Table of Contents
Advertisement
Quick Links
Dental Computed Radiography Reader
3DISC, FireCR, Quantor and the 3D Cube are trademarks of 3D Imaging & Simulations Corp,
South Korea, and its affiliates. All other trademarks are held by their respective owners and
are used in an editorial fashion with no intention of infringement. The data in this publication
are for illustration purposes only and do not necessarily represent standards or specifications,
which must be met by 3D Imaging & Simulations Corp. All information contained herein is
intended for guidance purposes only, and characteristics of the products and services described
in this publication can be changed at any time without notice. Products and services may not
be available in your local area. Please contact your local sales representative for availability
information. 3D Imaging & Simulations Corp. strives to provide as accurate information as
possible, but shall not be responsible for any typographical error.
© Copyright 2010 3D Imaging & Simulations Corp, all rights reserved, printed, and published
in South Korea by 3D Imaging & Simulations Corp.
User Manual
Doc No. : TM-801-EN
Rev 0.1.2 Nov. 2012
Part No. : CR-FPM-11-001-EN
Advertisement
Table of Contents
Related Manuals for 3Disc FireCR Dental
Summary of Contents for 3Disc FireCR Dental
- Page 1 Rev 0.1.2 Nov. 2012 Part No. : CR-FPM-11-001-EN 3DISC, FireCR, Quantor and the 3D Cube are trademarks of 3D Imaging & Simulations Corp, South Korea, and its affiliates. All other trademarks are held by their respective owners and are used in an editorial fashion with no intention of infringement. The data in this publication are for illustration purposes only and do not necessarily represent standards or specifications, which must be met by 3D Imaging &...
- Page 2 User Manual FireCR Dental TM-801-EN Contact 815, Tamnip-Dong, Yuseong-Gu, Daejeon, Korea Tel : 82-42-931-2100 Fax : 82-42-931-2299 Website : www.3DISCimaging.com E-mail : info@3DISCimaging.com 3DISC Americas 22560 Glenn Dr, Suite 116 Sterling, VA 20164 USA Tel : 1-703-430-6080 E-mail : info@3DISCimaging.com...
- Page 3 User Manual FireCR Dental TM-801-EN The device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
- Page 4 3D Imaging & Simulations Corp. may only be made with prior written permission from 3D Imaging & Simulations Corp. Please read the respective manuals of the connected software, such as acquisition and diagnostic software, before starting to use the FireCR Dental system. The following symbols will be used throughout this manual: ANGER This equipment is indoor use only and all the communication wirings are limited to inside of the building.
- Page 5 User Manual FireCR Dental TM-801-EN General Safety Guidelines All the safety and operating instructions should be read carefully before this device is operated. This device has been designed and tested to meet strict safety requirements applicable to medical equipment, and has been supplied in a safe condition. To ensure personnel and patient safety, the device shall be operated and serviced in compliance with all procedures, warnings and precautions during all phases of operation and service of this device.
- Page 6 User Manual FireCR Dental TM-801-EN Do not look inside of the device. If any of the following conditions occur, unplug the device from the electrical outlet and contact authorized service personnel. The power cord or power adapter is damaged. An object has fallen into the device.
-
Page 7: Table Of Contents
User Manual FireCR Dental TM-801-EN Index of contents Chapter 1. Introduction ..............9 Chapter 2. Unpacking ..............10 2.1. Inspection for Damage ..............10 2.2. Identify the Components ..............10 Chapter 3. Setting Up ..............12 3.1. Positioning ..................12 3.2. - Page 8 User Manual FireCR Dental TM-801-EN Chapter 5. Symbols ............... 28 5.1. Manufacturer’s Declaration ............29 5.1. - Electromagnetic Emission ............29 5.2. Manufacturer’s Declaration - Electromagnetic Immunity ....30 5.3. Guidance and Manufacturer ’s Declaration – Electromagnetic Immunity ..................... 33 5.4.
