1. Manuals
  2. Brands
  3. Agri-Fab Manuals
  4. Spreader
  5. 45-2142
  6. Owner's manual

Agri-Fab 45-2142 Owner's Manual

100 lb. push broadcast spreader
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
¨
Agri-Fab
OWNERS
MANUAL
Model No.
45-02142
100 LB. PUSH
BROADCAST SPREADER
CAUTION:
Read Rules for
Safe Operation
and Instructions
Carefully
Assembly
Operation
Maintenance
Repair Parts
the fastest way to purchase parts www.speedepart.com
PRINTED IN U.S.A.
FORM NO. 48319 (REV. 11/03)

Advertisement

Table of Contents
loading

Related Manuals for Agri-Fab 45-2142

Summary of Contents for Agri-Fab 45-2142

  • Page 1 ¨ Agri-Fab OWNERS MANUAL Model No. 45-02142 100 LB. PUSH BROADCAST SPREADER CAUTION: Read Rules for Safe Operation and Instructions Carefully Assembly Operation Maintenance Repair Parts the fastest way to purchase parts www.speedepart.com PRINTED IN U.S.A. FORM NO. 48319 (REV. 11/03)

  • Page 2: Rules For Safe Operation

    RULES FOR SAFE OPERATION The following safety precautions are suggested. This Wear eye and hand protection when handling and broadcast spreader is designed, engineered and tested when applying lawn or garden chemicals. to offer reasonably safe and effective service, provided it is operated in strict accordance with these instructions.
  • Page 3 SHOWN FULL SIZE NOT SHOWN FULL SIZE KEY QTY. DESCRIPTION KEY QTY. DESCRIPTION Cotter Pin, 3/32" x 3/4" Long Hex Bolt, 1/4-20 x 1-1/2" Long Flow Control Link Hex Bolt, 1/4-20 x 3/4" Long Spacer Tube Carriage Bolt, 1/4-20 x 3/4" Long Hex Lock Nut, 1/4-20 Thd.

  • Page 4: Tools Required For Assembly

    Place a wheel onto the end of the axle that has a ASSEMBLY INSTRUCTIONS cross hole. The long end of the hub goes to the inside. See figure 3. TOOLS REQUIRED FOR ASSEMBLY Pliers Assemble a 5/32" x 2" cotter pin through the notched Hammer wheel hub and the axle.
  • Page 5 IMPORTANT: Do Not asssemble handle tube to same 13. Assemble the leg stand tube to the handle tube side of crossover tube as shaft support plate. (long) using two 1/4" x 1-1/2" hex bolts. Secure tightly with two 1/4" hex lock nuts. See figure 6. Place the long handle tube onto the crossover tube on the side opposite from the shaft support 14.
  • Page 6 16. Assemble the flow control arm to the flow control 19. Hook the free end of the flow control rod through the mounting bracket using a 1/4" x 3/4" hex bolt, two hole in the slide gate bracket located near the nylon washers and a 1/4"...
  • Page 7 22. Place the adjustable stop into the "ON" end of the 23. Position the flow control mounting bracket (figure slot in the top of the flow control mounting bracket. 13). Secure with the 1/4" x 3/4" carriage bolt, a nylon a.

  • Page 8: Operation

    OPERATION APPLICATION DIAGRAM HOW TO USE YOUR SPREADER SETTING THE FLOW CONTROL 8’ to (Refer to figure 13 on page 7.) 10’ Loosen the nylon wing nut, set the adjustable stop to the desired flow rate setting and retighten the wing nut.

  • Page 9: Maintenance

    MAINTENANCE STORAGE CHECK FOR LOOSE FASTENERS Rinse inside of hopper and exterior of spreader and Before each use make a thorough visual check of dry off before storing. the spreader for any bolts and nuts which may have Store in a clean, dry area. loosened.
  • Page 10 REPAIR PARTS FOR BROADCAST SPREADER MODEL 45-02142...
  • Page 11 REPAIR PARTS LIST FOR BROADCAST SPREADER MODEL 45-02142 REF. PART QTY. DESCRIPTION REF. PART QTY. DESCRIPTION 44624 Hopper 48934 Hairpin Agitator 43882 Rivet, Stainless 43088 Washer, Flat 1/4" Std. 62482 Ass'y, Guide Closure 44468 Sprocket - 6 Tooth 44588 Tube, Frame 44514 Rod, Flow Control 23753...
  • Page 12 REPAIR PARTS Agri-Fab, Inc. 303 West Raymond Sullivan, IL. 61951 217-728-8388 www.agri-fab.com...

Table of Contents