switching states of the local outputs: Colour codes + symbols 18799 Symbol Colour Description grey Local output is switched off green Local output is switched on >...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu Safety > 6.6.4 Safety: System 15913 The [System] menu page provides access to status information of the fail-safe PLC of AC422S. > Display status information of the fail-safe PLC 14852 To display status information of the fail-safe PLC: Select menu page...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu ifm system solutions > ifm system solutions 7065 This menu is only available via the web interface of AC422S. Remote access → (→ page 72) The [ifm system solutions] menu provides access to information and installation options for ifm system solutions.
6.7.1 Notes on ifm system solutions 7053 With the AC422S, ifm electronic offers different system solutions for the simple implementation of typical applications. System solutions consist of applications which are processed by the device-internal CODESYS standard PLC. ifm system solutions and user-created standard applications must not be stored and run simultaneously on the AC422S! ►...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu ifm system solutions > 6.7.2 Show information about installed ifm apps 9041 In order to display information about the ifm system solutions installed on the device: Select menu page ►...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu ifm system solutions > All ifm system solutions and CODESYS standard PLC applications on the device are deleted. > The selected single/basic app is installed. > The progress bar indicates the status of the installation process. >...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Menu ifm system solutions > 6.7.5 Update ifm apps 6925 The user can update an ifm system solution installed on the device by overwriting it with the new version of the ifm system solution.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Setup ifm system solutions Setup Mounting and electrical connection ......................153 Install devices on the local I/O interface ....................153 Start screen 'Basic settings' ........................154 Notes on the firmware update ......................156 Connect and address AS-i slaves ......................156 Setup of EtherNet/IP ..........................156 Setup of the configuration interface ......................157...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Setup Start screen 'Basic settings' > Start screen 'Basic settings' 11226 The 'Basic settings' start screen appears after the following actions/events: initial setup firmware update data loss due to battery failure The basic settings provide access to the GUI texts, system time, etc.
Page 155
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Setup Start screen 'Basic settings' Option 2: Synchronise the system time with an NTP server ► Activate [Activate NTP] checkbox. > Status LED = ► Enter the IP address of the NTP server in the IP address field.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Setup Notes on the firmware update > Notes on the firmware update 13545 An update of the firmware of AC422S must only be made by an authorised employee of ifm electronic gmbh.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Setup Setup of the configuration interface Setup of the configuration interface 9006 To set up the EtherNet configuration interface (X3): > ► ► Select [IP setup] tab. ► Set the interface parameters (→ Notes on IP settings (→...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Setup Replace safe AS-i slave > Replace safe AS-i slave 18612 AC422S makes it possible to replace an AS-i slave with a new safe AS-i slave in the operating mode "protected mode".
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Troubleshooting Replace safe AS-i slave Troubleshooting Status LED ............................160 Online diagnosis function ........................161 Online Support Centre (OSC) ......................162 Availability of the fail-safe PLC ......................165 Display diagnostic protocol ........................165 7288 This chapter offers information regarding fault detection and troubleshooting.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Troubleshooting Status LED > Status LED 7094 The status LEDs of the device provide information about the current state of system components. Where is what on the AS-i device? Position of the status LED on device: →...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Troubleshooting Online diagnosis function > Online diagnosis function 7055 The device offers an online diagnosis function. It helps the user to find and eliminate the source of occuring failures and errors. >...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Troubleshooting Online Support Centre (OSC) > Online Support Centre (OSC) 11385 The online support centre (OSC) shows detailed information about occurring events, interference and errors. The OSC appears as follows: List to select the filter and the name of the selected filter Message A message consists of error symbol, time stamp and error...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Troubleshooting Online Support Centre (OSC) > 8.3.1 OSC: Aktuelle Meldungen zeigen 14279 The [Current] tab lists all current messages. The messages are in chronological order. Alle messages regarding warnings and errors are displayed. Under [Current] only messages will be displayed, that are created in the non-safe part of the AC422S.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Troubleshooting Online Support Centre (OSC) > 8.3.2 OSC: Show message history 11775 The [History] tab lists all messages which occurred during the operating time of the device. The messages are shown in chronological order.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Troubleshooting Availability of the fail-safe PLC > Availability of the fail-safe PLC 20705 The [Safety] menu symbol indicates the availability of the fail-safe PLC. Symbol Description Fail-safe PLC of AC422S operating reliably. ...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Address assignment in Ethernet networks > Address assignment in Ethernet networks 14436 In the Ethernet network every IP address MUST be unique. The following IP addresses are reserved for network-internal purposes and are therefore not allowed as an address for participants: nnn.nnn.nnn.0 | nnn.nnn.nnn.255.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Configuration interface: connection concepts > Configuration interface: connection concepts Direct link ..............................174 Connection via Ethernet network ......................175 7071 To be able to access the web interface and the programming interface of the device-internal PLC, the configuration interface (X3) must be connected to a computer.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Configuration interface: connection concepts > 9.3.1 Direct link 12551 To establish a direct connection to the device: ► Connect configuration interface X3 of the device with the Ethernet interface of the PC/laptop. ►...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Configuration interface: connection concepts > 9.3.2 Connection via Ethernet network 12553 To establish a connection via a Ethernet network, the device has to be connected with a coupling element (e.g.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix AS-i master > AS-i master Operating modes of the AS-i master ....................177 Master flags ............................179 8900 Master = Handles the complete organisation on the bus. The master decides on the bus access time and polls the →slaves cyclically.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix AS-i master > 9.4.1 Operating modes of the AS-i master Protected mode ............................178 Projection mode ............................178 Switch operating modes ........................178 8934 The AS-i master can be operated in one of the following operating modes:...