-
Page 9: Chapter 1. Introduction
Elegant Design & Streamlined Operation The FireCR Dental Reader’s elegant design belies a powerful yet easy-to-use system that gets the job done day in and day out. The reader is DICOM 3.0 compatible with existing systems and uses a full range of low-cost, reusable bitewing and intraoral imaging plates that are easier and faster to position than intraoral digital sensors. -
Page 10: Chapter 2. Unpacking
Chapter 2. Unpacking 2.1. Inspection for Damage FireCR Dental Reader is shipped in a custom designed container to protect the reader from external shock. Before unpacking the reader, inspect the shipping container for damage. In case the container is damaged, notify the shipper immediately. - Page 11 User Manual FireCR Dental TM-801-EN ARNING Use of Power Cord; Type SJT or SVT, min. 18AWG, 3-Conductor, VW-1 125V, min 10A (or 250V, 10A). Max 3.0m long; One end with Hospital Grade Type, NEMA 5-15P for 125V or NEMA 6-15P for 250V. Other end with appliance coupler.
-
Page 12: Chapter 3. Setting Up
User Manual FireCR Dental TM-801-EN Chapter 3. Setting Up ARNING Unsuitable Installation Sites Locations with excessive humidity or dust Locations subject to high temperature Locations subject to shaking or vibration Locations exposed to considerable electrical or magnetic noise, or other forms of electromagnetic energy Locations with poor heat radiation 3.1. -
Page 13: Identify Important Features
User Manual FireCR Dental TM-801-EN ARNING Sliding the reader may result in internal damage or misalignment of the optics. External vibration or shock during scanning may affect image quality. The reader must be placed on rigid, flat and reinforced desk or tabletop. -
Page 14: Touch Display Panel
User Manual FireCR Dental TM-801-EN 3.2.2. Touch Display Panel Screen displays reader’s status and control of the reader can be done by touch screen. Touch display panel Figure 3. Touch Display Panel display Status Remark When the reader is turned on,... - Page 15 User Manual FireCR Dental TM-801-EN Disconnection USB / Ethernet is disconnected. No software Software is not running on PC. Updating Firmware Firmware is being updated. Ready for scan, The reader is ready for scan, but but no IP IP is not placed on the tray.
- Page 16 User Manual FireCR Dental TM-801-EN Scanning Scanning is in progress. Manual Erasing Erasing image from IP manually. Preview Preview of scanned image. Shows information and settings of Setting mode the reader. Scanning Choosing scanning resolution. resolution setting...
- Page 17 User Manual FireCR Dental TM-801-EN Choosing time duration until sleep Auto sleep setting mode. Manual input for network related Network setting settings. Choosing DHCP mode for DHCP setting automatic network settings. IP Address setting Type in IP address manually. Subnet mask Type in subnet mask manually.
-
Page 18: Computer Requirements
User Manual FireCR Dental TM-801-EN Default gateway Type in gateway address Setting manually. 3.3. Computer Requirements 3.3.1. Recommended Requirement Operation System Microsoft Windows 7 (32 bit or 64 bit) Core Duo / Core2 Processor Memory RAM 4GB or more Hard Disk... -
Page 19: Installation Of Acquisition And Diagnostic Software
User Manual FireCR Dental TM-801-EN 3.4. Installation of Acquisition and Diagnostic Software Refer to Acquisition and Diagnostic Software manual. 3.5. Connect the Cable and Power Cord 3.5.1. Connect USB Interface Cable The reader interfaces with computer via USB2.0 cable. 1. Use the USB cable inside the shipping container. -
Page 20: Connect Ethernet Cable
User Manual FireCR Dental TM-801-EN 3.5.2. Connect Ethernet Cable The reader interfaces with computer via Ethernet cable (RJ45 CAT.6 UTP). 1. Connect the cable to the reader’s Ethernet port, located on the rear of the reader. 2. Connect the other end of the cable to the Ethernet port of the Ethernet-hub. -
Page 21: Connect The Power Cord
User Manual FireCR Dental TM-801-EN 3.5.3. Connect the Power Cord 1. Connect the power cord to the reader, located on the rear side. 2. Connect the other end of the cord to a grounded power outlet. Figure 6. Power Connection... -
Page 22: Installation Report
User Manual FireCR Dental TM-801-EN ARNING Socket-outlet shall be installed near the device and shall be easily accessible. Do not place the device where difficult to access to appliance inlet. Do not unplug the power cord or turn the power switch off during scanning. -
Page 23: Chapter 4. Operating
