Page 1
A A S S S S E E M M B B L L Y Y I I N N S S T T R R U U C C T T I I O O N N S S O O P P E E R R A A T T O O R R ' ' S S M M A A N N U U A A L L P P A A R R T T S S L L I I S S T T Actual product may differ from product pictured above...
Page 2
preliminaries C C o o n n g g r r a a t t u u l l a a t t i i o o n n s s ! ! You have just purchased one of the finest pieces of outdoor power equipment on the market today. If properly cared for, your new Z-Vac Grass Catcher Kit will provide years of dependable service.
safety rules regarding outdoor power equipment I I M M P P O O R R T T A A N N T T ! ! R R E E A A D D C C A A R R E E F F U U L L L L Y Y T T H H E E F F O O L L L L O O W W I I N N G G S S A A F F E E T T Y Y R R U U L L E E S S B B E E F F O O R R E E A A S S S S E E M M B B L L I I N N G G O O R R O O P P E E R R A A T T I I N N G G U U N N I I T T .
safety rules regarding outdoor power equipment CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the unit and its activity. Never assume that children will remain where you last saw them. -- Keep children out of the mowing area and under the watchful care...
BLOWER KIT INSTALLATION STEP 1: Remove pin, rod and spring securing dis- charge deflector to mower deck, and remove deflector. Store deflector for future use. IMPOR- TANT: Never operate any mower without a dis- charge deflector or grass catcher securely in place.
Page 6
unit assembly REMOVE BOLTS, THEN REMOVE COVER CHECK TO SEE THAT BELT IS ON PULLEYS DRILL HOLES & INSTALL BOLTS DRILL HOLE & INSTALL BOLT ALIGN SIDE OF GUARD WITH SIDE OF DECK STEP 6a: Remove bolts securing impeller pulley cover to blower, and remove cover.
STEP 9: Install belt guard between pulley guard and belt guard support clip on front part of blower mount. Secure with two 5/16 nylon wing nuts. Tighten nuts securely. WEIGHT KIT INSTALLATION !! Warning: Weight kit must be installed prior to installing bagger unit.
Page 8
unit assembly INSERT PIN INTO ROD HOOK BAGGER FRAME ONTO BUMPER MOUNT PLATE PINS CROSS ASSEMBLY INSTALL REINFORCEMENT PLATE ON BACK SIDE OF BAGGER FRAME HAIR PINS HINGES ROUND HEAD PIN SLIP CORD ONTO STUD AND SECURE WITH WASHER & NUT STEP 13: Hook bottom of bagger frame onto pins in bottom of bumper mount plate.
Page 9
STEP 18: Install bags onto cross assembly by hooking slot in bag hanger onto tabs in channel assembly. STEP 19: Close cover and lock in place by hook- ing lock knob into slot in cover latch arm. STEP 20: Slip one hose clamp onto each end of hose (use the clamp with the black quick-release knob at the blower end), and install hose between blower and bagger.
& maintenance INTRODUCTION Follow operation and maintenance instructions in the Operator’s Manual provided with the Snapper CZT/HZT. GRASS CATCHER OPERATION 1. Select desired cutting height. Choose a setting that will not attempt to cut off too much at once, overloading the machine.
Manual and Engine Owner’s Manual included with the machine. Grass Catcher bags used on SNAPPER products are made of woven fab- ric, and are subject to deterioration and wear during normal usage. Check condition of bags before each use. Immediately replace worn or damaged catcher bags with only bags recommended by SNAPPER.
Page 21
Item Part No. Qty. Description 78288 WEIGHT, 27 x 5 x 1/4” 78289 WEIGHT, 27 x 2-1/2 x 1/4” 91821 BOLT, 1/2-13 x 3” Hex Head 90254 WASHER, 1/2” Split Lock 91316 NUT, 1/2-13 Hex unit breakdown & parts list S S n n a a p p p p e e r r Z Z - - V V a a c c W W e e i i g g h h t t B B a a r r G G r r o o u u p p - - C C Z Z T T / / H H Z Z T T M M o o d d e e l l s s...
Page 23
Item Part No. Qty. Description 3046944 DECAL, Fast-Vac 1704405 DECAL, Safety, Grass Bag 3046850 DECAL, Danger, Fast-Vac 3046851 DECAL, Warning, Fast-Vac 3046883 DECAL, Warning, Fast-Vac unit breakdown & parts list S S n n a a p p p p e e r r Z Z - - V V a a c c D D e e c c a a l l G G r r o o u u p p - - C C Z Z T T / / H H Z Z T T M M o o d d e e l l s s...
For two (2) years from purchase date for the original purchaser's residential, non-commercial use, SNAPPER, through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any part or parts found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both.
Page 28
A A S S S S E E M M B B L L Y Y I I N N S S T T R R U U C C T T I I O O N N S S O O P P E E R R A A T T O O R R ' ' S S M M A A N N U U A A L L P P A A R R T T S S L L I I S S T T - - V V A A C C...