Page 178
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix AS-i master > Protected mode 14833 In the operating mode "Protected mode" (= normal mode), the AS-i master only communicates with AS-i slaves that are entered in the list of projected slaves (LPS) and where current and target configuration match.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix AS-i master > 9.4.2 Master flags AS-i master status flags ........................180 Execution control flags .........................181 Host flags ..............................182 DAE/EE flags ............................183 16936 The master flags contain information about the status of the AS-i master and the fieldbus host. The master flags are transmitted along with the input data of the digital AS-i slaves in the acyclic data DS2 –...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix AS-i master > AS-i master status flags 7160 The AS-i master status flags provide information about the status of the AS-i master. After a status change, the AS-i master immediately updates the flags. The AS-i master status flags are saved in the following register: AS-i master status flags –...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix AS-i master > Execution control flags 7161 The execution control flags provide information about the execution control of the AS-i master. The flags are updated by the AS-i master immediately after each change. The execution control flags are saved in the following register: Execution control flags –...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix AS-i master Flag Designation Description Initial value at power-on CCOK CTT_Config_OK 1 (TRUE): The configuration of all CTT slaves on the 0 (FALSE) network corresponds to the projected CCT data.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix AS-i master > DAE/EE flags 16935 The DAE/EE flags indicate if the double address detection and the earth fault detection are on. The DEA/EE flags are saved in the following register: DAE/EE flags active active...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix AS-i slaves > AS-i slaves Profiles of AS-i slaves ...........................185 8893 Slave = Passive participant on the bus, only replies on request of the →master. Slaves have a clearly defined and unique →address in the bus.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix AS-i slaves > 9.5.1 Profiles of AS-i slaves Configuration data (CDI) of the slaves (slave profiles) .................186 Slave profiles for slaves with combined transaction ................193 Combined transaction – Use of analogue channels in the gateway depending on the slave profile ...194 8902...
Page 186
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix AS-i slaves > Configuration data (CDI) of the slaves (slave profiles) Structure of the slave profile .........................187 Description of the IO code for digital slaves ..................187 Description of the ID code (selection) ....................188 Description of the extended ID code 1 ....................188 Description of the extended ID code 2 ....................189 Valid combinations IO code / ID code / extended ID code 2 ..............190...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix AS-i slaves > Structure of the slave profile 5347 The slave profile has the following structure: S-[IO code].[ID code].[ext. ID code2] Bits 15...12 Bits 11...8 Bits 7...4 Bits 3...0 XID2 XID1...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix AS-i slaves > Description of the ID code (selection) 5351 Structure slave profile = S-x.[ID-Code].x ID code ID code (Bits Description 3…0) [hex] 0000 4 I/O connections for binary sensors and/or actuators with 1 signal each 0001 2 dual-signal I/O connections for binary sensors and/or actuators with 2 signals each 1010...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix AS-i slaves > Description of the extended ID code 2 5355 > Extended ID code 2 for analogue slaves with profile 7.3.x 5357 The extended ID code 2 is used to specify complex slaves. Structure slave profile = S-7.3.[ext.ID code2] Bit 3 Bit 2...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix AS-i slaves > Valid combinations IO code / ID code / extended ID code 2 5359 Structure slave profile = S-[IO code].[ID code].[ext. ID code2] Ext. IO code ID code ID code 2 Meaning...
Page 191
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix AS-i slaves Ext. IO code ID code ID code 2 Meaning [hex] [hex] [hex] slave operates in the "extended addressing mode" (B slave or A/B slave) slave operates in the "extended addressing mode" (B slave or A/B slave) combined slave;...
Page 192
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix AS-i slaves Ext. IO code ID code ID code 2 Meaning [hex] [hex] [hex] single actuator with monitoring: 1 binary output + 3 binary inputs x = any value (0...F) Devices with M4 master profile enable connection of slaves with more than 4 digital inputs/outputs.
Page 193
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix AS-i slaves > Slave profiles for slaves with combined transaction 5362 Structure slave profile = S-[IO-Code].[ID-Code].[ext.ID-Code2] Slave Master Assignment analogue channels in the Bits Additional Combined D0…D3 profile profile device...
Page 194
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix AS-i slaves > Combined transaction – Use of analogue channels in the gateway depending on the slave profile 5366 Number Analogue input channels Analogue output channels Slave Slave Transaction channel...
Page 195
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix AS-i slaves...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Fieldbus EtherNet/IP Fieldbus objects ............................197 Fieldbus parameters ..........................199 Device-specific parameters ........................200 Cyclic data ............................221 Acyclic data ............................254 Configuration mode ..........................371 13070 The Ethernet Industrial Protocol (EtherNet/IP) is a fieldbus system for industrial process communication in the automation technology.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > 9.6.1 Fieldbus objects 12947 EtherNet/IP is based on the Common Industrial Protocol (CIP). CIP encloses services and applications in so-called object classes. Each object class has certain features (attributes) and defined interfaces which can be used to access the functions of the object instance.
