Burkert 2100 Quick Start Manual
2/2- and 2/3-way angle seat valve
Hide thumbs
Also See for 2100:
- Operating instructions manual (118 pages) ,
- Quick start manual (64 pages) ,
- Replacement instructions manual (12 pages)
Related Manuals for Burkert 2100
Summary of Contents for Burkert 2100
- Page 1 Type 2100 2/2- and 2/3-way angle seat valve 2/2- und 2/3-Wege-Schrägsitzventil Vanne à siège incliné 2/2 et 2/3 voies Quickstart English Deutsch Français...
- Page 2 We reserve the right to make technical changes without notice. Technische Änderungen vorbehalten. Sous réserve de modifications techniques. © 2013-2017 Bürkert Werke GmbH & Co. KG Operating Instructions 1709/04_EU-ML_00810247 / Original DE...
-
Page 3: Table Of Contents
10 removal ................16 www.burkert.com 11 packaGinG, transport, storaGe ......16 Definition of term / abbreviation The term “device” used in these instructions always stands for the angle seat valve Type 2100. The abbreviation “Ex” stands for potentially explosive area. english... -
Page 4: Symbols
2100 is designed for the controlled ▶ Failure to observe the warning may result in a fatal or serious injury. flow of liquid and gaseous media. -
Page 5: Basic Safety Instructions
Type 2100 Basic safety instructions basic safeTy insTrucTions Warning! These safety instructions do not make allowance for any risk of burns. • contingencies and events which may arise during the installation, The surface of the device may become hot during long-term operation and maintenance of the devices. -
Page 6: General Information
Information on the Internet actuator. ▶ Do not put any loads on the valve (e.g. by placing objects on The operating instructions and data sheets for Type 2100 can be it or standing on it). found on the Internet at: www.burkert.com... -
Page 7: Technical Data
Type food contact tives, can be found on the EU Type Examination Certificate and / or the EU Declaration of Conformity. 2100 A 32M PTFE VA Pilot 4,8-10bar According to Pressure Equipment Directive the following operating Tmed -10°C - +185°C... - Page 8 Type 2100 Technical data Minimum pilot pressure: flow direction below the seat Actuator Actuator Medium temperature Ambient (medium flow against the closing direction of the valve) size material (for PTFE seal) temperature Required minimum pilot pressure P with control function A: ø...
-
Page 9: Installation
Type 2100 Installation General technical data insTallaTion media Danger! Control medium Neutral gases, air risk of injury from high pressure. Flow media Water, alcohol, fuel, hydraulic liquids, ▶ Before loosening the lines and valves, turn off the pressure saline solutions, lye, organic solvents and vent the lines. - Page 10 Type 2100 Installation Remove the actuator from the valve Caution! body (welded body) risk of injury due to a heavy device. → Clamp the valve body in a holding device. A heavy device can fall down during transport or during instal- lation and cause injuries.
- Page 11 Type 2100 Installation Installation of the valve body Install actuator (welded body) Warning! risk of injury from improper installation. Seal ▶ Installation may only be performed by qualified and trained personnel. ▶ For installation use an open-end wrench. ▶ Observe the tightening torque.
- Page 12 Type 2100 Installation Rotating the actuator → Screw actuator into the valve body. Observe tightening torque into “Tab. 5”. The position of the connections can be aligned steplessly by rotating the actuator through 360°. Air discharge con- nection CFA, CFB...
- Page 13 Type 2100 Installation 7.7.1 Connection of the control medium Open-end wrench If the position of the pilot air ports for installation of the hoses is unfavorable, these can be aligned steplessly by rotating the actuator through 360°. The procedure is described in the chapter entitled “7.3.4 Rotating the actuator”.
- Page 14 Type 2100 Installation Start-up After installing the device, run the teach function. This function presets the control parameters. Pilot air port for control function A - center position Description – see operating instructions for the control. Pilot air port for control function A - open Fig.
-
Page 15: Start-Up
Type 2100 Start-up STaRT-uP 8.2.1 Flow direction above the seat Control function A, CFA: closes by spring force against the medium Warning! flow. Control function B, CFB: closes with the control pressure against the medium flow. The medium pressure supports the risk of injury from improper operation. -
Page 16: Removal
Type 2100 Removal visual inspection removal Perform regular visual inspections according to the application Danger! conditions: → Check media connections for leaks. risk of injury from discharge of medium and pressure. → Check release bore on the tube for leaks. - Page 18 www.burkert.com...
Need help?
Do you have a question about the 2100 and is the answer not in the manual?
Questions and answers