Panasonic DP-100 Series Instruction Manual page 2

7 RUN MODE
Setting the threshold value
Refer to <Comparative output 1 / 2 output mode setting>, <Analogue voltage
 FXUUHQW RXWSXW  H[WHUQDO LQSXW VHOHFWLRQ! in "
setting conditions.
The Sub display conducts the threshold value. Main display does not changed.
EASY mode
(Comparative output 2 is OFF)
Comparative output 1
EASY mode
Comparative output 2
Comparative output 1
Hysteresis mode / Window
comparator mode · Lo side
Comparative output 2
Comparative output 1
Hysteresis mode / Window
comparator mode · Hi side
Comparative output 2
Notes: 1) If the set pressure range is exceeded, "
appear on the sub display. " " will also appear if the Hi side threshold value exceeds the Lo side threshold
value when setting the "hysteresis mode / window comparator mode" threshold value.
2) Auto-reference value and remote zero-adjustment value are displayed.
For details, refer to " 11 AUTO-REFERENCE FUNCTION" and "
TION."
3) In the dash line box is not displayed when not setting "
method, refer to $QDORJXH YROWDJH  FXUUHQW RXWSXW  H[WHUQDO LQSXW VHOHFWLRQ! in "
MODE."
Zero-adjustment function
The zero-adjustment function forcibly sets the pressure value to "zero" when the
pressure port is opened.
Key lock function
The key lock function prevents key operations so that the conditions set in each
setting mode are not inadvertently changed.
<Key lock set>
<Key lock released>
Peak / bottom hold function
The peak / bottom hold functions display the peak value and bottom value of the
ÀXFWXDWLQJ SUHVVXUH
The peak value is displayed on the main display and the bottom value is displayed
on the sub-display.
The higher vacuum side indicates the peak value, while the lower vacuum side in-
dicates the bottom value.
<Peak / bottom hold set>
Hold down
<Peak / bottom hold released>
Hold down
8 MENU SETTING MODE" for
Display is changed by pressing down.
Automatic
Press: Increase threshold value to high pressure side.
Press: Decrease threshold value to low pressure side.
Blinks alternately
" (exceeds the upper limit) or " " (exceeds the lower limit) will
12 REMOTE ZERO-ADJUSTMENT FUNC-
" or " " in external input switch. For the setting
Hold down Automatic
Hold down Automatic
Hold down Automatic
Blinks alternately
8 MENU SETTING MODE
The mode will change to RUN mode when the mode selection key is held down
during this setting process. In doing so, changed items before holding down the
mode selection key have been set.
RUN mode
Press for 2 sec.
<Comparative output 1 output mode setting>
EASY mode
Standard type
<Comparative output 2 output mode setting> (Note 1)
OFF mode
(Note 2) (Note 3)
High-function type
<Analogue voltage / current output / external input selection>
Analogue
voltage output
8 MENU SETTING
Standard type
<N.O. / N.C. selection> (Note 1)
Output 1: N.O.
Output 2: N.O.
High-function type
<N.O. / N.C. selection>
N.O.
<Response time setting>
2.5ms
<Display color of the main display selection>
Red when ON
Green when OFF
<Unit selection> (Note 2)
MPa
RUN mode
Notes: 1) If the comparative output 2 output mode setting is set to "
as the high-function type.
2) The default setting of the low pressure type is "
3) This is not displayed on the high pressure type.
Setting item
Comparative output 1
output mode setting
Comparative output 2
output mode setting
(Standard type only)
Analogue voltage /
current output / ex-
ternal input selection
(High-function type only)
N.O. / N.C. selection
Response time setting
Displayed color of the
main display selection
Unit selection
Window
Hysteresis comparator
mode mode
Window
Hysteresis comparator
EASY mode mode mode
Remote
Auto-refer- zero-adjust- Analogue
ence input ment input current output
Output 1: N.C. Output 1: N.O. Output 1: N.C.
Output 2: N.C. Output 2: N.C. Output 2: N.O.
N.C.
5ms 5,000ms
Green when ON
Red when OFF Always red Always green
2
kPa kgf/cm bar
inchHg (Note 3)
", " " is not displayed.
Factory setting
Sets the output operation of comparative output 1.
Sets the output operation of comparative output 2.
Selects analogue voltage / current output, auto-reference input, or remote
zero-adjustment input.
Low pressure type
Normal open (N.O.) or normal close (N.C.) can be selected.
High pressure type
Sets the response time.
The response time can be selected from 2.5ms, 5ms, 10ms, 25ms, 50ms,
100ms, 250ms, 500ms, 1,000ms or 5,000ms.
Displayed color of the main indicator can be changed.
Low pressure type
Pressure unit can be changed.
High pressure type
psi
mmHg (Note 3)
", the display of N.O. / N.C. selection is the same
Description