Page 198
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Parameter data 12620 The paramater data is transfered via the Configuration Assembly Object: Object Instanc Attribute Content Access max. class [dec] r = read no. of [dec] [dec] w = write...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > 9.6.2 Fieldbus parameters 17999 The fieldbus parameters provide information for the integration of the device into the EtherNet/IP network. The fieldbus parameters are set directly on the device. Parameter Meaning Value range...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > 9.6.3 Device-specific parameters Parameters: Independent mode ......................201 Parameters: Top-down mode .......................202 Parameter setting via the configuration assembly object ..............203 EDS-file..............................220 12788 The device-specific parameters allow you to make individual adjustments to the system. Depending on the selected configuration mode, the following parameters are available.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Parameter Description Value range Change byte order Change byte order in a word Disabled* = Byte order in a word remains unchanged. Setting applies to all data of object class 4, instances 100 Enabled = Byte order in a word is inverted.
Page 204
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Device-specific parameters 12812 Data points in the Possible Default values Description configuration assembly setting values when using EDS [hex] file with EDS witho AC1421 AC1422 C.Failsafe state n=60...
Page 205
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Data points in the Possible Default values Description configuration assembly setting values when using EDS [hex] file with EDS witho AC1421 AC1422 C.11th analogue IN n=75 41 ...
Page 206
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Data points in the Possible Default values Description configuration assembly setting values when using EDS [hex] file with EDS witho AC1421 AC1422 Slot 10 81 ... 9F AS-i 2 slave 1 ...
Page 207
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Data points in the Possible Default values Description configuration assembly setting values when using EDS [hex] file with EDS witho AC1421 AC1422 C.2nd analogue n=112 41 ...
Page 208
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Data points in the Possible Default values Description configuration assembly setting values when using EDS [hex] file with EDS witho AC1421 AC1422 C.Parameter slave n=131 00 ...
Page 209
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Data points in the Possible Default values Description configuration assembly setting values when using EDS [hex] file with EDS witho AC1421 AC1422 C.Parameter slave n=154 00 ...
Page 210
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Data points in the Possible Default values Description configuration assembly setting values when using EDS [hex] file with EDS witho AC1421 AC1422 C.Parameter slave n=177 00 ...
Page 211
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Data points in the Possible Default values Description configuration assembly setting values when using EDS [hex] file with EDS witho AC1421 AC1422 C.Parameter slave n=200 00 ...
Page 212
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Data points in the Possible Default values Description configuration assembly setting values when using EDS [hex] file with EDS witho AC1421 AC1422 C.Parameter slave n=223 00 ...
Page 213
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Data points in the Possible Default values Description configuration assembly setting values when using EDS [hex] file with EDS witho AC1421 AC1422 C.Parameter slave n=246 00 ...
Page 214
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Parameters of the fieldbus slots 12811 NOTICE Risk of data loss! For the transmission of cyclic process data between the device and the EtherNet/IP PLC, a limited number of data words is available for each direction of transmission: ...
Page 215
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Slot Data points in Possible setting values Default values Description the configuration [hex] when using EDS [dec] assembly file with without AC1421 AC1422 3: digital IN AS-i 2, Slaves 01(A) ... 19(A) 3: digital IN AS-i 2, Slaves 01(A) ...
Page 216
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Slot Data points in Possible setting values Default values Description the configuration [hex] when using EDS [dec] assembly file with without AC1421 AC1422 7: digital IN AS-i 2, Slaves 01B ... 15B 7: digital IN AS-i 2, Slaves 01B ...
Page 217
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Slot Data points in Possible setting values Default values Description the configuration [hex] when using EDS [dec] assembly file with without AC1421 AC1422 10: analog IN range 2, 20 words 10: analog IN range 2, 24 words 10: analog IN range 2, 28 words 10: analog IN range 2, 32 words...
Page 218
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Slot Data points in Possible setting values Default values Description the configuration [hex] when using EDS [dec] assembly file with without AC1421 AC1422 12: analog OUT range 2, 36 words 12: analog OUT range 2, 40 words 12: analog OUT range 2, 44 words 12: analog OUT range 2, 48 words...
Page 219
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Slot Data points in Possible setting values Default values Description the configuration [hex] when using EDS [dec] assembly file with without AC1421 AC1422 14: Inputs from AC142n-PLC, 108 words 14: Inputs from AC142n-PLC, 120 words C.Slot1 n=56...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Derivation of parameter values for free slave assignment 17744 The following table shows the derivation of parameter values for a free assignment of slaves within the analogue areas.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > 9.6.4 Cyclic data 12417 The cyclic process data are updated through the fieldbus mechanisms at regular intervals. They Implicit Messaging) and are therefore real-time capable. belong to the category of implicit messaging (→...
Page 222
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > EtherNet/IP modules 12419 NOTICE Risk of data loss! For the transmission of cyclic process data between the device and the EtherNet/IP PLC, a limited number of data words is available for each direction of transmission: ...
Page 223
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Slot 1 – Digital input data single or A slaves, AS-i master 1 12428 Slot Description Value range Length [words] Digital input data of single or Empty module = Module is disabled A slaves, connected to AS-i master 1...
Page 224
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Slot 3 – Digital input data single or A slaves, AS-i master 2 12430 Slot Description Value range Length [words] Digital input data of single or Empty module = Module is disabled A slaves, connected to AS-i 01 ...
Page 225
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Slot 5 – Digital input data B slaves, AS-i master 1 12433 Slot Description Value range Length [words] Digital input data of B Empty module = Module is disabled slaves, connected to AS-i 01B ...
