MIMAKI UCJV300 Manual

MIMAKI UCJV300 Manual

Id cut
Hide thumbs Also See for UCJV300:

Advertisement

Quick Links

UCJV300/150 ID Cut Guide
Congratulations on your purchase of an inkjet printer of MIMAKI (print & cut type).UCJV300/150 This " ID Cut
Guide", describes the method for ID cut by using UCJV300/150 and the supplied software. Precautions and pre-
defined settings are also described.

Note

• It is strictly prohibited to write or copy a part or whole of this document without our approval.
• This document has been carefully prepared for your easy understanding, however, please do not hesitate to
contact a distributor in your district or our office if you have any inquiry.
• Description contained in this document are subject to change without notice for improvement.
• Due to improvement or change of software, the description of this document could be partially different in
specification, for which your understanding is requested.
• With the exception of what is provided for in the warranty provisions of MIMAKI ENGINEERING CO., LTD., we
do not assume any liability against the damages (including but not limited to the loss of profit, indirect damage,
special damage or other monetary damages) arisen out of the use or failure to use of this product. The same
shall also apply to the case even if MIMAKI ENGINEERING CO., LTD. had been notified of the possibility of
arising damages in advance. As an example, we shall not be liable for any loss of the media made using this
product or indirect damages caused by the product made using this media.
• You can also download the latest operation manual from our website.
FineCut, RasterLink, RasterLink6Plus and CuttingLink are registered trademarks of MIMAKI ENGINEERING CO.,
LTD.
Adobe Illustrator is a trademark of Adobe Systems Incorporated.
CorelDRAW is a trademark of Corel Corporation.
Microsoft and Windows are registered trademarks of Microsoft Corporation of the U.S.A.
Apple and Macintosh are registered trademarks of Apple Inc. of the U.S.A. and each country.
All brand names and product names are trademarks or registered trademarks of their respective companies.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the UCJV300 and is the answer not in the manual?

Questions and answers

Summary of Contents for MIMAKI UCJV300

  • Page 1: Note

    UCJV300/150 ID Cut Guide Congratulations on your purchase of an inkjet printer of MIMAKI (print & cut type).UCJV300/150 This " ID Cut Guide", describes the method for ID cut by using UCJV300/150 and the supplied software. Precautions and pre- defined settings are also described.
  • Page 2: Table Of Contents

    TABLE OF CONTENTS Note ......................1 What is ID cut? ..................3 ID Cut Procedure ..................4 Preparation ........................... 5 Set up PC........................... 5 Printing, and ID Cutting ......................... 8 Set the media..........................8 Print data............................ 9 ID cut ............................
  • Page 3: What Is Id Cut

    (Auto) Adjusting the image quality and colors, and so on. Cut data management. ID Data Cut Data ID Data Print (Auto) Printed register marks detection. Automatically cut • System configuration 1-3.Regitration of UCJV300/150 2-4.Regitration of CuttingLink UCJV300/150 - 3 -...
  • Page 4: Id Cut Procedure

    ID Cut Procedure 1. Software / Driver List (P.5) 1. Connect PC and UCJV300/150 with USB. (P.5) 2. Install CuttingLink. (P.5) 3. Register UCJV300/150 with CuttingLink. (P.5) 4. Register CuttingLink with RasterLink6Plus. (P.6) 2. Set the media. (P.8) 1. Set the media onto UCJV300/150. (P.8) 2.
  • Page 5: Preparation

    You need to prepare UCJV300/150 and the software/Driver before printing or ID cut. If preparations have already been completed, go to"Printing, and ID Cutting" (P.8). • Software / Driver List The following software applications are required for ID cut. All software applications are provided by MIMAKI ENGINEERING CO., LTD. Software/Driver...
  • Page 6 (3) From the [Tool] menu, select [Cutting Device Manager]. (4) Select UCJV300/150 in [Available Devices]. (5) Enter [Name], and then click [Add]. • UCJV300/150 is added to the list. (6) Click [Close]. • CuttingLink is started automatically when PC starts.
  • Page 7 (3) Click the [Communication] tab on the [Option] screen. (4) [Setting of ID Cut: Click [Setup] in [Connection destination]. • The [Connection destination setting] screen is displayed. (5) On the [Connection destination setting] screen, select this my computer, and then click [OK]. •...
  • Page 8: Printing, And Id Cutting

