Page 3
Trademarks Copyright @2002 PLANEX COMMUNICATIONS INC. Contents subject shall be change without prior notice. Pci is a registered trademark of PLANEX COMMUNICATIONS INC. All other trademarks belong to their respective proprietors. FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
BRL-04FXP BRL-04FXP Chapter 1 Introduction Chapter 5 Print Server Functions and Features........Configuring on Windows 95/98 Platforms ... Packing List ............. Configuring on Windows NT Platforms ..Chapter 2 Hardware Introduction Configuring on Windows 2000 Platforms..Panel Layout ........... Configuring on Unix based Platforms...
Chapter 1 Introduction BRL-04FXP C ongratulations on your purchase of this outst anding B roadband Rout er. Thi s product is s pecificall y desi gned for Small Office and Hom e Off i c e needs. It provides a complete SOHO solution for Internet surfing and office resources shari ng, and it is easy to configure and operate for even non- technical users.
Chapter 2 Hardware Installation BRL-04FXP ● Packet Filter supported Panel Layout Packet Filter enables you to control what packets are allowed to pass the router. ■ Front Panel ● Virtual Server supported Enable you to expose WWW, FTP and other services on your LAN to be accessible to Internet users.
BRL-04FXP BRL-04FXP ■ Rear Panel In addition, remember to turn off the power, remove the power cord from the outlet, and keep your hands dry when you try to install the hardware of this product. Procedure for Hardware Installation 1 . Set up L AN c o n n e c t i o n : co nn ect an Et her net cabl e fro m y ou r...
Chapter 3 Network Settings and Software Installation BRL-04FXP 4. Power on: To use this product correctl y, you have to properly confi gure t he network Connecting the power cord to power inlet and turning the power switch settings of your computers and install the attached setup program into your on, this product will automatically enter the self-test phase.
BRL-04FXP BRL-04FXP There must be something wrong in your installation procedure. You have to Step 2: Click on the "for Win9x" or "for WinNT/2000/XP" button. Wait check the following items in sequence: until the following Welcome dialog to appear, and click on the Next button.
Chapter 4 CONFIGURING NAT Router BRL-04FXP Step 4: When the following window is displayed, click on the Finish button. This product provides Web based configuration scheme that is, configuring b y Netscape C ommuni cator or Internet Expl orer. Thi s ap proach can be adopted in any MS Windows, Macintosh or UNIX based platforms.
Page 11
BRL-04FXP BRL-04FXP ■ Dynamic IP Address 3. PPPoE Account : The Account provided by the ISP for the PPPoE DSL 1. Select ”Dynamic IP Address” button connection 4. PPPoE Password : The password provided by the ISP for the PPPoE DSL 2.
BRL-04FXP BRL-04FXP 7. PPTP Passwo rd: Th e p as sword p ro vid ed by th e ISP for the PPTP Setup connection. 8. Click "Save" button. 9. Click the "Reboot" in the left-hand column then finish of setting.
Page 13
BRL-04FXP BRL-04FXP LAN I P Address : th is produ ct's IP addres s. T he defaul t add res s i s 3.Domain Name: Optional, this informat ion wil l be passed to the cl ient. 192.168.1.1. You can change it on your need.
Page 14
BRL-04FXP BRL-04FXP 1. Select ”Synamic IP Address“ button 4.PPPoE Password : The password provided by the ISP for the PPPoE DSL 2. Click ”Setup...” button connection 5.Service Name : The Service Name provi ded by the ISP for the PPPoE DSL connection(SeedNet's user must be key in ”speed11”)
Page 15
BRL-04FXP BRL-04FXP 4. My Subnet Mask : The mask that ISP assigned to your PC. Toolbox 5. Server IP Address : The IP address of the DSL modem. 6. PPTP Acco unt : T he Accou nt prov id ed by th e ISP fo r th e PPTP connection.
Page 16
BRL-04FXP BRL-04FXP ■ Reset to Default This product's NAT firewall filters out unrecognized packets to protect your 1.Click ”Reset to Default” button. Intranet, so all hosts behind this product are invisible to the outside world. If you wish, you can make some of them accessible by enabli ng t he Vi r t u a l Server Mapping.
Page 17
BRL-04FXP BRL-04FXP ■ ■ Special Applications Packet Filter Some applications require multiple connections, like Internet games, Video ■ Outbound Packet Filter conferencin g, and In ternet t eleph ony and so on . Due to the fi rewal l Packet Filter enables you to control what packets are allowed to pass the functi on, these appl icati ons can not work with pure NAT rout er.
Page 18
BRL-04FXP BRL-04FXP ■ For source or destination port, you can define a single port (80) or a range of MAC Control ports (1000-1999). Add prefix "T" or "U" to specify TCP or UDP protocol. For example, T80, U53, U2000-2999. No prefi x indicates both TCP and UDP are defined.
Page 19
BRL-04FXP BRL-04FXP ■ ■ Dynamic DNS Support Routing Dynamic DNS support enables users to enjoy domain name even they have no fi xed IP address. The proposed system supports the foll owi ng DDNS providers: Routing Table ● WWW.DYNDNS.ORG Th e device can allo w us ers t o defi ne t he i nternal routi ng table to best ●...
Page 20
BRL-04FXP BRL-04FXP ■ Static Routing can perform remote admini strati on. If the speci fied IP address i s 0.0.0.0, Static rout ing enables user t o confi gure routi ng t able by themselves. The any host can connect to this product to perform administration task. When this feature is enabled, the web port will be shifted to 88.
Chapter 5 Print Server BRL-04FXP This product provides the function of network print server for MS Windows 95/98/NT and Unix based platforms. (If the product you purchased doesn't have printer port, please skip this chapter.) Configuring on Windows 95/98 Platforms...
BRL-04FXP BRL-04FXP 1. Find out the corresponding icon of your server printer, for example, the Configuring on Windows NT Patforms HP LaserJet 6L. Click the mouse's right button on that icon, and then The configuration procedure for a Windows NT platform is similar to that...
Appendix A Restore to Factory Setting BRL-04FXP 1. Please push reset button on back panel. Configuring on Unix based Patforms 2. Push the Reset button for three second ,and please stop push reset when Please follow the traditional configuration procedure on Unix platforms to M1 start blinking.
TCP/IP Configuration for Wi n d o w s 9 5 / 9 8 / BRL-04FXP T his s ect ion i ntrodu ces yo u how to i nst al l TC P/ IP prot ocol i nto yo ur personal computer.
Page 25
BRL-04FXP BRL-04FXP b. Don 't input any value in the Gateway tab. 3. Click Properties button to set the TCP/IP protocol for this NAT Router. 4. Now, you have two setting methods: c. Choose Disable DNS in the DNS Configuration tab.