Page 226
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Slot 7 – Digital input data B slaves, AS-i master 2 12436 Slot Description Value range Length [words] Digital input data of B Empty module = Module is disabled slaves, connected to AS-i 01B ...
Page 227
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Mapping of the digital input/output data 13447 This table illustrates the mapping of digital input/output data of the individual slaves to the bytes of the transmitted words: Word AS-i slave addresses...
Page 228
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Table: Master flags 12475 Bits 12...15 of the first word of the digital input data contain the master flags. They provide information on the operating state of the AS-i master. The following table shows the meaning of each bit: Bit 15 Bit 14 Bit 13...
Page 229
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Slot 9 – Analogue input data 12438 Slot Description Value range Length [words] Data area with a maximum Empty module = Module is deactivated length of 60 words for cyclic 004 words = Module is activated with 4 analog channels transmission of analogue...
Page 230
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Slot 10 – Analogue input data 124390 Slot Description Value range Length [words] Data area with a maximum Empty module = Module is deactivated length of 60 words for cyclic transmission of analogue 004 words = Module is activated with 4 analog channels...
Page 231
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Slot 11 – Analogue output data 12440 Slot Description Value range Length [words] Data area with a maximum Empty module = Module is deactivated length of 60 words for cyclic 004 words = Module is activated with 4 analog channels transmission of analogue...
Page 232
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Slot 12 – Analogue output data 12442 Slot Description Value range Length [words] Data area with a maximum Empty module = Module is deactivated length of 60 words for cyclic 004 words = Module is activated with 4 analog channels transmission of analogue...
Page 233
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Configuration of the analogue channels in slots 9 ... 12 12471 The configuration of the EtherNet/IP device parameters [Analog. channels/I-slave] and [Analog. channels/O-slave] determines which analogue channels of the AS-i slaves are transmitted. The following table shows the meaning of the adjustable parameter values: Parameter values Description...
Page 234
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Table: Fixed slave assignment for slots 9 ... 12 12472 Word Word content for the following number of analogue channels per input/output slave 2 channels 1 channel 1 channel A/B-Slave Mx / slave 1(A) / Channel 1...
Page 237
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Slot 13 – Diagnostic data 12470 Slot Data length Description Value range [words] Diagnostic data sent to the I/O scanner Empty module Contents of diagnostic data: → following tables AC1421 AC1422 AC13x7 AS-i 1 *)
Page 238
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Module setting: AC1421 12624 The diagnostic data for the module settings AC1421 have 25 words. Overview diagnostic range: Word Description System diagnosis 2...5 AS-i master 1: AS-i diagnosis 6...9 AS-i master 1: list of missing slaves 10...13...
Page 239
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Diagnosis - AS-i master 1: AS-i diagnosis 12658 AS-i master 1: AS-i diagnostics: Offset Word no. PF22. PF19 CEIP CEAS CEMS Voltage AS-i+ to AS-i- in mV Voltage FE to AS-i- in mV Symmetry in % (-100% ...
Page 240
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Diagnosis - AS-i master 1: List of missing slaves 2659 AS-i master 1: list of missing slaves: Offset Word no. 15(A) 14(A) 13(A) 12(A) 11(A) 10(A) 9(A)
Page 241
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Diagnosis - AS-i master 1: List of peripheral faults 2664 AS-i master 1: list of peripheral faults: Offset Word no. 15(A) 14(A) 13(A) 12(A) 11(A) 10(A) 9(A)
Page 242
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Module setting: AC1422 2625 The diagnostic data for the module settings AC1422 have 50 words. Words 1 to 25 correspond to Module setting: AC1421 those of the module setting AC1421 (→...
Page 249
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Module setting: AC13x7 AS-i 1+2 12627 The diagnostic data for the module setting AC13x7 AS-i 1 have 25 words. Words 1 to 13 correspond Module setting: AC13x7 AS-i 1 to those of the module setting AC13x7 AS-i 1 (→...
Page 250
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Diagnosis - AS-i master 1: Master flags 12759 Diagnosis - AS-i master 1: Master flags → (→ page 247) > Diagnosis - AS-i master 1: list of detected slaves (LDS) 12760 Diagnosis - AS-i master 1: list of detected slaves (LDS) →...
Page 252
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Slot 14 – Inputs from AC4S standard PLC 17747 Slot Size Description Value range [words] Data from the Empty module = module is deactivated device-internal standard 004 words = 4 words from AC4S standard PLC to fieldbus PLC PLC to the EtherNet/IP PLC...
Page 253
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Slot 15 – Outputs to AC4S standard PLC 17746 Slot Size Description Value range [words] Data from the EtherNet/IP Empty module = module is deactivated PLC to the device-internal 004 words = 4 words from fieldbus PLC to AC4S standard PLC standard PLC...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > 9.6.5 Acyclic data Overview: acyclic data ..........................255 Acyclic data records ..........................257 Command channels ..........................283 Programmers' notes: call up acyclic services ..................370 12895 With the help of acyclic data, IO devices can be parameterised or configured, or status information can be read.
Page 255
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Overview: acyclic data 12459 The attributes in object class 801, instance 1, are preset as follows: Attribute from Content Access Numbe [dec] byte no. byte no.
Page 256
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Attribute from Content Access Numbe [dec] byte no. byte no. r = read r of [dec] [dec] w = write words M2: current configuration data CDI DS11 M2: projected configuration data PCD DS12...
