Related Manuals for jcb JCB-MS-210C
Summary of Contents for jcb JCB-MS-210C
- Page 1 POWER TOOL INSTRUCTION & USER MANUAL JCB-MS-210C Original Instructions IM-MS-210C-EN...
- Page 2 JCB-MS-210C Instruction & User Manual...
- Page 3 This mitre saw is equipped with a class 2 laser. Do not look into the laser beam The month and year of manufacture can be found within the product serial number e.g. MMYYPPPAXXXXX. Where production month (MM) and production year (YY) are included. JCB-MS-210C Instruction & User Manual...
-
Page 4: Table Of Contents
Mitre cut 0°- 45° Mitre cut 0°- 45° and turntable 0°- 45° Saw blade replacement Adjusting the laser Maintenance Electrical connection AC motor Storage DISPOSAL AND RECYCLING WARRANTY STATEMENT Conditions Terms EC DECLARATION OF CONFORMITY JCB-MS-210C Instruction & User Manual... -
Page 5: General Safety Instructions
Use safety equipment. Always wear (grounded) power tools eye protection. Unmodified plugs and matching outlets Safety equipment such as dust mask, – – will reduce risk of electric shock. non-skid safety shoes, hard hat, or JCB-MS-210C Instruction & User Manual... - Page 6 A careless action can cause severe – easier to control. injury within a fraction of a second. Use the power tool, accessories and tool bits etc., in accordance with JCB-MS-210C Instruction & User Manual...
-
Page 7: Safety Instructions For Mitre Saws
Bent or warped workpieces can twist or – If your hand is placed too close to the saw shift and may cause binding on the – blade, there is an increased risk of injury spinning saw blade while cutting. There JCB-MS-210C Instruction & User Manual... - Page 8 After finishing the cut, release the supported. If the cut-off piece or switch, hold the saw head down and workpiece tips, it can lift the lower wait for the blade to stop before JCB-MS-210C Instruction & User Manual...
-
Page 9: Safty Instructions For The Handling Of Saw Blades
Prior to use, make sure that the insertion tool meets the technical requirements of this electric tool and is properly fastened. Only use the supplied saw blade for cutting wood, never for the processing of metals. JCB-MS-210C Instruction & User Manual... - Page 10 The laser may not be replaced with a different type of laser. Repairs of the laser may only be carried out by the laser manufacturer or an authorised representative JCB-MS-210C Instruction & User Manual...
- Page 11 Fasten bolt for turn table 16a. Extension block 16b. Stop rail set crew JCB-MS-210C Instruction & User Manual...
-
Page 13: Technical Data
JCB-MS-210C Instruction & User Manual... -
Page 14: Vibration And Noise Information
Try to keep emissions as low as possible, for example by limiting your working time. In this regard, all the operational cycle phases must be taken into consideration (such as the times when the tool is switched off or running idle). JCB-MS-210C Instruction & User Manual... -
Page 15: Operating Instructions
Despite use as intended, specific risk factors storage. cannot be entirely eliminated. Due to the design and layout of the machine, the following risks remain: JCB-MS-210C Instruction & User Manual... - Page 16 JCB-MS-210C Instruction & User Manual...
-
Page 17: Assembly
Assembling the support stand (fig. 1.1 – 1.2) Loosen the fix screw (14) on the • underneath of the saw through the specified holes on the back of the saw. Afterwards, retighten the fix screw (14). • JCB-MS-210C Instruction & User Manual... -
Page 18: Area Of Application
Mitre saw without guard. • Materials larger than the specified cutting • data: 120 x 60 mm 90°/90°/ 80 x 60 mm 90°/45° 120 x 33 mm 45°/90° 80 x 33 mm 45°/45° JCB-MS-210C Instruction & User Manual... -
Page 19: Settings And Working Instructions
FIXING A WORKPIECE Clamp the work piece on the work table with the workpiece clamp (10 - Fig 1) in order to fix it in place. JCB-MS-210C Instruction & User Manual... -
Page 20: Cross Cut 90° And Turntable
(3) so that the unit can also be pivoted downward. The motor starts when the ON/OFF switch • (1) is pressed. Slowly bring the saw blade down to the • workpiece and cut through it with moderate pressure. JCB-MS-210C Instruction & User Manual... -
Page 21: Cross Cut 90° And Turntable 0
• to the desired angle. The pointer on the turntable must coincide with the desired angular extent of the scale on the base (7). Re-tighten the set screw (21) to fix the • turntable (9). JCB-MS-210C Instruction & User Manual... -
Page 22: Mitre Cut 0°- 45° And Turntable 0
(in this connection see also section “Mitre cut 0°- 45°”). Re-tighten the locking konb (17). • Cut as described under section “Cross cut • 90° and turntable 0°”. JCB-MS-210C Instruction & User Manual... -
Page 23: Saw Blade Replacement
• Place a new saw blade on the inner saw rotational direction of the saw blade. • tighten the screw. • Move the saw blade guard back to the cor- rect position. JCB-MS-210C Instruction & User Manual... -
Page 24: Adjusting The Laser
We recommend using a suction tool or brush. ATTENTION: Do not use compressed air! Check the saw blade from time to time: If problems arise with the blade, it must be ground by a specialist or replaced, depending on the condition. JCB-MS-210C Instruction & User Manual... -
Page 25: Electrical Connection
Places where the connection cables have • and humidity. been cut due to being driven over. Keep the operating manual with the power Insulation damage due to being ripped out • tool. of the wall outlet. JCB-MS-210C Instruction & User Manual... -
Page 26: Disposal And Recycling
You can obtain information on collection points for waste equipment from your municipal administration, public waste disposal authority, an authorised body for the disposal of waste electrical and electronic equipment or your waste disposal company. JCB-MS-210C Instruction & User Manual... -
Page 27: Conditions
Warranty cover commences from the date of purchase on the retail sales receipt and is valid only for JCB Tools products purchased within the UK bearing the CE mark and a visible serial number. In the unlikely event your JCB Power Tool is subject to a manufacturing fault within the warranty period, JCB Tools may repair the product by replacing defective parts free of charge at our discretion. -
Page 28: Warranty Statement
JCB Power Tools used for Hire Fleets or as part of B2B and Service Contracts are not covered by these terms and conditions. JCB Tools standard 2 Year warranty excludes the following (where relevant); • Components normally subject to wear such as carbon brushes. -
Page 29: Terms
The person authorized to compile the technical file: Date: 04/01/2019 Signature: Name/ title: Mya Yee Lwin / Quality Assurance Manager Address: JCB Tools, 55 Romsey Industrial Estate,Romsey, SO51 0HR,UK. (REG: 11062222) Company Registration Number: 1062222 JCB-MS-210C Instruction & User Manual...
Need help?
Do you have a question about the JCB-MS-210C and is the answer not in the manual?
Questions and answers