Table of Contents
Advertisement
Quick Links
OWNER'S MANUAL & OPERATING INSTRUCTIONS
2 INCH
CHEMICAL PUMP
MODEL NUMBER
66526
10006 Santa Fe Springs Road
SAVE THESE INSTRUCTIONS
Santa Fe Springs CA 90670
Important Safety Instructions
USA / 1-877-338-0999
MADE IN CHINA
are included in this manual.
REV 66526-20130930
www.championpowerequipment.com
Advertisement
Table of Contents
Related Manuals for Champion Power Equipment 66526
Summary of Contents for Champion Power Equipment 66526
- Page 1 OWNER’S MANUAL & OPERATING INSTRUCTIONS 2 INCH CHEMICAL PUMP MODEL NUMBER 66526 10006 Santa Fe Springs Road SAVE THESE INSTRUCTIONS Santa Fe Springs CA 90670 Important Safety Instructions USA / 1-877-338-0999 MADE IN CHINA are included in this manual. REV 66526-20130930 www.championpowerequipment.com...
- Page 2 AN IMPORTANT MESSAGE ABOUT TEMPERATURE: Your Champion Power Equipment product is designed and rated for continuous operation at ambient temperatures up to 40°C (104°F). When your product is needed your product may be operated at temperatures ranging from -15°C (5°F) to 50°C (122°F) for short periods.
-
Page 3: Table Of Contents
66526 2 INCH CHEMICAL PUMP TABLE OF CONTENTS Introduction ......Maintenance Schedule .... -
Page 4: Introduction
It is designed to pump liquids only. Record the model and serial numbers as well as date and place of purchase for future reference. Have this information available when ordering parts and when making technical or warranty inquiries. Champion Power Equipment Support 1-877-338-0999 Model Number... -
Page 5: Manual Conventions
Please call our help line at 1-877-338-0999 situation which, if not avoided, could result in death or serious injury. CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. REV 66526-20130930... -
Page 6: Safety Rules
All local and federal laws must be followed at all times any potentially hazardous materials IMMEDIATELY. when handling, prepping, pumping and flushing any and Chemicals, pesticides and any potentially hazardous all chemicals, pesticides, and any potentially hazardous materials can contaminate if not properly cleaned up materials. quickly. REV 66526-20130930... - Page 7 This will ensure some protection of the hose or pipe from any passing Loss of pressure and suction will occur. Property vehicles. damage and injury may also occur. REV 66526-20130930...
-
Page 8: Controls And Features
(13) Fuel Valve – Used to turn fuel supply on and off to crankcase and shuts the engine down if the level engine. falls too low. (14) Engine Switch – Used to start the engine. Oil Filler Cap – Check and fill engine oil level. REV 66526-20130930... -
Page 9: Parts Included
66526 ENGLISH CONTROLS AND FEATURES Parts Included Your Model 66526 Gasoline Powered chemical pump ships with the following parts: Other – Spark Plug Socket ..... . . -
Page 10: Assembly
3. Add up to 0.63 qt (0.6 L) of oil and replace oil fill cap/dipstick. DO NOT OVERFILL. 4. Check engine oil level daily and add as needed. WARNING Pouring fuel too fast through the fuel screen may result in blow back of fuel at the operator while filling. REV 66526-20130930... -
Page 11: Connecting Hose Or Pipes
It is advisable to always shut off the fuel supply, run the engine to fuel starvation and drain the tank when the equipment is not in use for more than 30 days. REV 66526-20130930... -
Page 12: Operation
Running the pump dry can destroy the pump seals Flushing the pump with water after using chemicals is and will void the warranty. If the pump was running while dry, stop the engine and allow it to cool recommended. thoroughly before filling the chamber with water. REV 66526-20130930... -
Page 13: Pesticides
Loss of pressure and suction will occur. Property damage and injury may also occur. NOTE If the engine will not be used for a period of two (2) weeks or longer, please see the Storage section for proper engine and fuel storage. REV 66526-20130930... -
Page 14: Operation At High Altitude