Page 257
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Acyclic data records Overview: Acyclic data sets ........................258 DS1 – System information ........................259 DS2 – Digital inputs of the slaves and master flags ................260 DS3 –...
Page 258
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Overview: Acyclic data sets 17035 Data Content Access Words set no. r = read w = write System information Digital slave inputs 1(A)…31(A) and 1B…31B + master flags (status AS-i master and exec.-ctl.
Page 259
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > DS1 – System information 8753 Offset Word no. ) (byte 1) = “C" Article number ) (byte 0) = "A" Article number Article number ) (byte 2) = A Article number ) (byte 3) = A...
Page 260
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > DS2 – Digital inputs of the slaves and master flags 8754 Offset Word no. reserved Slave 1(A): D3...D0 reserved reserved reserved Slave 3(A): D3...D0 reserved Slave 2(A): D3...D0 reserved...
Page 261
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > DS3 – Analogue inputs of slaves 1(A)...15(B) 8756 Offset Word no. 0...4 Analogue input data of single slave 1 or of (slave 1A and slave 1B) 5...9 Analogue input data of single slave 2 or of (slave 2A and slave 2B) 10...14...
Page 262
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Details of the 5-word areas 8758 Offset Word no. Analogue value channel 0 of single slave x or channel 0 of slave xA Analogue value channel 1 of single slave x or channel 1 of slave xA Analogue value channel 2 of single slave x or channel 0 of slave xB Analogue value channel 3 of single slave x or channel 1 of slave xB Legend:...
Page 263
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > DS4 – Analogue inputs of slaves 16(A)...31(B) 8759 Offset Word no. 0...4 Analogue input data of single slave 16 or of (slave 16A and slave 16B) 5...9 Analogue input data of single slave 17 or of (slave 17A and slave 17B) 10...14...
Page 264
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Details of the 5-word areas 8758 Offset Word no. Analogue value channel 0 of single slave x or channel 0 of slave xA Analogue value channel 1 of single slave x or channel 1 of slave xA Analogue value channel 2 of single slave x or channel 0 of slave xB Analogue value channel 3 of single slave x or channel 1 of slave xB Legend:...
Page 265
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > DS5 – Digital outputs of the slaves 8761 Offset Word no. reserved slave 1(A): D3...D0 reserved reserved reserved Slave 3(A): D3...D0 reserved Slave 2(A): D3...D0 reserved Slave 5(A): D3...D0 reserved...
Page 266
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > DS6 – Analogue outputs of slaves 1(A)...15(B) 8763 Offset Word no. 0...3 analogue output data of single slave 1 or of (slave 1A and slave 1B) 4...7 Analogue output data of single slave 2 or of (slave 2A and slave 2B) 8...11...
Page 267
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP DS7 – Analogue outputs of slaves 16(A)...31(B) 8766 Offset Word no. 0...3 analogue output data of single slave 16 or of (slave 16A and slave 16B) 4...7 Analogue output data of single slave 17 or of (slave 17A and slave 17B) 8...11...
Page 268
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP DS8 – Status of the analogue output data of the slaves 1...31 8768 Offset Word no. reserved Status of the analogue output data of single slave 1 or of (slave 1A and slave 1B) Status of the analogue output data of single slave 2 or of (slave 2A and slave 2B) Status of the analogue output data of single slave 3 or of (slave 3A and slave 3B) Status of the analogue output data of single slave 4 or of (slave 4A and slave 4B)
Page 269
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Details of the words shown above: Offset Word no. reserved Legend: output valid 1 bit channel-independent bit "output data valid" from the slave: CTT1: 0 = more than 3.5 s have elapsed since the last update of the output values 1 = slave requests new output data within the next 3 s CTT2…CTT5:...
Page 270
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > DS9 – Slave lists LAS, LDS, LPF, LCE 8770 Offset Word no. 0...3 LAS / list of active slaves 4...7 LDS / list of detected slaves 8...11 LPF / list of slaves with periphery faults 12...15...
Page 271
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > DS11 – Current configuration data CDI 8775 Offset Word no. ID2 code ID1 code ID code IO code Slave 0 *) Slave 1(A) Slave 2(A) Slave 3(A) Slave 4(A) Slave 5(A)
Page 275
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > DS13 – Image of the input parameters of the slaves 8781 Offset Word no. reserved Slave 1(A): P3...P0 reserved reserved reserved Slave 3(A): P3...P0 reserved Slave 2(A): P3...P0 reserved...
Page 276
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > DS14 – Image of the output parameters of the slaves 8783 Offset Word no. reserved Slave 1(A): P3...P0 reserved reserved reserved Slave 3(A): P3...P0 reserved Slave 2(A): P3...P0 reserved...
Page 277
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > DS15 – Slave error counter, configuration error counter, AS-i cycle counter 8785 Offset Word no. Error counter in slave 0 Error counter in slave 1(A) Error counter in slave 2(A) Error counter in slave 3(A) Error counter in slave 4(A)
Page 278
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Offset Word no. Error counter in slave 5B Error counter in slave 6B Error counter in slave 7B Error counter in slave 8B Error counter in slave 9B Error counter in slave 10B Error counter in slave 11B Error counter in slave 12B...
Page 279
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Legend: AS-i error status ... Bit 0: Configuration error type 1 (missing slave) Bit 1: Configuration error type 2 (too many slaves) Bit 2: Configuration error type 3 (slave with wrong profile) Bit 3: Peripheral fault Bit 4:...
