Summary of Contents for Farmi Forest Corporation JL 601
Page 1
03121060 B // En // 141001 MRu JL 601 OPERATING, MAINTENANCE AND SPARE PARTS MANUAL www.normet.fi SKIDDING WINCH JL 601 From machine 03121000 IT IS VERY IMPORTANT TO READ THIS INSTRUCTION MANUAL THOROUGHLY BEFORE USING THE MACHINE Page Normet Corporation...
Page 2
03121060 B // En // 141001 MRu JL 601 OPERATING, MAINTENANCE AND SPARE PARTS MANUAL WARNING SYMBOLS IN THE MANUAL An immediate danger which may cause serious injuries or even death. DANGER! Risk of injuries. WARNING! A general risk or danger, which may cause material damage due to false operation.
Page 3
B // En // 141001 MRu JL 601 OPERATION, MAINTENANCE AND SPARE PARTS MANUAL GUARANTEE OF MACHINE CONFORMANCE TO EU REQUIREMENTS Normet Corporation Ahmolantie 6, FIN- -74510 PELTOSALMI, Finland Informs that the machine, launched on to the market, Farmi winch...
B // En // 141001 MRu JL 601 SAFETY INSTRUCTIONS Do not use the winch, before you have read and understood the manual! The owner is responsible for the guidance of all persons, who have to deal with the device.
Page 6
B // En // 141001 MRu JL 601 SAFETY INSTRUCTIONS D D D D Do not wear loose clothing, loose sleeves or scarves around moving parts of machinery. Long hair must be kept under helmet or cap! D D D D Make sure that others are not in danger when you use the winch.
B // En // 141001 MRu JL 601 STICKERS AND SIGNS Fig. 3. Falling danger! Do not work in an oblique position. Fig. 4. Crushing danger! Do not use the winch for the lifting. Fig. 5. Watch out for a breaking cable! Always use the protective screen.
B // En // 141001 MRu JL 601 STICKERS AND SIGNS Fig. 9. Falling danger! Do not winch at sideways angles exceeding 30 degrees. Fig. 10. Crushing danger! Do not stand in front of the winch when working. Stand on the side at a distance of at least 6ft from the winch.
B // En // 141001MRu JL 601 MOUNTING INSTRUCTIONS 4.3. SHORTEN THE DRIVE SHAFT 4. MOUNTING INSTRUCTIONS Both PTO halves must be shortened by equal amounts. 4.1. MOUNTING TO THE PTO is optional equipment. 3- -POINT HITCH Note! The winch can be mounted to the 3---point linkage of any tractor.
B // En // 141001MRu JL 601 MOUNTING INSTRUCTIONS 4.4. FASTENING THE CABLE TO THE 5. PRE- -OPERATION CHECKS DRUM 1. Tape the cable end to prevent loosening of CABLE the core wires. Check that: 2. Pass the cable through the hole in cable guard, over the upper snatch block and D The cable is faultless (breakage risk).
B // En // 141001 MRu JL 601 OPERATION INSTRUCTIONS 6. CONTROLS 7. OPERATION Get acquainted with the 7.1. SAFETY PRECAUTIONS controllers of the winch before the use, tests the stopping Read the operation functions of the winch and the...
B // En // 141001 MRu JL 601 OPERATION INSTRUCTIONS D The falling danger of the tractor can be 7.2. PRE- -OPERATION CHECKS reduced by winching through the lower snatchblock. MOUNTING AND USE OF THE LOWER SNATCHBLOCK D Usually the logs are winched in through the upper pulley of the winch.
B // En // 141001 MRu JL 601 OPERATION INSTRUCTIONS 7.3. WINCHING Avoid extra large loads. The winding speed depends on the number of revolutions of the tractor. Do not wind too fast. Before using the winch, you have to pull the cable 4.
B // En // 141001 MRu JL 601 OPERATION INSTRUCTIONS IF YOU GET STUCK WITH THE TRACTOR: 1. Drop the load. Drive the tractor to firm ground. Winch in the load. 2. If you cannot move the tractor, release the load and winch the tractor out.
B // En // 141001MRu JL 601 MAINTENANCE, LUBRICATION AND ADJUSTMENT INSTRUCTIONS 8. SAFETY 10. SERVICE Disengage the P.T.O and turn 10.1. CLUTCH ADJUSTMENT the tractor off before you service the winch, remove the 1. Loosen the nuts A and B at both ends of keys so the tractor cannot be the drum axle.
B // En // 141001MRu JL 601 MAINTENANCE, LUBRICATION AND ADJUSTMENT INSTRUCTIONS 10.2. ADJUSTING THE ROLLER 10.4. REMOVING THE WINCH CHAIN TIGHTNESS MECHANISM Roller chains tightness adjustment is carried The whole winch mechanism can be removed out by moving the chain tightener. See fig. 33.
11. ORDER SPARE PARTS When ordering spare parts, please refer to your machines type code on the name plate and to the spare parts lists order number, description and quantity desired. JL 601, 54511340, Bearing, 1 pc. Page Normet Corporation...
B // En // 141001MRu JL 601 MAINTENANCE, LUBRICATION AND ADJUSTMENT INSTRUCTIONS 12. TROUBLE SHOOTING CONDITION POSSIBLE CAUSE REMEDY Hard to pull the cable out Drum brake is too tight Loosen the drum brake. See instructionsfrom item 10.3 ”Adjusting the drum brake”.