Do not use this router lift for other than its 19. Make your workshop child proof with padlocks, intended use. If used for other purposes, JET master switches or by removing starter keys. disclaims any real or implied warranty and holds itself harmless from any injury that may 20.
Whatever accepted methods are used, always make personal safety a priority. If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our web site: www.jettools.com.
12.0 Warranty and service ..........................25 The specifications in this manual were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations.
Box #4 Stand Assembly 5.0 Setup and assembly Leg tubes Support bars – 2 long, 2 short Lower braces – 2 long, 2 short Read and understand the Miter gauge assembly entire contents this manual before Switch assembly attempting assembly or operation! Failure to Swivel caster assembly comply may cause serious injury! Wheels...
5.4 Stand assembly See Figure 5-6. Mount support bars (2 long, 2 short) to legs (#4). Mount lower braces (2 long, 2 short) to legs. Position JET logo toward front of stand. Install levelers (#19). These can be adjusted for height at any time to make the stand level and accommodate use of the wheels and swivel caster.
5.5 Dust Collection Box See Figure 5-7. Assemble panels as shown, using M4x6 pan head screws (#3). Do not fully tighten screws yet. When all screws are inserted, place box on level surface and push down to settle it evenly. Then tighten all screws. Install dust port (#19) and hose with clamp (#13/20).
5.7 Fence assembly See Figure 5-8. Attach a rail base (#12) to each side of table with socket head cap screws (#18). Hand tighten only. Slide a scale (#15) into each rail (#13). Slide square nuts (#16) into channel of base, and mount rails to bases with hex cap screws (#19) and flat washers (#17).
5.9 Installing router (not provided) The universal clamp collar will secure a router without the need to match hole patterns on its mounting plate. The Router Lift accepts round body routers only, with minimum 3-1/4” diameter to maximum 4-1/4” diameter. Router must be disconnected from power when installing.
3-pole receptacles that accept the tool's plug. Power Switch (part 737006) that accompanies the JRL-912 Router Lift Stand is Repair replace damaged worn cord rated for 120-volt power, and comes with a plug immediately. designed for use on a circuit with a grounded outlet that looks like the one pictured in A, Figure 6-1.
For precise work, verify setting of miter gauge 7.0 Adjustments angle by placing an angle measuring device against miter gauge fence and T-slot. 7.1 Stand mobility narrow table T-slot will accommodate additional routing accessories. Push down pedal on swivel caster (Figure 7-1) to move stand.
by the cutter, both sub-fences are set in a straight line as shown in Figure 8-3. Figure 8-3 When the operation removes the entire edge of the work, for example in jointing or making a full bead, the shaped edge will not be Figure 8-1 supported by the outfeed sub-fence when both The starting pin can be inserted into one of two...
Number of your machine available when you call will allow us to serve you quickly and accurately. Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from JET. Some parts are shown for reference only, and may not be available individually.
11.2.2 Stand Assembly (737004) – Parts List Index No Part No Description Size 2 ....JRL912-202 ....Long Support Bar ..................2 3 ....JRL912-203 ....Short Support Bar ..................2 4 ....JRL912-204 ....Stand Leg ...................... 4 5 ....
11.3.2 Dust Collection Box Assembly (737005) – Parts List Index No Part No Description Size 1N ....JRL912-301N .... Front Panel ....................1 2N ....JRL912-302N .... Right Panel ....................1 3 ....TS-2171012 ....Phillips Pan Hd Machine Screw ....... M4-0.7×6 ..... 34 4 ....
11.5.1 Table Assembly – Exploded View MDF table 11.5.2 Cast Iron Table Assembly (737002) – Parts List Index No Part No Description Size 1 ....JRL912-501 ....Router Table Cast Iron ..........32"x24"......1 2 ....TS-2286201 ....Phillips Flat Head Machine Screw ......M6-1.0x20 ....10 3 ....
JET sells through distributors only. The specifications listed in JET printed materials and on official JET website are given as general information and are not binding. JET reserves the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason whatsoever.