Page 280
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > DS17 – Error lists LCEMS, LCEAS, LDAE 15911 Offset Word no. 0...3 LCEMS (list of configuration errors - missing slaves) 4...7 LCEAS (list of configuration errors - additional slaves) 8...11 LDAE (list of double address errors) >...
Page 281
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > DS18 – Fieldbus information 17038 Offset Word no. Fieldbus state Fieldbus type Ethernet connection status Profibus slave address Profinet/EtherNet/IP IP address (byte 2) Profinet/EtherNet/IP IP address (byte 1, MSB) Profinet/EtherNet/IP IP address (byte 4, LSB) Profinet/EtherNet/IP IP address (byte 3) Profinet/EtherNet/IP subnet mask (byte 2)
Page 282
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Profinet/ IP address of the device 4 bytes One address segment per byte. EtherNet/IP e.g. 192.168.0.102 IP address Byte 1: 192 = 0xC0 Byte 2: 168 = 0xA8 Byte 3: 0 = 0x00 Byte 4: 102 = 0x66 Profinet/...
Page 283
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command channels Principle of the command channels .....................284 System commands ..........................285 AS-i master commands ........................304 16573...
Page 284
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Principle of the command channels 13543 A command channel consists of a request channel and a response channel. Command request channel (fieldbus master >>> device) Offset Word no.
Page 285
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > System commands Overview: System commands ......................286 Command 257 (0x0101) – Quick setup AS-i master 1 + 2..............287 Command 259 (0x0103) – Select user language .................289 Command 260 (0x0104) –...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command 259 (0x0103) – Select user language 11089 Via the command the user lanaguage for the local HMI and the web interface can be set. The language setting always refers to both user interfaces.
Page 290
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command response channel (device >>> fieldbus master) 18011 Offset Word no. reflected user ID reflected command number Command status reserved (→ page 284) command error code current LANG_ID >...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command 261 (0x0105) – Set output control 16673 Using this command, the controller instance for the outputs of the AS-i slaves can be set. >...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command 262 (0x0106) – Set standard PLC operating mode 16674 Using this command, the operating mode of the device-internal standard PLC can be set. >...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command 265 (0x0109) – Set date/time 16677 Using this command, the system time (date and time) of the device can be set. > Command request channel (fieldbus master >>> device) 16694 Offset Word no.
Page 295
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command response channel (device >>> fieldbus master) 16695 Offset Word no. reflected user ID reflected command number Command status reserved (→ page 284) command error code >...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command 266 (0x010A) – Set parameters of the NTP server 16707 Using this command, the IP parameters of the NTP server can be set. >...
Page 297
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP NTP server IP address (IP-V4) of the 2 words Per segment of an IP address: 0 ..255 IP address NTP server 0x00 = 000 0x01 = 001 0x0FF = 255 Example: IP address: 192.168.150.5...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command 267 (0x010B) – Read date / time / NTP settings 16679 Using this command, the current values for time, date and NTP settings can be read. >...
Page 299
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command response channel (device >>> fieldbus master) 16713 Offset Word no. reflected user ID reflected command number Command status reserved (→ page 284) command error code month year (byte 2, MSB) year (byte 1, LSB)
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command 268 (0x010C) – Reboot system 16680 Using the command, the device can be restarted. > Command request channel (fieldbus master >>> device) 7032 Offset Word no.
Page 301
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command response channel (device >>> fieldbus master) 7044 Offset Word no. reflected user ID reflected command number Command status reserved (→ page 284) command error code >...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command 269 (0x010D) – Read fieldbus info 7052 The command reads information via the fieldbus. The command can only be executed using the function block ACnnnn_SysCmd under CODESYS! (→...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command 272 (0x0110) – Display target visualisation 20593 This command enables switching between the menu page of the GUI and the target visualisation as well as enables/disables the use of the key combination [] + [].
Page 304
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > AS-i master commands Overview: AS-i master commands .......................305 Error codes of the AS-i master commands ..................307 Command 01 (0x0001) – Change parameters of an AS-i slave ............310 Command 03 (0x0003) –...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Error codes of the AS-i master commands General error codes ..........................308 Standard CTT2 error codes ........................308 CTT2 error object ..........................309 8836...
Page 308
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > General error codes 5682 Revision: 2014-03-05 Error Code Error Meaning [hex] 0x01 no slave response OR: master is in the offline mode when requesting the command 0x02 no slave with the old address found 0x03...
Page 309
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Error code Description 0x00 No fault 0x01 Invalid index 0x02 Invalid length 0x03 Command not implemented 0x04 Used, the command could not be completed in the specified time 0x05 Command was not acknowledged 0x06...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command 01 (0x0001) – Change parameters of an AS-i slave 8799 Requirement: The addressed AS-i master must be in the protected mode. Command 05 (0x0005) – Change the operating mode of the AS-i master (→...
Page 311
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command response channel (device >>> fieldbus master) 11104 Offset Word no. reflected user ID reflected command number Command status reserved (→ page 284) command error code reserved reserved Input parameters...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command 04 (0x0004) – Change LPS 8806 Requirement: The addressed AS-i master must be in the projection mode. Command 05 (0x0005) – Change the operating mode of the AS-i master (→...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command 05 (0x0005) – Change the operating mode of the AS-i master 8807 > Command request channel (fieldbus master >>> device) 11114 Offset Word no. command number reserved The area is completely ignored.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command 06 (0x0006) – Change AS-i slave address 8808 Requirement: The addressed AS-i master must be in the projection mode. Command 05 (0x0005) – Change the operating mode of the AS-i master (→...
