Table of Contents
Advertisement
3
Load a scene file.
To load a scene file stored in the camcorder
Turn the MENU knob to move the
desired file number, and press the MENU knob.
The s which is displayed on the left of the file number
changes to x.
The camcorder is set up according to the loaded scene
file.
F04 SCENE FILE
s1
x2
s3
s4
s5
sSTANDARD
SCENE RECALL
SCENE STORE
F.ID: SCENE21
To cancel the selected scene file
b
Move the
mark to x, and press the MENU knob. x
changes to s.
The camcorder returns to the settings before selecting
this scene file.
To load a scene file saved in the "Memory Stick"
Proceed as follows:
1 Turn the MENU knob to move the
"SCENE RECALL," and press the MENU knob.
The P00 SCENE RECALL page appears.
?P00 SCENE RECALL
DISPLAY MODE
MEM<1>:STANDARD
MEM<2>:STANDARD
MEM<3>:STANDARD
MEM<4>:STANDARD
MEM<5>:NO FILE
2 Turn the MENU knob until the page which
contains the desired file number appears, then press
the MENU knob.
3 Turn the MENU knob to move the
desired file number, and press the MENU knob.
The message "RECALL OK? YES bNO" appears.
P01 SCENE RECALL
RECALL OK?
DISPLAY MODE
001.SCENE1
002.SCENE2
003.NO FILE
004.SCENE4
005.SCENE5
***.5FILE LOAD
4
To carry out the recall, move the
press the MENU knob.
104
Saving and Loading Scene Files
b
mark to the
TOP
:SCENE 25
:SCENE 26
:SCENE 27
:SCENE 28
:NO FILE
:
EXEC
:
EXEC
b
mark to
ESC
:
F.ID
b
mark to the
ESC
YES NO
:
ALL
MEM1-5
b
mark to "YES" and
To cancel, press the MENU knob leaving the
pointing to "NO."
When the loading is completed, the message
"COMPLETE" appears. The camcorder is set up
according to the loaded scene file.
If no file is present with a particular file number, this is
shown as "NO FILE."
5
To end the menu operation, set the MENU ON/OFF
switch to OFF.
Loading scene files from a "Memory Stick"
into the camcorder memory
You can load up to five scene files stored in the "Memory
Stick" into the camcorder memory in a single operation.
1
After displaying the SCENE FILE page (page 101),
turn the MENU knob to move the
RECALL," and press the MENU knob.
A SCENE RECALL page appears.
2
Turn the MENU knob until the SCENE RECALL page
which contains the desired scene files appears, then
press the MENU knob.
3
Turn the MENU knob to move the
b
LOAD
MEM 1-5," and press the MENU knob.
The message "RECALL OK? YES bNO" appears.
P01 SCENE RECALL
RECALL OK?
DISPLAY MODE
001.SCENE1
002.SCENE2
003.NO FILE
004.SCENE4
005.SCENE5
***.5FILE LOAD
4
To carry out the recall, move the
press the MENU knob.
To cancel, press the MENU knob leaving the
pointing to "NO."
When loading is complete, the message
"COMPLETE" appears and the ACCESS indicator
goes off.
5
To end the menu operation, set the MENU ON/OFF
switch to OFF or close the cover of the menu operating
section.
Notes
• The scene files loaded from the "Memory Stick"
overwrite data saved in the camcorder memory.
b
mark
b
mark to "SCENE
b
mark to "5FILE
ESC
YES NO
:
ALL
MEM1-5
b
mark to "YES" and
b
mark
Advertisement
Table of Contents
