Grass Catcher Operation; Emptying Grass Catcher - Snapper 0-50576 Operator's Manual

INTRODUCTION
Follow operation and maintenance instructions in the
Operator's Manual provided with the Snapper CZT/HZT.
GRASS CATCHER OPERATION
1. Select desired cutting height. Choose a setting that will
not attempt to cut off too much at once, overloading the
machine.
2. After starting engine and allowing a brief warm up peri-
od, move engine speed control to highest setting.
3. Drive machine to cutting area. Engage blades.
4. Select a slow forward ground speed until familiar with
conditions. Do not select a speed that is too fast, caus-
ing the machine to become overloaded.
5. The weight of the grass catcher and contents will affect
the stability and handling of the machine. Avoid sudden
starts and sharp turns. Reduce speed on slopes, and
DO NOT operate machine on slopes exceeding 10
degrees (18% grade). Operate machine up and down
slopes. DO NOT operate machine across the face of
slopes. Turn blades off when traveling up slope.
6. Empty grass catcher bags often to minimize effect on
stability and handling. Over filling the catcher bags will
reduce performance and cause clogging of the hose,
blower and deck.
7. Do not operate the machine with the Grass Catcher
cover open. The entire Grass Catcher must be installed,
the cover closed and latched properly before operating.
EMPTYING GRASS CATCHER
1. Empty Grass Catcher bags often to avoid overfilling.
Overfilling reduces performance and causes clogging of
hose, blower and deck.
2. Turn blades off. Drive machine to location the clippings
are to be dumped. DO NOT operate blades in reverse.
If you must back machine to dump clippings in desired
location, LOOK and SEE behind and down for children,
pets and hazards before and while backing.
3. Stop motion of machine by returning Motion Control(s)
to Neutral (N). Set Park Brake. Stop engine.
4. Unlatch cover and lift. Remove bags and dump debris
in desired location.
5. After dumping, to maintain peak performance, check
the catcher screen located on the inside of the Cover
Assembly to make sure it is clean and free of any build
up. Clean as required with brush or broom.
6. Close catcher cover and latch.
7. Re-start engine and drive machine to cutting area. Set
engine speed to highest setting, engage blades and
resume operation.
WARNING
DO NOT attempt to remove any clogs from deck, blow-
er, or hose with engine or blade running. STOP engine.
STOP blades. Set brake. Remove key. Make sure
blades and all rotating components have come to a
complete stop before removing any catcher or unclog-
ging any catcher component.
IF THE GRASS CATCHER BECOMES CLOGGED
The grass catcher may become plugged if the conditions
are too severe, the catcher is overfilled, or the machine is
used improperly. If plugging does occur, attempt the follow-
ing:
1. Engine speed too slow - set engine speed control to
"FAST" position.
2. Empty catcher bags more often.
3. Clean screen on cover assembly.
4. Ground speed too fast - cut at slower speed.
5. Removing too much grass - raise cutting height, cut
partial width, and cut lawn more frequently.
6. Grass is too wet from rain or dew - allow grass to dry.
7. Blades are dull or worn - inspect blades and replace as
necessary. Use only genuine SNAPPER replacement
blades.
8. Deck, blower, or hose has clipping build up - clean all
clippings from all internal surfaces.
WARNING
DO NOT put fingers or hands inside blower! STOP
blades. STOP engine. Remove key. Use only a stick, or
other suitable means, to clear the blower of clogs or
other obstructions!
k, WARNING
DO NOT attempt any adjustments, maintenance or
repairs with engine running. STOP blades. STOP
engine. Remove key.
WARNING
Grass Catcher components are subject to deteriora- I
tion. Inspect frequently. Replace worn or damaged I
components immediately. Use only genuine SNAPPER I
replacement parts. I
(Continued On Next Page)
10