Page 316
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command response channel (device >>> fieldbus master) 11086 Offset Word no. reflected user ID reflected command number Command status reserved (→ page 284) command error code >...
Page 322
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Legend: 0x0000…0xFFFF = 0…65535 user ID 1 word The user ID ensures clear identification of the commmand response data of the command request data sent before. The user can assign any user ID in the command request.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command 21 (0x0015) – Read ID string of an AS-i profile (S-7.4) 8822 > Command request channel (fieldbus master >>> device) 11130 Offset Word no. command number reserved reserved...
Page 326
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command response channel (device >>> fieldbus master) 11131 Offset Word no. reflected user ID reflected command number Command status reserved (→ page 284) command error code Number of bytes received as from word no.
Page 327
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP slave type 1 bit 0 = single slave or A slave 1 = B slave (= addition of 0x20 or 32 to the slave address) >...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command 28 (0x001C) – Deactivate slave reset when changing to the protected mode 8828 When changing from the projection mode to the protected mode, all slaves are normally briefly reset (reset or offline phase).
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command 35 (0x0022) - Write parameter string of an AS-i slave (S-7.4) 8831 > Command request channel (fieldbus master >>> device) 11145 Offset Word no. command number Number of bytes to be transmitted reserved...
Page 335
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command response channel (device >>> fieldbus master) 11143 Offset Word no. reflected user ID reflected command number Command status reserved (→ page 284) command error code Number of bytes received reserved reflected slave address...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Command 81 (0x0051) – Reset error counter 16773 Command sets the following counters to 0: Telegram errors All slave telegram errors Configuration errors ...
Page 370
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Programmers' notes: call up acyclic services 11208 EtherNet/IP controllers use the Message (MSG) command to send data/commands asynchronously to another network participant and receive its response. For detailed information about the Message (MSG) command: →...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > 9.6.6 Configuration mode 12945 To properly set the AC422S for permanent operation in the EtherNet/IP network, type and scope of the data to be transmitted as well as the parameters of the EtherNet/IP interface need to be defined. The following configuration modes are available: ...
Page 372
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Configuration mode: Top-down 12948 In configuration mode 'Top-down', the device-specific parameters and the paramaters of the fieldbus slots are set in the projecting software of the EtherNet/IP controller. The created configuration is then transferred to AC422S (download).
Page 373
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > The [Module Definition] window appears. ► Set the parameters as shown: ► Press [OK] to confirm the input and to close the window. > AC422S appears in the tree structure of the project.
Page 374
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > The [New Module] window appears. ► Set the parameters as shown: ► Press [OK] to confirm the input and to close the window. > AC422S appears in the tree structure of the project.
Page 375
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP ► Click on [_AC422S:C] > The detailed view shows a table with the current values of the configuration assembly instance (device-specific parameters, module configuration) ► For each row (= parameter): enter the desired parameter value in the [Value] column (→ Parameter setting via the configuration assembly object (→...
Page 376
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP ► Select the downloaded file (*.csv) and click [Import] to load it. ► In the tree structure: double-click on [Controller Tags] > The detailed view of the controller tags appears. >...
Page 377
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > Configuration mode: Independent 12949 In configuration mode 'Independent', the device-specific parameters are set via the local display on the Set the configuration mode Set the EtherNet/IP module configuration (→...
Page 378
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP > The [Module Definition] window appears. ► Set the parameters as shown: ► Press [OK] to confirm the input and to close the window. > AC422S appears in the tree structure of the project.
Page 379
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP ► Set the parameters as shown: In the "independent" configuration mode, the value entered for [Assembly Instance] has no relevance since the parameters are set directly on the device (→ Set the device-specific parameters and the module configuration (→...
Page 380
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix Fieldbus EtherNet/IP Optional: import the description of the inputs and outputs into the project ► Download the I/O description file (→ Download the device and I/O description (→...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix OSC messages > OSC messages OSC messages: System ........................382 OSC messages: AS-i 1 / AS-i 2 ......................383 OSC messages: Safety module ......................384 OSC messages: Safety PLCopen function blocks ................401 18959 This section contains information about the messages for events, warnings and faults of the AC422S.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix OSC messages > 9.7.1 OSC messages: System 14284 Message Type Corrective measures ► An internal device error was detected Error Note the message and contact the ifm service center <Fehlernummer>...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix OSC messages > 9.7.3 OSC messages: Safety module 14278 Message Type Corrective measures ► An internal fault in the safety board was detected Error Note the message and contact the ifm service centre. <Fehlernummer1>, <Fehlernummer2>...
Page 385
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix OSC messages > OSC messages: AS-i 1 / AS-i 2 (safety) 6977 Message Type Corrective measures ► ASi_GlobalCom_FailureAscendingAddrSequ_e; Error Note the message and contact the ifm service centre currDev=%s;...
Page 386
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix OSC messages > OSC messages: CODESYS (safety) 6979 Message Type Corrective measures ► CODESYS: invalid FB parameter "ASi_Master": Warning Check setting of the parameter "ASi_Master" currDev=%s; currDiagState=%s; prevDiagState=%s;...
Page 387
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix OSC messages > OSC messages: System (safety) 9137 Message Type Corrective measures ► Overvoltage on the internal supply detected: Warning Check voltage supply of the device and replace, if tmn=%s;...
