Page 1: Table Of Contents
..........Dometic Manual Awning to Solera 18V Power Awning Carefree Manual Awning to Solera 18V Power Awning .
Page 2: Introduction
NOTE: The LCI Solera Universal Hardware kit for a manual Manual awnings that contain springs use tension for ease to power conversion will ONLY fit Dometic and Carefree of operation and can be harmful to the end user should the awnings.
Page 3: Parts List
Parts List NOTE: Part numbers are shown for identification purposes only. Not all parts are available for individual sale. All parts with a link to the Lippert Store can be purchased. Solera Power 18V 69” Kit Callout 434729 Black 276611 Screw, #8-18 x 1/2”...
Page 4: Resources Required
Solera Universal Hardware ® Manual Awning to Solera 18V Power Awning (For Aftermarket Applications) Resources Required 1. On the new power awning support arm assembly, drill • 1-2 people, depending on task out the four rivets holding the original upper mounting •...
Page 5: Conversion
When converting a Dometic Manual Awning to a Solera 18V Power Awning, the converted awning will be approximately 2” wider than the initial awning. Be sure...
Page 6 Solera Universal Hardware ® Manual Awning to Solera 18V Power Awning (For Aftermarket Applications) 4. Separate the drive head from the support arm and secure the support arm to the unit in the travel position. 5. Remove the fasteners from the upper mounting bracket (Fig.6A) of the support arm assembly.
Page 7 Solera 18V Power Awning (For Aftermarket Applications) 12. Place the Solera end cap (Fig.10B) on the end of the roll tube (Fig.10A), making sure it is properly seated and the roll tube channel is aligned with the channel on the end cap.
Page 8 Solera Universal Hardware ® Manual Awning to Solera 18V Power Awning (For Aftermarket Applications) 19. To secure the drive support arm assembly: NOTE: Silicone sealant MUST be used on all screws and holes to prevent water from infiltrating the unit.
Page 9: Carefree Manual Awning To Solera 18V Power Awning
® Manual Awning to Solera 18V Power Awning (For Aftermarket Applications) Carefree Manual Awning to Solera 26. Secure the lower (Fig.15) and middle (Fig.16) sections of the drive mount arm to the unit with the provided 18V Power Awning #14 x 1 ”...
Page 10 Solera Universal Hardware ® Manual Awning to Solera 18V Power Awning (For Aftermarket Applications) NOTE: Some Carefree systems are equipped with a cam 5. Remove the fasteners from the upper mounting bracket lock assist on the drive side of the awning. If equipped, (Fig.20) of the support arm assembly.
Page 11 9. Slowly release all of the tension by rotating the drive Fig.24 head with the locking pliers. 12. Place the Solera end cap (Fig.25B) on the end of the 10. Remove the three screws securing the end cap roll tube (Fig.25A), making sure it is properly seated and (Fig.23B) to the roll tube (Fig.23A).
Page 12 #14 x 1 ” screws, aligned directly below the 15. Insert the Solera drive head assembly shaft (Fig.26B) holes of the awning removed (Fig.28). into the end cap (Fig.26A).
Page 13 Solera Universal Hardware ® Manual Awning to Solera 18V Power Awning (For Aftermarket Applications) NOTE: Silicone sealant MUST be used on all screws and holes to prevent water from infiltrating the unit. NOTE: Do NOT install fasteners to the lower and middle sections of the wall mount arm at this time.
Page 14: Charging The Battery
Solera 18V Power Awning (For Aftermarket Applications) Charging the Battery NOTE: The battery for the Solera 18V Power Pack is located inside the drive arm. The awning will operate 22 to 25 times before needing to be recharged. 1. Locate the battery wires (Fig.32A) stored inside the bottom of the drive arm.
Page 15: Adjusting The Pitch
Solera Universal Hardware ® Manual Awning to Solera 18V Power Awning (For Aftermarket Applications) Troubleshooting Adjusting the Pitch Manual Override NOTE: The awning will pitch itself to purge the pooling of In the event of power loss or motor failure, the awning can excess water and may dump a significant amount of water be extended and retracted manually.
Page 16: Maintenance
Solera Universal Hardware ® Manual Awning to Solera 18V Power Awning (For Aftermarket Applications) Maintenance NOTE: Use caution when retracting the awning manually. Fabric Care The use of a step stool or ladder may be required to completely retract the awning.
Page 17 Solera Universal Hardware ® Manual Awning to Solera 18V Power Awning (For Aftermarket Applications) Troubleshooting Chart What's Happening? What Should Be Done? If optional travel locks are installed, ensure that they have been unlocked. Verify the fuse is good. Awning won’t open or close.
Page 18: Notes
Solera Universal Hardware ® Manual Awning to Solera 18V Power Awning (For Aftermarket Applications) Notes lci1.com 574-537-8900 CCD-0001267 Rev: 03.21.19...
Page 19 Solera Universal Hardware ® Manual Awning to Solera 18V Power Awning (For Aftermarket Applications) Notes lci1.com 574-537-8900 CCD-0001267 Rev: 03.21.19...
Page 20 (For Aftermarket Applications) Notes Manual information may be distributed as a complete document only, unless Lippert Components provides explicit consent to distribute individual parts. All manual information is subject to change without notice. Revised editions will be available for free download at lci1.com.

Lippert Components Solera User Manual

Quick Links

Table of Contents

Related Manuals for Lippert Components Solera

Summary of Contents for Lippert Components Solera

Table of Contents