Table of Contents
Advertisement
Available languages
Available languages
desired menu item and confirm with the button
SET The corresponding submenu will be indicated
3) Use the button + or − to make the desired change
and confirm with the button SET The adjusting
options will be explained in the chapters below
4) If an adjustment was changed, "Saving " will
briefly be displayed; if the adjustment remains
unchanged, "Cancel" will briefly appear instead
The menu will be indicated again
5) To exit the menu, select the menu item "Exit"
and confirm with SET
5.5.1 Menu item "Stereo / Mono"
Select the stereo mode with the button + (21) or the
mono mode with the button − (22)
In the stereo mode, each of the two signals will
only be fed to the corresponding earphone The vol-
ume ratio between the two earphones is adjustable
with the balance control (19)
In the mono mode, the two signals will be mixed
to one mono signal and then fed identically to both
earphones The balance control will define the mix-
ing ratio The mono mode is also recommended
when only one stereo channel is received and this
signal is to be fed to both earphones (This is the
case if only one mono signal is available and the
transmitter is set to stereo mode )
5.5.2 Menu item "Hi Freq. Boost"
With this function, the higher frequencies will be
boost ed It can be activated (ON) with the button
+ (21) or deactivated (OFF) with the button − (22)
With the func tion switched on, "HF" (f) will be in-
dicated on the display
5.5.3 Menu item "Limiter"
The integrated limiter is used for limiting the signal
level for the earphones connected to the receiver
When the level exceeds a maximum value depend-
ing on the adjustment of the volume control (18),
the limiter will reduce the level to this value This
will protect your ears from signal peaks suddenly
occurring and will allow a higher monitoring vol-
ume for low and average signal levels It is therefore
recommended to activate (ON) the limiter with the
button + (21) On the display, activation of the lim-
iter will be indicated by "LIM" (g) If, on the other
hand, the dynamic efficiency of the music signal is
to be maintained, deactivate (OFF) the limiter with
the button − (22)
Note: It is the function of the limiter to protect your ears
from temporary signal peaks It will not be able to prevent
any damage to your hearing if you are subjected to very
high volumes for a longer period
18
5.5.4 Menu item "Key lock"
This function will make it more difficult to change
adjustments unintentionally With the key lock func-
tion activated, the main menu cannot be called
Activate (ON) or deactivate (OFF) the function
with the button + (21) or − (22) Activation of the
key lock function will be indicated on the display by
the key symbol (b)
To deactivate, press the button SET (26), then
answer the question "Unlock keypad? [+] Yes / [−]
No" with the button +
5.5.5 Menu item "Contrast"
The contrast of the display can be increased with the
button + (21) or decreased with the button − (22)
The value adjusted will be indicated numerically
(from −3 to 3) and also graphically in the shape of
a sliding control
5.5.6 Menu item "Light time"
The time after which the display illumination is to be
automatically extinguished can be increased with the
button + (21) or decreased with the button − (22)
The value adjusted will be indicated in seconds and
also graphically in the shape of a sliding control The
two end positions mean:
ON
= the illumination is always switched on
OFF
= the illumination is always switched off
Note: The batteries will be saved with shorter illumination
times
5.6 Fastening the receiver
Via the belt clip (25) to be locked into the grooves
on both sides of the receiver, the receiver can be
fastened on your clothes, for example When using
a wireless microphone or transmitter for a musical
instrument at the same time, make sure that the
transmitter and the receiver are not placed side by
side; they might interfere with each other It will be
better to place the two units apart, e g one on the
right side and one on the left side of your body
5.7 Further optional features
of the transmitter
5.7.1 Operating mode MONO / STEREO
Regardless of the receiver, it is also possible to se-
lect the operating mode MONO or STEREO for the
transmitter Set the transmitter to mono when only
one input is used The signal will then be fed to both
sides However, when using the system in the mix /
mono mode, the transmitter must be set to STEREO
while the receiver is set to MONO
The current operating mode will be indicated on
the display at the position (l) as "ST" or "MONO"
Advertisement
Chapters
Table of Contents
