Advertisement
Available languages
Available languages
Batteries and Power
This D
WALT rotary laser will accept all D
e
is built to best resist damage during a fall when used with the following batteries:
All 1.5Ah and 2Ah D
WALT 20 volt lithium ion batteries.
e
Charging the Battery Pack
The battery pack is not fully charged out of the carton. You need to use a
D
WALT 20 volt charger to charge the battery pack before you can use the
e
rotary laser.
• Refer to the chart at the end of this manual for compatibility of chargers and
battery packs.
• Be sure to read all safety instructions before using your charger.
WARNING:
DO NOT attempt to charge the battery pack with any chargers
other than the ones listed in this manual. The charger and battery
pack are specifically designed to work together.
WARNING:
Carefully follow all instructions and warnings on the battery label and
package and accompanying Battery Safety Manual.
1.
Slide the battery pack into the charger as described in the Battery Safety
Manual.
2.
Wait until the battery pack is fully charged.
3.
Slide the battery pack out of the charger.
NOTE: When ordering replacement battery packs, be sure to include the catalog
number and voltage.
Installing the 20V D
WALT Battery Pack
e
1.
Position the fully-charged 20V DeWALT battery pack so the release button
(Figure
) is facing away from you and to the right.
D 1
2.
Press and hold down the release button (Figure
3.
Slide the battery pack all the way into the track on the side of the laser
(Figure
).
D 2
4.
Release the button on the battery pack.
Removing the Battery Pack
1.
Press and hold the release button on the battery pack (Figure
2.
Slide the battery pack out of the track on the laser.
3.
Release the button on the battery pack.
4.
To recharge the battery pack, insert it into the charger, as described in the
Battery Safety Manual.
WALT 20 volt lithium ion batteries, but
e
) on the battery pack.
D 1
).
D 1
WARNING:
Batteries can explode or leak, and can cause injury or fire. To reduce
this risk, follow the instructions in the Battery Safety Manual.
Storing Battery Packs
• The best storage place is one that is cool and dry, and away from direct
sunlight and excess heat or cold.
• Long storage will not harm the battery pack or charger. Under proper
conditions, they can be stored for 5 years or more.
SAVE THESE INSTRUCTIONS FOR FUTURE USE
Installing the Coin Cell Battery
A coin cell battery should already be installed in the bottom of the laser unit
(Figure
) so it is ready to use the Bluetooth
D 3
cell battery in the future, follow these steps.
1.
Carefully turn the laser upside down.
2.
On the bottom of the laser, unscrew the battery compartment cover, which is
marked 3V CR2430.
3.
Lift off the battery compartment cover and remove the old coin cell battery.
4.
Insert a new 3V CR2430 coin cell battery into the battery compartment.
5.
Carefully place the battery compartment cover back in the correct position and
use the screws to secure the cover in place on the bottom of the laser unit.
THE BLUETOOTH
WORD MARK AND LOGOS ARE REGISTERED TRADEMARKS OWNED
®
BY BLUETOOTH SIG, INC. AND ANY USE OF SUCH MARKS BY DEWALT IS UNDER LI-
CENSE. APPLE AND THE APPLE LOGO ARE TRADEMARKS OF APPLE INC., REGISTERED
IN THE U.S. AND OTHER COUNTRIES. APP STORE IS A SERVICE MARK OF APPLE INC.,
REGISTERED IN THE U.S. AND OTHER COUNTRIES. GOOGLE PLAY AND THE GOOGLE
PLAY LOGO ARE TRADEMARKS OF GOOGLE INC.
Installing Batteries in the Remote
Load new AAA batteries into the remote so you can use it with the laser unit.
1.
On the bottom of the remote, lift up the latch to open the battery compartment
cover (Figure
).
C 1
2.
Insert two new, high-quality, name brand AAA batteries, making sure to position
the - and + ends of each battery as noted inside the battery compartment
(Figure
).
C 2
3.
Push the battery compartment cover closed until it snaps into place
(Figure
).
C 3
connection. To replace the coin
®
13
E
Advertisement