To alleviate high altitude issues other than the natural power loss, Champion Power Equipment can provide a high altitude carburetor main jet. The alternative main jet and installation instructions can be obtained by contacting Customer Support. -
Page 15: Maintenance And Storage
Once oil has been added, a visual check should show oil about 1-2 threads from running out of the fi ll hole. If using the dipstick to check oil level, DO NOT screw in the dipstick while checking. REV 66526-20130930... -
Page 16: Cleaning
Contact our help line at 1-877-338-0999 to locate the Engine Stored for Less than 30 Days nearest Champion Power Equipment certified service dealer 1. Allow the engine to cool completely before storage. 2. Clean engine according to the Maintenance section. -
Page 17: Winter Storage
It is advisable to always shut off the fuel supply, run the engine to fuel starvation and drain the tank when the equipment is not in use for more than 30 days. REV 66526-20130930... -
Page 18: Specifications
– Max Delivery Volume ..154 gal/min (583 L/min) Your Champion Power Equipment product is designed – Gross Weight ....61 lbs. (27.7 kg) and rated for continuous operation at ambient –... -
Page 19: Troubleshooting
Relocate pump so suction head is less than discharge head (maximum 98 feet) Air leak Tighten connectors and clamps or replace seal packing For further technical support: Technical Service Mon – Fri 8:30 AM – 5:00 PM (PST/PDT) Toll Free: 1-877-338-0999 tech@championpowerequipment.com REV 66526-20130930... -
Page 20: Parts Diagram
66526 ENGLISH SPECIFICATIONS Parts Diagram REV 66526-20130930... -
Page 21: Parts List
Screw ST4.8×45 222.251105.01 Valve,One Way 222.251111.01 Seal,Base Pump 222.251101.01 Body,Pump 222.251403.01 Seal,Plug 222.251401.01 Plug 1.70.1.0660 Bolt M6×60 222.251401.02 Plug 222.251403.02 Seal,Plug 6.1.114.2 Frame 1.5783.0825 Bolt M8×25 203.201400.01 Rubber Mount 1.6177.1.08 Nut M8 1.5789.0835 Flange Bolt M8×35 1.6187.1.08 Nut M8 REV 66526-20130930... -
Page 22: Engine Parts Diagram
66526 ENGLISH SPECIFICATIONS Engine Parts Diagram REV 66526-20130930... -
Page 23: Engine Parts List
26.030009.00 Gasket, Cylinder Head 24.070001.00 Fuel Valve Knob 2.04.003 Dowel Pin (Ø10×14) 1.818.0412 Bolt M4×12 23.040002.00 Valve, Intake 1.16674.0512.2 Flange Bolt M5×12 23.040006.00 Valve, Exhaust 2.06.007 Clip Ø8 26.080400.00 Air Guide, Lower 24.070011.00 Pipe, Fuel 2.15.002(F6RTC) Spark Plug(F6RTC) REV 66526-20130930... -
Page 24: Warranty
This warranty excludes: Warranty Qualifications – Cosmetic defects such as paint, decals, etc. Champion Power Equipment (CPE) will register this – Wear items such as filter elements, o-rings, etc. warranty upon receipt of your Warranty Registration Card – Accessory parts such as starting batteries, and and a copy of your sales receipt from one of CPE’s retail... - Page 25 United States Environment Protection Agency (U.S. EPA) Emission Control System Warranty Your Champion Power Equipment (CPE) engine complies with U.S. EPA emission regulations. YOUR WARRANTY RIGHTS AND OBLIGATIONS: The US EPA AND CPE are pleased to explain the Federal Emission Control Systems Warranty on your 2013 small off-road engine and engine powered equipment.
- Page 26 EMISSION CONTROL SYSTEM WARRANTY The following are specific provisions relative to your Emission Control System (ECS) Warranty Coverage. 1. APPLICABILITY: This warranty shall apply to 1997 and later model year small off-road engines. The ECS Warranty Period shall begin on the date the new engine or equipment is delivered to its original, end-use purchaser, and shall continue for 24 consecutive months thereafter.
- Page 27 You must take your CPE engine or the product on which it is installed, along with your warranty registration card or other proof of original purchase date, at your expense, to any Champion Power Equipment dealer who is authorized by Champion Power Equipment, Inc. to sell and service that CPE product during his normal business hours.
Need help?
Do you have a question about the 66526 and is the answer not in the manual?
Questions and answers