Related Manuals for Zephyr Siena Pro ZSP-E36BS
Summary of Contents for Zephyr Siena Pro ZSP-E36BS
- Page 1 Siena Pro ZSP-E36BS ZSP-E42BS ZSP-E48BS Model number: Serial Number: APR19.0301 © Zephyr Ventilation LLC.
- Page 2 www.zephyronline.com...
-
Page 3: Table Of Contents
SAFETY NOTICE ..............LIST OF MATERIALS ............INSTALLATION Ducting Calculation Sheet ........Mounting Height & Clearance ........ Ducting Options ......................Mounting the Range Hood ........FEATURES & CONTROLS ICON Touch Controls ..........MAINTENANCE Cleaning, Filter Care, Part List ......LED Light Strip ............. -
Page 4: Safety Notice
www.zephyronline.com READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a. - Page 5 WARNING TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. CAUTION attics, crawl spaces or garages. OPERATION and loose clothing. The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation, maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to negligence and the warranty of the unit automatically expires due to improper maintenance.
-
Page 6: List Of Materials
www.zephyronline.com MODELS: ZSP-E36BS, ZSP-E42BS, ZSP-E48BS PARTS SUPPLIED 1 - Hood with internal blower 2 - Baffle filters (3 for ZSP-E48BS) 1 - Duct cover assembly (top and bottom) 1 - Duct cover wall bracket 1 - 9W Brite Strip™ LED (2 for ZSP-E48BS) 1 - 10”... -
Page 7: Ducting Calculation Sheet
Equivalent number Equivalent number Duct pieces Duct pieces T otal length x used length x used T otal 3- 1/ 4” x 10” 1 Ft. 3- 1/ 4” x 10” 5 Ft. Rect., Rect. to straight 6” round transition 6”, 7”, 8”, 10” 1 Ft. -
Page 8: Installation
www.zephyronline.com ALWAYS, when possible, reduce the number of transitions and turns. If a long duct run is required, increase duct size from 10” to 12”. If turns or transitions are required: Install as far away from opening and as far apart, between 2, as possible. -
Page 9: Ducting Options
WARNING FIRE HAZARD All exhaust must be ducted to the outside, unless using the recirculating option. Some Ducting Options Roof Pitch w/ Flashing & Cap side wall cap w/ gravity damper Soffit or crawl space side wall cap w/ gravity damper... - Page 10 www.zephyronline.com 11/16” ”, 41 ”, 47 ” FRONT 3/16” STANDARD min. ducted - 27 1/2” min. recirc. - N/A max. - 42” Z1C-00SP min. ducted - 45” min. recirc. - N/A max. - 78” 15/16” SIDE 3/4” AC In...
-
Page 11: Mounting The Range Hood
CAUTION: At least two installers are required due to the weight and size of the hood. Duct Cover Bracket 14-15/16" screws all the way. Note: wood blocking may need to 12-1/8" be added behind the drywall if no studs are present. 1-3/8"... -
Page 12: Icon Touch Controls
www.zephyronline.com Power / Delay Off Adjust 5 Speed Levels Lights On/Dim/Off Display (speed level, delay off, filter clean/change) 1 POWER / DELAY OFF BUTTON Power Button Function Button will turn power on and off for entire hood (fan and lights). - Hood will remember the last speed and light level it was turned off at. -
Page 13: Cleaning, Filter Care, Part List
SURFACE MAINTENANCE: Clean the hood surface periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent, or steel wool/scouring pads which will scratch and damage surface. For heavier soil use liquid degreaser. After cleaning it is recommended that you use non-abrasive stainless steel polish/cleaners, to polish and Do not use any product containing chlorine bleach. -
Page 14: Led Light Strip
www.zephyronline.com LED LIGHT STRIPS To replace LED light strip 2. Remove light panel by two screws. 4. Push in the two side clips on the ends of the LED strip. 5. Push LED light strip through the light panel opening. Push the clip... -
Page 15: Act Conversion
Some local codes limit the maximum amount of CFM a range hood can move. ACT allows you to control the codes for CFM restrictions. By default the maximum blower CFM is set to 1200. CAUTION: Hood must be disconnected from main power prior to performing the conversion instructions listed below. -
Page 16: Fan Curve Diagrams
www.zephyronline.com Blower Fan Curve Model: ZSP AC Input: 120V, 60Hz Outlet Diameter: 10in 2.80 2.70 2.60 2.50 2.40 2.30 2.20 2.10 2.00 1.90 1.80 1.70 1.60 1.50 1.40 1.30 1.20 1.10 1.00 0.90 0.80 0.70 0.60 0.50 0.40 0.30 0.20 0.10 0.00 1000 1050 1100 1150 1200 1250 1300... -
Page 18: Wiring Diagram
www.zephyronline.com ZSP-E36BS VOLTS MAX AMPS ZSP-E42BS CIRCUIT DIAGRAM WHIT E WHIT E G R AY G R AY B R OWN B R OWN B LUE B LUE Y E LLOW Y E LLOW R E D R E D G R E E N G R E E N B ODY... -
Page 19: Troubleshooting
TROUBLESHOOTING PROCEDURES FOR SIENA PRO Issue Cause What to do After installation, 1. The power source is not turned ON. the unit doesn’t power is ON. is not connecting properly. connected properly. 3. The wires on the control board are loose. connected properly. -
Page 20: Warranty
This warranty is not extended or restarted upon warranty repair or replacements. www.zephyronline.com. Zephyr Ventilation Service Department, 2277 Harbor Bay Parkway, Alameda, CA 94502 1-888-880-8368... -
Page 21: Product Registration
IT’S IMPORTANT Prompt registration helps in more ways than one. Ensures warranty coverage should you need service. Ownership verification for insurance purposes. Notification of product changes or recalls. Zephyr Ventilation | 2277 Harbor Bay Pkwy. | Alameda, CA 94502 | 1.888.880.8368...
Need help?
Do you have a question about the Siena Pro ZSP-E36BS and is the answer not in the manual?
Questions and answers