    P.5 "Preparation" and then print and cut. Set the media. For detail, refer to the UCJV300/150 Operation Manual. I you cut the media rotated by 90, 180, or 270 degrees, set the media margins to the following values at rotated conditions.
  • Page 9: Print Data

    Print data. 1. Start RasterLink6Plus. 2. Set the manual CD to your computer. 3. From the [File] menu, select [Open]. • The [Select file name to print] screen is displayed. 4. Read the Sample file. (1) Select the following files on the [Select file name to print] screen, and click [Open].
  • Page 10 7. Click the Execution icon in the function icon list on the right side of the screen. 8. Select [RIP & Print] or [Immediate Print]. 9. Click [Start]. 10. Data with ID will be printed. - 10 -...
  • Page 11: Id Cut

    ID cut 1. Detect the register mark (1) Press the [SEL] key twice in LOCAL mode. (2) Press [][] key to select [MARK DETECTION], and press the [ENTER] key. • This switches to the mark detection mode. (3) Press the [][][][]keys to move the luminous point of the LED pointer to the center of the reg- ister mark.
  • Page 12: How To Handle The Following Cases

    How to handle the following cases. Troubleshooting The [ID Cut] check box is disabled in RasterLink6Plus. Is the data size of the job 70 mm or more? Set the data size to 70 mm or more. Have you selected [Type 1], [Type 2] for Select [Type 1] or [Type 2] for register mark the register mark shape? shape.
  • Page 13 Even if register marks are detected with UCJV300/ 150, ID cut is not performed. Is PC and UCJV300/150 connected via Connect with USB or Ethernet. USB or Ethernet? Is UCJV300/150 properly registered in CuttingLink - Server? Confirm the following contents on the [Cutting Device Manager] tab of Cuttin- gLink - Server.
  • Page 14: Changed Cuttinglink - Server

    4. Copy the data backed up on the PC before migration to the folders below. • C:\MimakiTools\CuttingLink\DT 5. Start CuttingLink. 6. Register the UCJV300/150. P.5 "Register UCJV300/150 with CuttingLink."(3) to (6)) 3. Register CuttingLink - Server PC on RasterLink6Plus. P.6 "Register CuttingLink with RasterLink6Plus." - 14 -...
  • Page 15: When To Use Cuttinglink - Client

    Register Register How to set CuttingLink - Client 1. Install CuttingLink on the PC connecting 1st to 5th UCJV300/150, and set it to Cuttin- gLink - Server.( P.5 "Install CuttingLink." or later) 2. Install CuttingLink on the PC connecting the sixth UCJV300/150 and set it to Cuttin- gLink - Client.
  • Page 16: Data In The Same Place Is Cut Twice

    (3) In the [Connection destination settings] list, select the CuttingLink - Server to connect and click [OK]. • Make sure that CuttingLink - Server is running with Cuttin- gLink - Server PC. • If the [Connection destination settings] screen does not appear, select the [Connection destination settings] on the [Tool] menu.
  • Page 17: When You Want To Id Cut Multiple Types Of Data

    When you want to ID cut multiple types of data If you print multiple register marks and perform ID Cut, set the same shape and size for all the register marks. If any of the register marks has a different size or shape, the ID Cut is canceled. Because the shape of the register mark is different, an error occurs and the ID Cut is canceled.
  • Page 18 • Offset: Data and margin of register mark Offset Offset Offset Offset 5. Output data with RasterLink6Plus( P.9 "Print data.") • Data with ID will be printed. 6. Create another data and repeat Step1 to Step5. 7. Set the printed media on UCJV300/150. - 18 -...
  • Page 19 8. Set the register mark detection area on the operation panel of UCJV300/150. (1) Press the [MENU]([FUNC1] key) in LOCAL mode. (2) Press [][] key to select [CUTTING], and press the [ENTER] key. (3) Select [MARK DETECTION], and press the [ENTER] key.
  • Page 20 9. Set the printed media. The register mark is detected in the feed (media feed) direction. Set the media margins to the following values. • Front end: 110 mm or more • Left and right ends: 15 mm or more •...
  • Page 21 MEMO:...
  • Page 22 D203243-12-09032018 © 2017 MIMAKI ENGINEERING CO., LTD. All rights reserved.

This manual is also suitable for:

Ucjv150

Table of Contents