Page 388
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix OSC messages Message Type Corrective measures ln=%s; p1=%s; p2=%s ► System warning: Warning Note the message and contact the ifm service centre. BIT_ASI_CANT_ADD_OUT_WARN_2; tmn=%s; ln=%s; p1=%s; p2=%s ►...
Page 389
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix OSC messages Message Type Corrective measures tmn=%s; ln=%s; p1=%s; p2=%s ► System error: BIT_BITSPS_INTERNAL_ERR_1; Error Note the message and contact the ifm service centre. tmn=%s; ln=%s; p1=%s; p2=%s ►...
Page 390
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix OSC messages Message Type Corrective measures ln=%s; p1=%s; p2=%s ► System warning: Warning Note the message and contact the ifm service centre. BIT_CHALCOMM_CNCT_DENIED_WARN_1; tmn=%s; ln=%s; p1=%s; p2=%s ►...
Page 391
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix OSC messages Message Type Corrective measures ► System warning: Warning Note the message and contact the ifm service centre. BIT_CHFILE_WRITESIZE_WARN_1; tmn=%s; ln=%s; p1=%s; p2=%s ► System warning: Warning Note the message and contact the ifm service centre.
Page 392
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix OSC messages Message Type Corrective measures ln=%s; p1=%s; p2=%s ► System error: Error Note the message and contact the ifm service centre. BIT_DIAG_TOO_MANY_IRQS_ERR_2; tmn=%s; ln=%s; p1=%s; p2=%s ►...
Page 393
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix OSC messages Message Type Corrective measures ln=%s; p1=%s; p2=%s ► System error: BIT_IHAL_ERROR_ERR_0; Error Note the message and contact the ifm service centre. tmn=%s; ln=%s; p1=%s; p2=%s ►...
Page 394
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix OSC messages Message Type Corrective measures tmn=%s; ln=%s; p1=%s; p2=%s ► System error: BIT_LIO_TMR_READ_ERR_1; Error Note the message and contact the ifm service centre. tmn=%s; ln=%s; p1=%s; p2=%s ►...
Page 395
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix OSC messages Message Type Corrective measures ► System error: BIT_OS_IOC_RD_ERR_0; Error Note the message and contact the ifm service centre. tmn=%s; ln=%s; p1=%s; p2=%s ► System error: BIT_OS_IOC_WR_ERR_0; Error Note the message and contact the ifm service centre.
Page 396
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix OSC messages Message Type Corrective measures ► System error: Error Note the message and contact the ifm service centre. BIT_OS_TASK_SUSPEND_ERR_1; tmn=%s; ln=%s; p1=%s; p2=%s ► System error: Error Note the message and contact the ifm service centre.
Page 397
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix OSC messages Message Type Corrective measures ► System warning: Warning Note the message and contact the ifm service centre. BIT_SAFESTORAGE_READ_WARN_2; tmn=%s; ln=%s; p1=%s; p2=%s ► System warning: Warning Note the message and contact the ifm service centre.
Page 398
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix OSC messages Message Type Corrective measures tmn=%s; ln=%s; p1=%s; p2=%s ► System error: Error Note the message and contact the ifm service centre. BIT_TEMP_SENSOR_VAL_ERR_1; tmn=%s; ln=%s; p1=%s; p2=%s ►...
Page 399
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix OSC messages > OSC messages: Logical devices (safety) 7010 Message Type Corrective measures ERROR (%s): DC=%s, DC-1=%s, AS-i %s, Error Logical device of the safe AS-i slave in locked error state slave %s ERROR (%s): DC=%s, DC-1=%s, terminals %s Error...
Page 400
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix OSC messages > OSC messages: Local inputs/outputs (safety) 20743 Message Type Corrective measures ► Test signal for cross-fault monitoring cannot be Error Check settings of the parameter of the logical detected: currDev=%s;...
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Appendix OSC messages > 9.7.4 OSC messages: Safety PLCopen function blocks 20613 Diagnostic codes of the safety PLCopen function blocks are transferred to the OSC by means of the FB Ctrl_SetDiagInfo.
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Index Command 21 (0x0015) – Read ID string of an AS-i profile (S-7.4) ..325 Index Command 257 (0x0101) – Quick setup AS-i master 1 + 2 ....287 Command 259 (0x0103) –...
Page 403
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Index Control a single standard PLC application .......... 103 Digital output ..................95 Control of the graphical user interface ..........54 Direct link ..................... 174 Control standard PLC applications ............104 Disconnect from web interface ..............
Page 404
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Index structure of the digital input data ..............227 configuration error type 2) ................66 Examples ..................... 220 Mechanical switches ................42 Exception errors ..................31 Menu ...................... 77 Execution control flags ................
Page 405
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Index Overview of slave states ................ 65 Safety architecture ................. 23 Safety classification ................168 Safety functions ..................34 Safety instructions ................10, 39 Page view ....................59 Safety light curtains ................46 Parameter data ..................
Page 406
Original Device Manual Fail-safe SmartPLC with EtherNet/IP interface (AC422S), Firmware 4.0.2 2016-03-02 Index Start screen ................... 78 Navigation ...................... 74 Password protection ..................75 Start screen 'Basic settings' ..............154 Web interface login ................75 Start-up behaviour of the controller ............12 Where is what on the AS-i device? ............