Lippert Components Solera Oem Installation Manual
  1. Manuals
  2. Brands
  3. Lippert Components Manuals
  4. Automobile Accessories
  5. Solera
  6. Oem installation manual
Lippert Components Solera Oem Installation Manual

Lippert Components Solera Oem Installation Manual

Slide topper
Hide thumbs Also See for Solera:
Table of Contents

Advertisement

Quick Links

Download this manual
Solera
Slide Topper
OEM INSTALLATION MANUAL
®

Advertisement

Table of Contents
loading

Related Manuals for Lippert Components Solera

Summary of Contents for Lippert Components Solera

  • Page 1 Solera Slide Topper OEM INSTALLATION MANUAL ®...

  • Page 2: Table Of Contents

    Introduction The Solera® Slide Topper with Access Plates is a high-quality, cost-effective way to help keep slide-outs free of dirt, leaves and debris. The Solera® Slide Topper is permanently attached to the slide-out and retracts/extends with the room. Additional information about this product can be obtained from lci1.com/support or by using the myLCI app.

  • Page 3: Resources Required

    NOTE: All screws supporting the awning assembly MUST have a backer within the structure of the wall of the unit. Refer to unit manufacturer for proper location. NOTE: The slide-out of the unit that the Solera Slide Topper is being installed on should not be opened more than 8".

  • Page 4: Assemble The Extension Rod And Cap

    Fig. 3 Fastener Locations Installing the Solera Slide Topper Access Plate The access plate (Fig. 4) can be mounted with the flat edge (Fig. 4A) at the top or bottom, depending on which option allows for a more square installation on the unit.
  • Page 5 Install the access plate below the T-molding (Fig. 5) or on the T-molding (Fig. 6). A. If installing below the T-molding, start on one side of the front of the slide-out by placing one of the two access brackets (Fig. 5A) against the bottom of the T-molding at the top corner of the slide-out (Fig.

  • Page 6: Installing The Solera Slide Topper Access Bracket

    The higher position (Fig. 9A), second extrusion from the top of the access bracket, is used if the slide topper requires extra clearance. NOTE: If installing the slide topper access plate on the T-molding, see "Installing Solera Slide Topper Access Plate" section (Fig.6), use the first extrusion from the top of the access bracket method (Fig. 8A).

  • Page 7: Installation Of Solera Slide Topper Assembly

    Installation of Solera Slide Topper Assembly To prepare for fabric installation, use a screwdriver to spread open either end of the awning rail on the installation end (Fig. 10A). To protect the fabric from damage during installation, file any sharp edges or burrs from the awning rail.
  • Page 8 (Fig. 8). Install two set screws in the lower two holes of the access bracket (Fig. 14A) if using the higher position (Fig. 9). Center the Solera® Slide Topper over the slide room using a tape measure. Fig. 13 Fig.

  • Page 9: Securing The Fabric

    10. Fasten the extension rods (Fig. 15A) to the access brackets (Fig. 15B) by installing two of the provided #10 - 16 x 3/4” self-drilling hex washer head screws (Fig. 15C). Fig. 15 Roll tube springs are under tension. Improperly secured roll tube springs can cause personal injury and/or product damage.
  • Page 10 The contents of this manual are proprietary and copyright protected by Lippert Components, Inc. (“LCI”).  LCI prohibits the copying or dissemination of portions of this manual unless prior written consent from an authorized LCI representative has been provided.  Any unauthorized use shall void any applicable warranty. ...

Table of Contents