User Manual FireCR Dental TM-801-EN Chapter 4. Operating 4.1. System Specifications 64um Sampling Pixel Pitch 35um 343 x 484 Pixel Matrix (Size 0) 628 x 885 375 x 625 Pixel Matrix (Size 1) 685 x 1143 484 x 640 Pixel Matrix (Size 2) -
Page 24: Operation Conditions
User Manual FireCR Dental TM-801-EN 4.2. Operation Conditions Indoor use only Operating Temperature 15°C ~ 30°C (59°F ~ 86°F) Temperature Gradient 0.5°C / Min Relative Humidity 15% ~ 95% (non-condensing) Storage Temperature - 10°C ~ 50°C (14°F ~ 122°F) Storage Humidity... -
Page 25: Operating Instructions
User Manual FireCR Dental TM-801-EN 4.3. Operating Instructions 4.3.1. Turn on the Reader Turn on the reader. Power switch is on the rear side of the reader. ANGER This device uses laser. Avoid looking inside of the reader. 4.3.2. Turn on the Computer Turn on the computer. -
Page 26: Getting A Scanned Image
User Manual FireCR Dental TM-801-EN In order to scan or erase the IP, locate the IP on the tray correctly and push the tray into the reader fully until interlock holds the tray. ARNING Locate the IP in correct position. -
Page 27: Chapter 5. Symbols
User Manual FireCR Dental TM-801-EN Chapter 5. Symbols Symbol Description .Manufacturer Date of Manufacture Equipment Power ON Equipment Power OFF Warning, Consult Accompany Documents General mandatory action manual prohibition General indication User Manual Reference Directive on Waste Electrical and Electronic Equipment... - Page 28 5.1. Manufacturer’s Declaration- Electromagnetic Emission The FireCR Dental system is intended for use in the electromagnetic environment specified below. The customer or the user of FireCR Dental system should assure that it is used in such an environment Emission test...
-
Page 29: Manufacturer's Declaration - Electromagnetic Immunity
Manufacturer’s Declaration - Electromagnetic Immunity The FireCR Dental system is intended for use in the electromagnetic environment specified below. The customer or the user of FireCR Dental system should assure that it is used in such an environment IEC 60601... - Page 30 User Manual FireCR Dental TM-801-EN Conducted RF 3 Vrms 3 Vrms Portable and mobile RF IEC 61000-4-6 150 kHz to 80 MHz 150 kHz to 80 MHz communications equipment should be used no closer to Dental any part of the FireCR...
-
Page 31: Immunity
The FireCR Dental system is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The user of the FireCR Dental system can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the FireCR Dental system as recommended below, according to the maximum output power of the communications equipment. -
Page 32: Guidance And Manufacturer 'S Declaration – Electromagnetic Immunity
5.3. Guidance and Manufacturer ’s Declaration – Electromagnetic Immunity The FireCR Dental system is intended for use in the electromagnetic environment specified below. The customer or the user of FireCR Dental system should assure that it is used in such an environment IEC 60601... -
Page 33: Laser Safety Statement
User Manual FireCR Dental TM-801-EN 5.4. Laser Safety Statement The Computed Radiography Reader is Certified in the U.S. to Conform to the Requirements of DHHS 21 CFR, chapter 1 Subchapter J for Class I(1) Laser Products, and Elsewhere is Certified as a Class I(1) Laser Product Conforming to the Requirements of IEC 60825-1 : 2007. -
Page 34: Chapter 6. Warranty And Repair Service
User Manual FireCR Dental TM-801-EN Chapter 6. Warranty and Repair Service 6.1. Standard Warranty 3D Imaging & Simulations Corp. warrants its non-consumable hardware products to be free from defects in materials and workmanship. The warranty covers the cost of parts and labor to repair the product. -
Page 35: Shipping
If user needs to ship the FireCR Dental Reader to another location, or back to the factory, and user does not have a means to adequately package it, user can order additional shipping container. -
Page 36: Chapter 7. Technical Assistance
User Manual FireCR Dental TM-801-EN Chapter 7. Technical Assistance If user has any questions about installing or using the device, contact your 3D Imaging & Simulations Corp representative or your local dealer. 3D Imaging & Simulations Corp. 815, Tamnip-Dong, Yuseong-Gu, Daejeon, Korea... - Page 37 Fax : +82-42-931-2299 E-mail : support@3DISCimaging.com Date of Installation : Customer Information Hospital / Institute Name Address E-mail Installer Information Company Name Address E-mail System Information Model FireCR Dental Reader System S/N Installer’s Signature: Date: Customer’s Signature: Date:...
Need help?
Do you have a question about the FireCR Dental and is the answer not in the manual?
Questions and answers